Trouble with Mac hard drive
I am running Slax 6.0.7 (boot from CDROM) which is based off of Slackware 12.1. I am having trouble mounting the hard drive on the macbook.
It looks like the scsi drive is not found correctly. I can only see the boot sector of the drive (/dev/sda1). I think there should be anther partition (/dev/sda2) that holds the data. I looked at fdisk (which i think doesn't support hfsplus drives) so i ran parted on it and saw two paritions. From the dmesg i get the following on the scsi: Loading iSCSI transport class v2.0-724. iscsi: registered transport (tcp) Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver 1.1-5[2449]-ms aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded scsi: <fdomain> Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver iscsi: registered transport (qla4xxx) QLogic iSCSI HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.2.2 Copyright(c) 2004-2007 Emulex. All rights reserved. seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers and the following about the sda scsi2 : ata_piix scsi3 : ata_piix ata1: SATA max UDMA/133 cmd 0x20d8 ctl 0x20fc bmdma 0x2020 irq 19 ata2: SATA max UDMA/133 cmd 0x20d0 ctl 0x20f8 bmdma 0x2028 irq 19 ata1.01: ATA-7: ST96812AS, 7.01, max UDMA/133 ata1.01: 117210240 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.01: configured for UDMA/133 scsi 2:0:1:0: Direct-Access ATA ST96812AS 7.01 PQ: 0 ANSI: 5 sd 2:0:1:0: [sda] 117210240 512-byte hardware sectors (60012 MB) sd 2:0:1:0: [sda] Write Protect is off sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:1:0: [sda] 117210240 512-byte hardware sectors (60012 MB) sd 2:0:1:0: [sda] Write Protect is off sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 2:0:1:0: [sda] Attached SCSI disk Does anyone have any ideas what i am doing wrong here? Any help would be great. Thanks |
Please post your thread in only one forum. Posting a single thread in the most relevant forum will make it easier for members to help you and will keep the discussion in one place. This thread is being closed because it is a duplicate.
Please continue this here. |
All times are GMT -5. The time now is 03:24 PM. |