hey hey

i have a usr 56k modem that i am trying to config in slackware 9.0. In red hat i just used linuxconf and installed it that way. but i have no idea how to do it in slackware. any help would be awesome.

thx in advance
Phukd in hed

type lspci -v as root

than post it & I will help u more.

well its not pci. its external. but here it is

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133] (rev 81)
Subsystem: Asustek Computer, Inc.: Unknown device 802c
Flags: bus master, medium devsel, latency 0
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f4000000-f5efffff
Prefetchable memory behind bridge: f5f00000-f7ffffff
Capabilities: [80] Power Management version 2

00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: Asustek Computer, Inc.: Unknown device 802c
Flags: bus master, stepping, medium devsel, latency 0

00:04.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Flags: bus master, stepping, medium devsel, latency 32
I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2

00:04.2 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2

00:04.3 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2

00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Flags: medium devsel
Capabilities: [68] Power Management version 2

00:0e.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
Subsystem: Ensoniq Creative SoundBlaster AudioPCI 128
Flags: bus master, slow devsel, latency 32, IRQ 10
I/O ports at b800 [size=64]
Capabilities: [dc] Power Management version 1

01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
Memory at f6000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at f5ff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 2.0

What u do nott say that. U can use kppp to set it up. Just make shure the com port u are useing is on in bios.