LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices


Reply
  Search this Thread
Old 12-02-2005, 07:26 PM   #16
camus
LQ Newbie
 
Registered: Nov 2005
Posts: 6

Rep: Reputation: 0

"First, post your fstab if it is the same as the one above then that is your problem."

/dev/hda2 / reiserfs acl,user_xattr 1 1
/dev/hda1 swap swap defaults 0 0
proc /proc proc defaults 0 0
sysfs /sys sysfs noauto 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
/dev/cdrom /media/cdrom subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 0 0
/dev/fd0 /media/floppy subfs noauto,fs=floppyfss,procuid,nodev,nosuid,sync 0 0

dmesg:
Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (p
rerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fed0000 (usable)
BIOS-e820: 000000000fed0000 - 000000000fef0000 (ACPI NVS)
BIOS-e820: 000000000fef0000 - 000000000ff00000 (reserved)
BIOS-e820: 00000000feea0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
254MB LOWMEM available.
found SMP MP-table at 000f7c40
On node 0 totalpages: 65232
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61136 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 COMPAQ ) @ 0x000e0010
ACPI: RSDT (v001 COMPAQ CPQ0014 0x20001127 0x00000000) @ 0x000e0080
ACPI: FADT (v001 COMPAQ SOLANO 0x00000001 0x00000000) @ 0x000e0130
ACPI: SSDT (v001 COMPAQ CORE_UTL 0x00000001 MSFT 0x0100000d) @ 0x000e0d81
ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x0100000d) @ 0x000e0ef5
ACPI: SSDT (v001 COMPAQ FHUB 0x00000001 MSFT 0x0100000d) @ 0x000e2d98
ACPI: MADT (v001 COMPAQ SOLANO 0x00000001 0x00000000) @ 0x000e01a4
ACPI: SSDT (v001 COMPAQ APIC 0x00000001 MSFT 0x0100000d) @ 0x000e2d22
ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x0100000d) @ 0x000e1db5
ACPI: SSDT (v001 COMPAQ S1 0x00000001 MSFT 0x0100000d) @ 0x000e2462
ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf808
ACPI: local apic disabled
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: COMPAQ Product ID: Deskpro APIC at: 0xFEE00000
Processor #0 6:8 APIC version 16
I/O APIC #8 Version 17 at 0xFEC00000.
Processors: 1
Allocating PCI resources starting at 0ff00000 (gap: 0ff00000:eefa0000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 selinux=0 x11i=vesa resume=/dev/hda1 spl
ash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 631.397 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253136k/260928k available (2028k kernel code, 7272k reserved, 700k data,
204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1264.00 BogoMIPS (lpj=2528014)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 0
0000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Celeron (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1657k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0a20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xe8316, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *9
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x400-0x41f has been reserved
pnp: 00:0d: ioport range 0x420-0x43f has been reserved
pnp: 00:0d: ioport range 0x440-0x45f has been reserved
pnp: 00:0d: ioport range 0x460-0x47f could not be reserved
pnp: 00:0d: ioport range 0xf800-0xf81f could not be reserved
pnp: 00:0d: ioport range 0xf820-0xf83f could not be reserved
pnp: 00:0d: ioport range 0xf840-0xf85f has been reserved
pnp: 00:0d: ioport range 0xf860-0xf87f has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: 40000000-402fffff
PREFETCH window: 0ff00000-0fffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1133575515.052:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 HUB COM1 COM2 USB1 USB2 PBTN
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
ICH: IDE controller at PCI slot 0000:00:1f.1
ICH: chipset revision 2
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2460-0x2467, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x2468-0x246f, BIOS settings: hdcMA, hddio
Probing IDE interface ide0...
hda: WDC WD200EB-11CPF0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19541088 sectors (10005 MB) w/2048KiB Cache, CHS=19386/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2
Probing IDE interface ide1...
hdc: LTN485, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU0] (supports 8 throttling states)
hdc: ATAPI 48X CD-ROM drive, 120kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 514040k swap on /dev/hda1. Priority:-1 extents:1
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA
]
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0x44000000
hw_random hardware driver 1.0.0 loaded
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
i810_smbus 0000:00:02.0: i810/i815 i2c device found.
ip6_tables: (C) 2000-2002 Netfilter core team
i8xx TCO timer: failed to reset NO_REBOOT flag, reboot disabled by hardware
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ip_tables: (C) 2000-2002 Netfilter core team
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:00:1f.2 (0004 -> 0005)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ
11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 11, io base 0x00002440
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ip_conntrack version 2.1 (2038 buckets, 16304 max) - 248 bytes per conntrack
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ
5
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0a.0: 3Com PCI 3c905B Cyclone 100baseTx at 0x1000. Vers LK1.1.19
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ
11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 70032 usecs
intel8x0: clocking to 41161
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ
5
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PBTN]
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 17
NET: Registered protocol family 24
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 already at revision 0x8 (current=0x8)
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
powernow: This module only works with AMD K7 CPUs
eth0: no IPv6 routers present
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=213.94.240.5 DST=193.77.140.125 LEN=
90 TOS=0x00 PREC=0x00 TTL=54 ID=62698 PROTO=UDP SPT=14735 DPT=13499 LEN=70
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=213.25.101.236 DST=193.77.140.125 LE
N=90 TOS=0x00 PREC=0x00 TTL=119 ID=50710 PROTO=UDP SPT=24602 DPT=13499 LEN=70
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=193.77.140.252 DST=193.77.140.125 LE
N=48 TOS=0x00 PREC=0x00 TTL=127 ID=43023 DF PROTO=TCP SPT=1742 DPT=445 WINDOW=16
384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=193.77.140.252 DST=193.77.140.125 LE
N=48 TOS=0x00 PREC=0x00 TTL=127 ID=43229 DF PROTO=TCP SPT=1742 DPT=445 WINDOW=16
384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=140.116.117.45 DST=193.77.140.125 LE
N=90 TOS=0x00 PREC=0x00 TTL=106 ID=63405 PROTO=UDP SPT=9785 DPT=13499 LEN=70
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=193.77.140.252 DST=193.77.140.125 LE
N=48 TOS=0x00 PREC=0x00 TTL=127 ID=45510 DF PROTO=TCP SPT=2108 DPT=445 WINDOW=16
384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=193.77.140.252 DST=193.77.140.125 LE
N=48 TOS=0x00 PREC=0x00 TTL=127 ID=45712 DF PROTO=TCP SPT=2108 DPT=445 WINDOW=16
384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
ide-cd: cmd 0x28 timed out
hdc: DMA interrupt recovery
hdc: lost interrupt
hdc: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdc: DMA disabled
hdc: drive not ready for command
hdc: ATAPI reset complete

I had to delete second half of dmesg result becaus I got the message that my reply is too long. I hope this helps.
To became more confusing I can see cd drive after some reboots - not if cd is in the drive, but if I put it in after the system is loaded.
 
Old 12-05-2005, 12:40 AM   #17
lxuzer
LQ Newbie
 
Registered: Jun 2005
Distribution: SuSE Linux 10.1
Posts: 26

Original Poster
Rep: Reputation: 15
could it be a hardware issue? impossibe as 9.3 worked flawlwess. Obviously, I havent tried everything posible that I could find on google, otherwise, I would have resolved it. I must play now the waiting game patiently.
 
Old 12-07-2005, 08:10 PM   #18
lxuzer
LQ Newbie
 
Registered: Jun 2005
Distribution: SuSE Linux 10.1
Posts: 26

Original Poster
Rep: Reputation: 15
Well... the struggle continues....

The mount point for
hdg = /media/cdrecorder
hdh = /media/dvdrecorder


If i go to those folders, nothing happens, but as soon as I mount the devices, when the folder is clicked, I get "No Media in device for /media/cdrecorder" or "No Media in device for /media/dvdrecorder." If I umount, I dont get the error message. Again, the only way the system acknowledges cd/dvd is by going to yast>hardware>cd-rom.

I hope someone out there has the same problem with a fix.

Help... thanks!
 
Old 12-07-2005, 09:45 PM   #19
slantoflight
Member
 
Registered: Aug 2005
Distribution: Smoothwall
Posts: 283
Blog Entries: 3

Rep: Reputation: 35
I have same problem in Suse 10. I have two cdrom drives, I'm not sure if thats an issue. I solved it so far by loging in as root and manual mounting /dev/dvd /media/dvd. Now the problem is can't unmount it.


I'll post my fstab when I get back on my linux box.

Last edited by slantoflight; 12-07-2005 at 09:46 PM.
 
Old 12-08-2005, 05:26 AM   #20
lxuzer
LQ Newbie
 
Registered: Jun 2005
Distribution: SuSE Linux 10.1
Posts: 26

Original Poster
Rep: Reputation: 15
"Try this

Create a file with kate or what ever, with this line

/usr/sbin/hwinfo --cdrom > /dev/null 2>&1

save to '/etc/init.d' as 'after.local' ( remove ' )

this will run at boot up and initialise your CDROM Drives

Ram"

http://www.linuxformat.co.uk/modules...ewtopic&t=1713

Last edited by lxuzer; 12-08-2005 at 03:05 PM.
 
Old 12-08-2005, 07:58 AM   #21
rimcrazy
Member
 
Registered: Dec 2003
Location: Overgaard, AZ
Distribution: Suse 10.0, FC5, RHEL4
Posts: 32

Rep: Reputation: 15
Double Entry

Having the exact same problem. Again, if I go into YaST after reboot, select the DVD and then ADD, the CDROM and ADD and quit YaST then everything works. Something very wrong is going on in the hardware detection. Just installed the new kernel patch that was posted. Problem is still there.

Sound is hosed too but I'll save that for another thread. I'd like to figure out what in blazes is causing this problem.

Any ideas where we could look?
 
Old 12-08-2005, 09:48 AM   #22
rimcrazy
Member
 
Registered: Dec 2003
Location: Overgaard, AZ
Distribution: Suse 10.0, FC5, RHEL4
Posts: 32

Rep: Reputation: 15
A little more info.

I installed suse 10 on top of suse 9.3 with an upgrade not a clean install.
It appears that all of the links in the /dev directory pointing to both
the dvdrecorder and the cdrom are removed at boot. When you go into
YaST and add them again, the links are there. Reboot the machine and
now the links are gone. Given that when you open up Yast and it thinks
you have two of each device possibly that is triggering something in the boot
process that is removing the links in the /dev directory. Once
you do the add, everything works fine. Reboot and they are gone again.

This is a semi-major pain the the ass. You go to the Suse Forum
and there is nada....in fact that forum appears to have turned to crap
the way they have split it up.
 
Old 12-08-2005, 03:01 PM   #23
lxuzer
LQ Newbie
 
Registered: Jun 2005
Distribution: SuSE Linux 10.1
Posts: 26

Original Poster
Rep: Reputation: 15
My previous post has the solution!
 
Old 12-08-2005, 03:27 PM   #24
slantoflight
Member
 
Registered: Aug 2005
Distribution: Smoothwall
Posts: 283
Blog Entries: 3

Rep: Reputation: 35
Heres what works for me. I just change the fstab, change the zero to ones

/dev/dvd /media/dvd subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 1 1

Works beautifully well, I can even eject cds now.
 
Old 12-09-2005, 05:01 AM   #25
knp01
LQ Newbie
 
Registered: Dec 2005
Posts: 4

Rep: Reputation: 0
i had similar problems getting iso9660 cds mounted.
changed the fstype from subfs to iso9660 and presto it worked.
also cd's now burnt would read on other boxen.
perhaps you could try this?
 
Old 12-09-2005, 06:40 AM   #26
rimcrazy
Member
 
Registered: Dec 2003
Location: Overgaard, AZ
Distribution: Suse 10.0, FC5, RHEL4
Posts: 32

Rep: Reputation: 15
So far none of these address the issue. In the /dev directory you should see the following:

105][root@opus /dev]# ls -al cdrom
lrwxrwxrwx 1 root root 3 2005-12-09 05:38 cdrom -> hdh
106][root@opus /dev]# ls -al dvd
lrwxrwxrwx 1 root root 3 2005-12-09 05:37 dvd -> hdg
107][root@opus /dev]# ls -al dvdrecorder
lrwxrwxrwx 1 root root 3 2005-12-09 05:37 dvdrecorder -> hdg
108][root@opus /dev]# ls -al cdrecorder
lrwxrwxrwx 1 root root 3 2005-12-09 05:37 cdrecorder -> hdg

These links exist after I go to yast and reinstall the DVD,CDROM. On
boot these are all gone. Kicking the automounter or changing the mount
type don't work in this case. The root cause has to something with
how hardware is being recognized but I'm just not sure where.

My fstab looks like the following:
/dev/hde4 / reiserfs acl,user_xattr 1 1
/dev/hda1 /archive vfat users,gid=users,umask=0002,utf8=true 0 0
/dev/hdf1 /backup vfat users,gid=users,umask=0002,utf8=true 0 0
/dev/hde5 /data vfat users,gid=users,umask=0002,utf8=true 0 0
/dev/hde1 /winxp ntfs ro,users,gid=users,umask=0002,nls=utf8 0 0
/dev/hde3 swap swap pri=42 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
proc /proc proc defaults 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
sysfs /sys sysfs noauto 0 0
/dev/dvdrecorder /media/dvdrecorder subfs noauto,fs=cdfss,rw,procuid,nosuid,nodev,exec 0 0
/dev/cdrom /media/cdrom subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec 0 0
/dev/fd0 /media/floppy subfs noauto,fs=floppyfss,procuid,nodev,nosuid,sync 0 0
none /subdomain subdomainfs noauto 0 0

Checking dmesg after boot there is a curious set of errors when the SCSI system initializes:

hdg: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdh: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
SCSI subsystem initialized
st: Version 20050501, fixed bufsize 32768, s/g segs 256
hdg: command error: status=0x51 { DriveReady SeekComplete Error }
hdg: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdg, sector 64
Buffer I/O error on device hdg, logical block 16
hdg: command error: status=0x51 { DriveReady SeekComplete Error }
hdg: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdg, sector 68
Buffer I/O error on device hdg, logical block 17
hdg: command error: status=0x51 { DriveReady SeekComplete Error }
hdg: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdg, sector 64
Buffer I/O error on device hdg, logical block 16
hdg: command error: status=0x51 { DriveReady SeekComplete Error }
hdg: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdg, sector 68
Buffer I/O error on device hdg, logical block 17
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
mount as a device: mount dvd-iso file in /dev/dvd sadarax Linux - General 21 02-02-2011 11:59 PM
mount:not a directory. Suse dvd mount problem tzanis Linux - General 8 11-06-2005 11:30 AM
Suse 9.1 Yast2 breaks DVD mount slaw219 Linux - Software 1 07-23-2004 10:50 AM
suse dvd mount problem tzanis Linux - General 1 03-13-2004 06:28 PM
suse dvd mount problem tzanis Linux - General 1 03-13-2004 01:16 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware

All times are GMT -5. The time now is 09:30 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration