Radeon 7000 PCI problem

jallabert · 01-11-2004, 04:55 PM

I bought a radeon 7000 PCI because i want to have two monitors, but i can't get the card to work. I use gentoo with the 2.6.1 kernel and i have the radeon module (the one called "ATI Radeon" when i compiled the kernel). I have this in my XF86Config

Quote:

Section "Device"
Identifier "Radeon"
Driver "radeon"
EndSection

This is what dmesg say about the card

Quote:

[drm] Initialized radeon 1.9.0 20020828 on minor 0

and lspci

Quote:

02:0b.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]

When i try to start x i get this

Quote:

(WW) RADEON: No matching Device section for instance (BusID PCI:2:11:0) found
(EE) No devices detected.

This is when i test if only that card is working, so i dont think it can be becasue i have two graphics cards. What is wrong and how can i fix it?

bdp · 01-12-2004, 02:01 AM

i use a radeon 7000 PCI for a second monitor. here's the XF86Config file if useful:

http://128.111.83.139/bp/XF86Config

jallabert · 01-12-2004, 09:46 AM

Quote:

Originally posted by bdp
i use a radeon 7000 PCI for a second monitor. here's the XF86Config file if useful:

http://128.111.83.139/bp/XF86Config

I got the same error after i changed it to like you have. :/

bdp · 01-12-2004, 11:19 PM

it might be beneficial to post your XF86Config, also have you tried setting the PCI card to primary in your BIOS?

jallabert · 01-13-2004, 11:32 AM

Quote:

Originally posted by bdp
it might be beneficial to post your XF86Config, also have you tried setting the PCI card to primary in your BIOS?

I haven't tried to set the card to primary.. here is my XF86Config

Quote:

Section "Module"

# This loads the DBE extension module.
Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx"
Load "dri"
Load "GLcore"
EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"
EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "se"

EndSection

# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "Buttons" "4"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection

# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

Identifier "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 94

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 75

EndSection

Section "Monitor"
Identifier "Monitor 2"
HorizSync 30-70
VertRefresh 50-160
EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.

BusID "PCI:01:00.0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# Device configured by xf86config:

Section "Device"
Identifier "NVIDIA GeForce"
Driver "nvidia"
BusID "PCI:01:00.0"
EndSection

Section "Device"
Identifier "Radeon"
Driver "radeon"
VendorName "ATI Technologies Inc"
BoardName "Radeon RV100 QY [Radeon 7000/VE]"
Option "ForcePCIMode" "True"
BusID "PCI:02:0b.0"
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.

Section "Screen"
Identifier "Screen 1"
Device "NVIDIA GeForce"
Monitor "My Monitor"
DefaultDepth 24

Subsection "Display"
Depth 8
Modes "1600x1200" "1280x1024" "1152x864" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1600x1200" "1280x1024" "1152x864" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1600x1200" "1280x1024" "1152x864" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection

Section "Screen"
Identifier "Screen 2"
Device "Radeon"
Monitor "Monitor 2"
DefaultDepth 24

Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen "Screen 1"
Screen "Screen 2" LeftOf "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

But when i try only the radeon card i change it..

edit: hm, it must be something wrong with the bus id.. when i have that on the geforce card i cant start x.