LinuxQuestions.org - one of three sata drives not being detected

here is the dmesg file for the comp. Some info removed for length...

Linux version 2.6.20-1.2925.fc6 (brewbuilder@hs20-bc1-7.build.redhat.com) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 SMP Sat Mar 10 19:15:16 EST 2007
BIOS-provided physical RAM map:
127MB HIGHMEM available.
896MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262128
early_node_map[1] active PFN ranges
0: 0 -> 262128
On node 0 totalpages: 262128
DMA zone: 40 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4056 pages, LIFO batch:0
Normal zone: 2200 pages used for memmap
Normal zone: 223080 pages, LIFO batch:31
HighMem zone: 319 pages used for memmap
HighMem zone: 32433 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 AOpen ) @ 0x000f7810
ACPI: RSDT (v001 AOpen AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: FADT (v001 AOpen AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff30c0
ACPI: MADT (v001 AOpen AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff7e40
ACPI: DSDT (v001 AOPEN AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 2171.666 MHz processor.
Built 1 zonelists. Total pages: 259569
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07aa000 soft=c078a000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029968k/1048512k available (2187k kernel code, 17724k reserved, 1157k data, 236k init, 131008k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc074a000 - 0xc0785000 ( 236 kB)
.data : 0xc0622ca1 - 0xc0744494 (1157 kB)
.text : 0xc0400000 - 0xc0622ca1 (2187 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4345.00 BogoMIPS (lpj=2172502)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) XP 2700+ stepping 01
Total of 1 processors activated (4345.00 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=40 bytes
sizeof(inode)=420 bytes
sizeof(dentry)=144 bytes
sizeof(ext3inode)=596 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1408 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb840, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5100-0x513f has been reserved
PCI: Bridge: 0000:00:08.0
IO window: d000-dfff
MEM window: ea000000-ebffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: e8000000-e9ffffff
PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2266k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1174341526.777:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key CB44B0DE33F9027F
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (59 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD800JB-00FMA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: WDC WD2500JB-00GVC0, ATA DISK drive
hdd: LITE-ON DVDRW LH-20A1H, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdc: max request size: 512KiB
hdc: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(33)
hdc: cache flushes supported
hdc: hdc1
ide-floppy driver 0.99.newide
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 681 not supported
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 236k freed
Write protecting the kernel read-only data: 841k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 16, io mem 0xec080000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 17, io mem 0xec082000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 18, io mem 0xec085000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
sata_promise 0000:01:0b.0: version 1.05
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 19
ata1: SATA max UDMA/133 cmd 0xF8832200 ctl 0xF8832238 bmdma 0x0 irq 19
ata2: SATA max UDMA/133 cmd 0xF8832280 ctl 0xF88322B8 bmdma 0x0 irq 19
scsi0 : sata_promise
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-6, max UDMA/133, 234441648 sectors: LBA48
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/133
scsi1 : sata_promise
usb 2-1: new low speed USB device using ohci_hcd and address 2
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-6, max UDMA/133, 156301488 sectors: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD1200JD-00H 08.0 PQ: 0 ANSI: 5
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
scsi 1:0:0:0: Direct-Access ATA ST380817AS 3.42 PQ: 0 ANSI: 5
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 2-1: configuration #1 chosen from 1 choice
input: HID 1267:0103 as /class/input/input1
input: USB HID v1.10 Keyboard [HID 1267:0103] on usb-0000:00:02.1-1
input: HID 1267:0103 as /class/input/input2
input: USB HID v1.10 Device [HID 1267:0103] on usb-0000:00:02.1-1
usb 2-2: new low speed USB device using ohci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input3
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.1-2
usb 2-3: new full speed USB device using ohci_hcd and address 4
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 2-3: configuration #1 chosen from 1 choice
usb 1-3: new full speed USB device using ohci_hcd and address 3
usb 1-3: configuration #1 chosen from 1 choice
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
usb 1-3.4: new low speed USB device using ohci_hcd and address 4
usb 1-3.4: configuration #1 chosen from 1 choice
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1174341535.326:2): selinux=0 auid=4294967295
gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x201, speed 693kHz
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 22 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[ec083000-ec0837ff] Max Packet=[2048] IR/IT contexts=[4/4]
input: X10 Wireless Technology Inc USB Receiver as /class/input/input4
usbcore: registered new interface driver ati_remote
drivers/usb/input/ati_remote.c: Registered USB driver ATI/X10 RF USB Remote Control v. 2.2.1
drivers/usb/input/ati_remote.c: Weird data, len=1 ff 00 00 00 00 00 ...
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 21 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:04.0 to 64
nvidia: module license 'NVIDIA' taints kernel.
Linux video capture interface: v2.00
input: PC Speaker as /class/input/input5
eth0: forcedeth.c: subsystem: 0a0a0:02f7 bound to 0000:00:04.0
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 20
NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:06.0 to 64
cx2388x v4l2 driver version 0.0.6 loaded
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
BUG: warning at drivers/ieee1394/ohci1394.c:233/get_phy_reg() (Tainted: P )
[<f89c661d>] get_phy_reg+0x88/0x105 [ohci1394]
[<f89c7d4b>] ohci_devctl+0x49/0x5ae [ohci1394]
[<c04049b0>] apic_timer_interrupt+0x28/0x30
[<c04ec31f>] delay_tsc+0xb/0x13
[<f89ca07c>] ohci_irq_handler+0x378/0x785 [ohci1394]
[<c044f09d>] handle_IRQ_event+0x1a/0x3f
[<c0450082>] handle_fasteoi_irq+0x72/0xa7
[<c0450010>] handle_fasteoi_irq+0x0/0xa7
[<c04062be>] do_IRQ+0xb5/0xdb
[<c04048f3>] common_interrupt+0x23/0x28
[<c042b8db>] __do_softirq+0x54/0xba
[<c04061b1>] do_softirq+0x59/0xb1
[<c0419df6>] smp_apic_timer_interrupt+0x76/0x80
[<c04049b0>] apic_timer_interrupt+0x28/0x30
[<c061fc3a>] _spin_unlock_irqrestore+0xa/0xc
[<f89c7d5f>] ohci_devctl+0x5d/0x5ae [ohci1394]
[<f8a0fab5>] csr1212_generate_csr_image+0x310/0x365 [ieee1394]
[<f8a0701c>] hpsb_reset_bus+0x1c/0x22 [ieee1394]
[<c043481a>] run_workqueue+0x85/0x125
[<c061fc1f>] _spin_lock_irqsave+0x9/0xd
[<f8a08e4e>] delayed_reset_bus+0x0/0xcd [ieee1394]
[<c043518c>] worker_thread+0xf9/0x124
[<c04226ab>] default_wake_function+0x0/0xc
[<c0435093>] worker_thread+0x0/0x124
[<c043779f>] kthread+0xb0/0xd9
[<c04376ef>] kthread+0x0/0xd9
[<c0404b33>] kernel_thread_helper+0x7/0x10
=======================
BUG: warning at drivers/ieee1394/ohci1394.c:262/set_phy_reg() (Tainted: P )
[<f89c6536>] set_phy_reg+0x97/0xf6 [ohci1394]
[<f89c7d5f>] ohci_devctl+0x5d/0x5ae [ohci1394]
[<c04049b0>] apic_timer_interrupt+0x28/0x30
[<c04ec31f>] delay_tsc+0xb/0x13
[<f89ca07c>] ohci_irq_handler+0x378/0x785 [ohci1394]
[<c044f09d>] handle_IRQ_event+0x1a/0x3f
[<c0450082>] handle_fasteoi_irq+0x72/0xa7
[<c0450010>] handle_fasteoi_irq+0x0/0xa7
[<c04062be>] do_IRQ+0xb5/0xdb
[<c04048f3>] common_interrupt+0x23/0x28
[<c042b8db>] __do_softirq+0x54/0xba
[<c04061b1>] do_softirq+0x59/0xb1
[<c0419df6>] smp_apic_timer_interrupt+0x76/0x80
[<c04049b0>] apic_timer_interrupt+0x28/0x30
[<c061fc3a>] _spin_unlock_irqrestore+0xa/0xc
[<f89c7d5f>] ohci_devctl+0x5d/0x5ae [ohci1394]
[<f8a0fab5>] csr1212_generate_csr_image+0x310/0x365 [ieee1394]
[<f8a0701c>] hpsb_reset_bus+0x1c/0x22 [ieee1394]
[<c043481a>] run_workqueue+0x85/0x125
[<c061fc1f>] _spin_lock_irqsave+0x9/0xd
[<f8a08e4e>] delayed_reset_bus+0x0/0xcd [ieee1394]
[<c043518c>] worker_thread+0xf9/0x124
[<c04226ab>] default_wake_function+0x0/0xc
[<c0435093>] worker_thread+0x0/0x124
[<c043779f>] kthread+0xb0/0xd9
[<c04376ef>] kthread+0x0/0xd9
[<c0404b33>] kernel_thread_helper+0x7/0x10
=======================
ohci1394: fw-host0: SelfID received outside of bus reset sequence
intel8x0_measure_ac97_clock: measured 50727 usecs
intel8x0: clocking to 47433
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 21
cx88[0]: Your board isn't known (yet) to the driver. You can
cx88[0]: try to pick one of the existing card configs via
cx88[0]: card=<n> insmod option. Updating to the latest
cx88[0]: version might help as well.
CORE cx88[0]: subsystem: 1002:00f9, board: UNKNOWN/GENERIC [card=0,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00018013944ffb19]
cx88[0]/0: found at 0000:01:09.0, rev: 5, irq: 21, latency: 32, mmio: 0xea000000
tuner 2-0060: All bytes are equal. It is not a TEA5767
tuner 2-0060: chip found @ 0xc0 (cx88[0])
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
tuner 2-0060: tuner type not set
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
lp0: using parport0 (interrupt-driven).
lp0: console ready
sonypi: Sony Programmable I/O Controller Driver v1.26.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
input: Power Button (FF) as /class/input/input6
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
No dock devices found.
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.8)
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k