LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (https://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   QLA2200 Fabric HBA not in Fabric mode (https://www.linuxquestions.org/questions/linux-hardware-18/qla2200-fabric-hba-not-in-fabric-mode-144938/)

phillip rill 02-11-2004 03:11 PM

QLA2200 Fabric HBA not in Fabric mode
 
PowerEdge 1650, Red Hat Linux 7.2, kernel 2.4.9-33

QLA2200 installed using Fast!UTIL with "Connection Option" set to 1 as instructions indicate. The following messages file indicates the port is in loop mode and a "switchshow" command on the Brocade 2800 switch indicates L-port (not F for Fabric as wanted)
NOTE: All HP-UX servers connected show "F" fabric mode .

/var/log/messages
eb 11 11:55:14 denrmoug02 kernel: scsi0: Found a QLA2200 @ bus 3, device 0x8,
irq 4, iobase 0xbc00
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Configure NVRAM parameters...
Feb 11 11:55:14 denrmoug02 kernel: qla2x00: 64 Bit PCI Addressing Enabled
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Verifying loaded RISC code...
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Verifying chip...
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): LIP reset occurred
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Waiting for LIP to complete...
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): LIP occurred.
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): LOOP UP detected
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Waiting for LIP to complete...
Feb 11 11:55:14 denrmoug02 kernel: scsi0: Topology - (FL_Port), Host Loop addres
s 0x7d
Feb 11 11:55:14 denrmoug02 kernel: scsi-qla00-adapter-port=210000e08b056d78\;
Feb 11 11:55:14 denrmoug02 kernel: scsi-qla00-tgt-000-di-00-node=20000060b069bd2
b\;
Feb 11 11:55:14 denrmoug02 kernel: scsi-qla00-tgt-000-di-00-port=20000060b069bd2
b\;
Feb 11 11:55:14 denrmoug02 kernel: scsi-qla00-tgt-000-di-00-control=00\;
Feb 11 11:55:14 denrmoug02 kernel: scsi-qla00-tgt-000-di-00-preferred=ffffffffff
ffffffffffffffffffffffffffffffffffffffffffffffffffffff\;
Feb 11 11:55:14 denrmoug02 kernel: scsi(0): Waiting for LIP to complete...
Feb 11 11:55:14 denrmoug02 kernel: scsi0: Topology - (FL_Port), Host Loop addres
s 0x7d
Feb 11 11:55:14 denrmoug02 kernel: scsi0 : QLogic QLA2200 PCI to Fibre Channel H
ost Adapter: bus 3 device 8 irq 4
Feb 11 11:55:14 denrmoug02 kernel: Firmware version: 2.01.35, Driver ve
rsion 5.31.RH1


switchshow
port 6: sw Online F-Port 50:06:0b:00:00:0a:34:c8
port 7: sw Online E-Port 10:00:00:60:69:10:51:3f "SW2"
port 8: sw Online L-Port 1 public

What else needs to be done?


All times are GMT -5. The time now is 08:23 PM.