LinuxQuestions.org
Review your favorite Linux distribution.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices


Reply
  Search this Thread
Old 11-30-2003, 09:38 PM   #1
jamil5454
Member
 
Registered: Nov 2003
Location: houston
Distribution: slackware 9.1
Posts: 41

Rep: Reputation: 15
radeon 9600 install on suse 9.0


I just finished installing the new Suse 9.0 via FTP and it recognized my graphics card when installing - "RV350 AP". I decided I wanted 3d acceleration for all the games that come with suse9 and so i went to the ATI site and downloaded their linux RPM for xfree86 4.3. Well I followed ATI's installation notes(rpm -Uhv [rpmfile] then run fglrxconfig). I then restarted my computer and Xserver launched successfully and the ATI Control Panel correctly identifies all aspects of my card. Problem is that I'm still seeing the generic MESA OGL driver as the default instead of the newly installed ATI one. I'm tryin to make the full switch to linux but this is the only thing deterring me . I looked in the XF86Config-4 File and everything seems to be fine, but I probably wouldn't spot a problem if I saw one. As you can probably see I'm a pretty big newb. Thanks for the help - greatly appreciated.

XF86Config-4 (no XF86Config):

# File: XF86Config-4
# File generated by fglrxconfig (C) ATI Research, a substitute for xf86config.

# Note by ATI: the below copyright notice is there for servicing possibly
# pending third party rights on the file format and the instance of this file.
#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# DRI Section
# **********************************************************************
Section "dri"
# Access to OpenGL ICD is allowed for all users:
Mode 0666
# Access to OpenGL ICD is restricted to a specific user group:
# Group 100 # users
# Mode 0660
EndSection

# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx" # libglx.a
Load "dri" # libdri.a

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
# FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
# FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5 - 68.7
VertRefresh 60 - 85
Option "DPMS"

# === mode lines based on GTF ===
# VGA @ 100Hz
# Modeline "640x480@100" 43.163 640 680 744 848 480 481 484 509 +hsync +vsync
# SVGA @ 100Hz
# Modeline "800x600@100" 68.179 800 848 936 1072 600 601 604 636 +hsync +vsync
# XVGA @ 100Hz
# Modeline "1024x768@100" 113.309 1024 1096 1208 1392 768 769 772 814 +hsync +vsync
# 1152x864 @ 60Hz
# Modeline "1152x864@60" 81.642 1152 1216 1336 1520 864 865 868 895 +hsync +vsync
# 1152x864 @ 85Hz
# Modeline "1152x864@85" 119.651 1152 1224 1352 1552 864 865 868 907 +hsync +vsync
# 1152x864 @ 100Hz
# Modeline "1152x864@100" 143.472 1152 1232 1360 1568 864 865 868 915 +hsync +vsync
# 1280x960 @ 75Hz
# Modeline "1280x960@75" 129.859 1280 1368 1504 1728 960 961 964 1002 +hsync +vsync
# 1280x960 @ 100Hz
# Modeline "1280x960@100" 178.992 1280 1376 1520 1760 960 961 964 1017 +hsync +vsync
# SXGA @ 100Hz
# Modeline "1280x1024@100" 190.960 1280 1376 1520 1760 1024 1025 1028 1085 +hsync +vsync
# SPEA GDM-1950 (60Hz,64kHz,110MHz,-,-): 1280x1024 @ V-freq: 60.00 Hz, H-freq: 63.73 KHz
# Modeline "GDM-1950" 109.62 1280 1336 1472 1720 1024 1024 1026 1062 -hsync -vsync
# 1600x1000 @ 60Hz
# Modeline "1600x1000" 133.142 1600 1704 1872 2144 1000 1001 1004 1035 +hsync +vsync
# 1600x1000 @ 75Hz
# Modeline "1600x1000" 169.128 1600 1704 1880 2160 1000 1001 1004 1044 +hsync +vsync
# 1600x1000 @ 85Hz
# Modeline "1600x1000" 194.202 1600 1712 1888 2176 1000 1001 1004 1050 +hsync +vsync
# 1600x1000 @ 100Hz
# Modeline "1600x1000" 232.133 1600 1720 1896 2192 1000 1001 1004 1059 +hsync +vsync
# 1600x1024 @ 60Hz
# Modeline "1600x1024" 136.385 1600 1704 1872 2144 1024 1027 1030 1060 +hsync +vsync
# 1600x1024 @ 75Hz
# Modeline "1600x1024" 174.416 1600 1712 1888 2176 1024 1025 1028 1069 +hsync +vsync
# 1600x1024 @ 76Hz
# Modeline "1600x1024" 170.450 1600 1632 1792 2096 1024 1027 1030 1070 +hsync +vsync
# 1600x1024 @ 85Hz
# Modeline "1600x1024" 198.832 1600 1712 1888 2176 1024 1027 1030 1075 +hsync +vsync
# 1920x1080 @ 60Hz
# Modeline "1920x1080" 172.798 1920 2040 2248 2576 1080 1081 1084 1118 -hsync -vsync
# 1920x1080 @ 75Hz
# Modeline "1920x1080" 211.436 1920 2056 2264 2608 1080 1081 1084 1126 +hsync +vsync
# 1920x1200 @ 60Hz
# Modeline "1920x1200" 193.156 1920 2048 2256 2592 1200 1201 1203 1242 +hsync +vsync
# 1920x1200 @ 75Hz
# Modeline "1920x1200" 246.590 1920 2064 2272 2624 1200 1201 1203 1253 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 1400x1050 @ 60Hz M9 Laptop mode
# ModeLine "1400x1050" 122.000 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync
# 1920x2400 @ 25Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@25" 124.620 1920 1928 1980 2048 2400 2401 2403 2434 +hsync +vsync
# 1920x2400 @ 30Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@30" 149.250 1920 1928 1982 2044 2400 2402 2404 2434 +hsync +vsync

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# installed.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# === ATI device section ===

Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
# === disable PnP Monitor ===
#Option "NoDDC"
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"
# === FireGL DDX driver module specific settings ===
# === Screen Management ===
Option "DesktopSetup" "0x00000000"
Option "MonitorLayout" "AUTO, AUTO"
Option "IgnoreEDID" "off"
Option "HSync2" "unspecified"
Option "VRefresh2" "unspecified"
Option "ScreenOverlap" "0"
# === TV-out Management ===
Option "NoTV" "yes"
Option "TVStandard" "NTSC-M"
Option "TVHSizeAdj" "0"
Option "TVVSizeAdj" "0"
Option "TVHPosAdj" "0"
Option "TVVPosAdj" "0"
Option "TVHStartAdj" "0"
Option "TVColorAdj" "0"
Option "GammaCorrectionI" "0x00000000"
Option "GammaCorrectionII" "0x00000000"
# === OpenGL specific profiles/settings ===
Option "Capabilities" "0x00000000"
# === Video Overlay for the Xv extension ===
Option "VideoOverlay" "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
# will be disabled automatically
Option "OpenGLOverlay" "off"
# === Center Mode (Laptops only) ===
Option "CenterMode" "off"
# === Pseudo Color Visuals (8-bit visuals) ===
Option "PseudoColorVisuals" "off"
# === QBS Management ===
Option "Stereo" "off"
Option "StereoSyncEnable" "1"
# === FSAA Management ===
Option "FSAAScale" "1"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
# === Misc Options ===
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "yes"
Option "ForceGenericCPU" "no"
BusID "PCI:1:0:0" # vendor=1002, device=4150
Screen 0
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "640x480" "800x600" "1024x768" "1152x864" "1280x960" "1280x1024"
ViewPort 0 0 # initial origin if mode is smaller than desktop
# Virtual 1280 1024
EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Server Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.

Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

### EOF ###
 
Old 12-01-2003, 12:46 AM   #2
Guru3
Member
 
Registered: Sep 2003
Location: //home/sweden
Distribution: RedHat 9, Fedora Core 1
Posts: 360

Rep: Reputation: 31
Where are you "still seeing the generic MESA OGL driver"? There are alot of places that show up. Have you tried running fgl_glxgears?
 
Old 12-01-2003, 06:09 AM   #3
jamil5454
Member
 
Registered: Nov 2003
Location: houston
Distribution: slackware 9.1
Posts: 41

Original Poster
Rep: Reputation: 15
I see it when I run fglrxinfo or when I launch the ATI control panel. Also, when I try to play any games it says I don't have hardware acceleration and the games run really slow. When I run fgl_glxgears I get the message "Error: couldn't get fbconfig". Any ideas? I think the problem with the XF86Config-4 file. It's still loading the MESA libraries instead of the ATI ones. Anyone else out there have an ATI card and got their 3d acceleration working? Can I see your XF86Config-4 File?

Last edited by jamil5454; 12-01-2003 at 06:13 AM.
 
Old 12-01-2003, 10:05 AM   #4
Guru3
Member
 
Registered: Sep 2003
Location: //home/sweden
Distribution: RedHat 9, Fedora Core 1
Posts: 360

Rep: Reputation: 31
re-install the rpm with the force option-- in RH9 there is a mesa library that the RPM overwrites. maybe in suse it skipped it? ie rpm -ivh --force fglrx.rpm
 
Old 12-01-2003, 10:20 AM   #5
Robattack
LQ Newbie
 
Registered: Dec 2003
Location: Frankfurt, Germany
Distribution: mandriva2006 /dsl-2.0/gentoo-2006.0
Posts: 25

Rep: Reputation: 15
ati 9500pro and SuSE9.0

hi @ all

I've nearly the same problem as you. I'm sorry, but I have no solution for you. But a question.
Do you get some error message while the installation ????
I get some. I dont have the exact text now, but its about my kernel version. It says, that a kernel-version of 2.4.8 or higher is needed, and hardware acceleretion will not work with the SuSE kernel 2.4.21 - 99 .

after the "installation" i run fglrxconfig, which works fine and no error messages appear. But on the ati control panel i see the mesa driver as the default driver too.

Maybe you got any idea?

Thanks!
 
Old 12-01-2003, 11:35 AM   #6
sirra462
Member
 
Registered: Nov 2003
Posts: 58

Rep: Reputation: 15
This error is the missing fglrx kernel module. It means that you need this module installed in the kernel for the fglrx driver to be fully utilized. From SuSE's website you can get what you need.
here

click on fglrx driver update and that will bring you to an FTP server or just ftp to:

ftp://ftp.suse.com/pub/suse/i386/sup...90/fglrx/3.2.8

view the readme and follow the directions. Then install the ATI drivers and you should get no kernel module errors. I think, but I am not sure, that the fglrx.rpm is SuSE's version of the ATI driver. You may be better off just using it, or if you prefer to use ATI's driver install that instead of this one.
I am currently in the process of getting this to work, I had not installed the km_fglrx into the kernel before doing this and I think that once this is accomplished (quite easy following the directions) the drivers should work fine.
 
Old 12-01-2003, 04:57 PM   #7
bkp_42
LQ Newbie
 
Registered: Nov 2003
Posts: 4

Rep: Reputation: 0
Same problem here.

I downloaded the drivers from the above link, and followed the directions. No errors during install. Upon reboot however, I get errors from 3D apps claiming that 3D has not been configured. Checked the XFree 86 log and found this:

(WW) fglrx(0): Cannot read colourmap from VGA. Will restore with default
(II) fglrx(0): UMM area: 0xf0500000 (size=0x07b00000)
(II) fglrx(0): driver needs XFree86 version: 4.3.x
(II) fglrx(0): detected XFree86 version: 4.3.0
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
(II) fglrx(0): FBADPhys: 0xf0000000 FBMappedSize: 0x08000000
(WW) fglrx(0): Failed to set up write-combining range (0xf0000000,0x8000000)
(II) fglrx(0): FBMM initialized for area (0,0)-(1024,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1024,768) (front color buffer - assumption)
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) fglrx(0): Using hardware cursor (scanline 768)
(II) fglrx(0): Largest offscreen area available: 1024 x 7419
(**) Option "dpms"
(**) fglrx(0): DPMS enabled
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): Direct rendering disabled
(II) Loading extension FGLRXEXTENSION
(II) Loading extension ATITVOUT


Any idea why DRI Initialization would be failing?
 
Old 12-01-2003, 07:53 PM   #8
bkp_42
LQ Newbie
 
Registered: Nov 2003
Posts: 4

Rep: Reputation: 0
Needless to say I'm a newbie... Not sure if this is an omission in the README that came with the ATI fglrx drivers, or if it's an ID Ten T (idiot ) error on my part. I currently have the above drivers loaded and working. glxgears gives me around 2300 fps at 1280x1024.

The one thing I did differently was issue the following command after rebooting and logging in as root:

modprobe fglrx

Restart the X Server after that, and off to the races. One side note though - I tried 1400x1050 first, and the X Server failed to load. Lowered it to 1280x1024 and it came up fine. My mistake was that I assumed that the command "make -f Makefile.module install" would have loaded the kernel module, but I was wrong.

Good luck everyone, and I hope this helps somebody
 
Old 12-04-2003, 05:08 AM   #9
Robattack
LQ Newbie
 
Registered: Dec 2003
Location: Frankfurt, Germany
Distribution: mandriva2006 /dsl-2.0/gentoo-2006.0
Posts: 25

Rep: Reputation: 15
Talking

@ Sirra462

Now my 3D hardware acceleration is working.

Thanks a lot for your Help!!!!!
 
Old 03-11-2004, 02:56 PM   #10
Stealthy_C
LQ Newbie
 
Registered: Sep 2003
Posts: 29

Rep: Reputation: 15
Quote:
Originally posted by sirra462
This error is the missing fglrx kernel module. It means that you need this module installed in the kernel for the fglrx driver to be fully utilized. From SuSE's website you can get what you need.
here

click on fglrx driver update and that will bring you to an FTP server or just ftp to:

ftp://ftp.suse.com/pub/suse/i386/sup...90/fglrx/3.2.8

view the readme and follow the directions. Then install the ATI drivers and you should get no kernel module errors. I think, but I am not sure, that the fglrx.rpm is SuSE's version of the ATI driver. You may be better off just using it, or if you prefer to use ATI's driver install that instead of this one.
I am currently in the process of getting this to work, I had not installed the km_fglrx into the kernel before doing this and I think that once this is accomplished (quite easy following the directions) the drivers should work fine.

THANX!

I think ive tryed that same README file before and COULD NOT get it to work. Ended up reisntalling SuSe.

But after getting the drivers fron SuSe for ATI, every thing works better now and I have 3D !!
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
ATI Radeon 9600 Pro - SuSe 0.2 Zoot-88 Linux - Newbie 3 05-01-2006 03:41 AM
Suse 9.3 install ati radeon 9600 drivers thebeast SUSE / openSUSE 1 05-28-2005 04:14 PM
Install Radeon 9600 Pro Drivers - SuSe 9.2 Zoot-88 Linux - Newbie 1 04-20-2005 06:03 PM
Radeon 9600 Pro with Suse 9.0 asteroidblitz Linux - Hardware 6 12-29-2003 06:31 AM
SuSE 9 ATI Radeon 9600 Pro hindenbergbaby Linux - Distributions 2 11-16-2003 08:10 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware

All times are GMT -5. The time now is 08:00 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration