LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (https://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   Mounting SCSI R/W Drive (https://www.linuxquestions.org/questions/linux-hardware-18/mounting-scsi-r-w-drive-477091/)

KornFused 08-24-2006 06:25 PM
Mounting SCSI R/W Drive
 
I know this problem is faced by many people because there are numerous post about it, but I haven't found the one that will answer my situation.

I have a Pioneer DVD drive (ISA) and then my R/W drive is a Plextor SCSI Drive. I can play CDs from both drives. When I try to burn a CD with K3B it only sees the Pioneer Drive.

Here is the fstab output:

cat /etc/fstab
# Pluggable devices are handled by uDev, they are not in fstab
/dev/hda1 / ext3 defaults,noatime 1 1
/dev/hda2 swap swap sw,pri=1 0 0
none /proc proc defaults 0 0
none /proc/bus/usb usbfs devmode=0666 0 0
none /dev/pts devpts mode=0622 0 0
none /sys sysfs defaults 0 0
/dev/hda3 /home ext3 defaults,noatime 1 2
/dev/cdrom /media/cdrom iso9660,udf noauto,users,exec,ro 0 0
/dev/fd0 /media/floppy vfat,ext2 noauto,users,exec,rw 0 0
# Dynamic entries below, identified by 'users' option
/dev/sda1 /mnt/sda1 ext3 noauto,users,exec 0 0
/dev/sda2 /mnt/sda2 vfat,ext3,ext2,reiserfs noauto,users,exec 0 0
/dev/fd0 /media/floppy vfat,ext2 noauto,users,exec,rw 0 0

Here are the entries from DMESG

[ 92.781866] Type: CD-ROM ANSI SCSI revision:
02
[ 92.781908] target0:0:2: Beginning Domain Validation
[ 92.783967] target0:0:2: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 92.785287] target0:0:2: Domain Validation skipping write tests
[ 92.785299] target0:0:2: Ending Domain Validation
[ 92.791235] sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 92.791806] sr 0:0:2:0: Attached scsi CD-ROM sr0

I tried this with the following results:

root@1[~]# mount dev/sr0 /media/cdrw
mount: special device dev/sr0 does not exist

Brian1 08-24-2006 07:09 PM
Not sure exactly where to start here but a Scsi CD device will be IDed as /dev/scd*.
If the only scsi cd type device and no USB or Firewire CD devices then it should be /dev/scd0
Lets make sure that exist before going on.

Brian1

KornFused 08-25-2006 06:47 PM
This is gettin more and more confusing
 
Brian,

It looks like you have taken me under your wing.

I went to /dev/ and found SCD0 listed there. I checked the permissions there and made sure they were set to RW for everyone.

Then I tried this:
root@3[~]# mount /dev/scd0 /media/cdrw
mount: No medium found

I then added this line to fstab

# Pluggable devices are handled by uDev, they are not in fstab
/dev/hda1 / ext3 defaults,noatime 1 1
/dev/hda2 swap swap sw,pri=1 0 0
none /proc proc defaults 0 0
none /proc/bus/usb usbfs devmode=0666 0 0
none /dev/pts devpts mode=0622 0 0
none /sys sysfs defaults 0 0
/dev/hda3 /home ext3 defaults,noatime 1 2
/dev/cdrom /media/cdrom iso9660,udf noauto,users,exec,ro 0 0
/dev/fd0 /media/floppy vfat,ext2 noauto,users,exec,rw 0 0
# Dynamic entries below, identified by 'users' option
/dev/sda1 /mnt/sda1 ext3 noauto,users,exec 0 0
/dev/sda2 /mnt/sda2 vfat,ext3,ext2,reiserfs noauto,users,exec 0 0
/dev/scd0 /media/cdrw iso9660,udf noauto,users,exec,rw 0 0
/dev/fd0 /media/floppy vfat,ext2 noauto,users,exec,rw 0 0

Then I tried to attach the drive into K3b

It said there was no such device in the /dev folder.

I rebooted my computer and the line I added to FSTAB disappeared.
It seems that the FSTAB file is updated on boot up.

Brian1 08-26-2006 10:26 AM
There are a few things that update fstab file. One the service called kudzu. Second using the mount point in /media is not the best way. change the mount point to
/dev/scd0 /mnt/cdrw auto noauto,users,exec,rw 0 0
Make sure you have a directory /mnt/cdrw created.

K3B should not require a line in fstab to recognize a drive for writing purposes. Not sure what is going on here. Lets check a few things.
Version of K3B using?
How was K3B installed? source or package like rpm or deb
Firmware of the drive?
Scsi card model and version?
Loaded modules? /sbin/lsmod

If the scsi module is loaded and drive is seen in /dev as /dev/scd0 then I have the feeling it may be a firmware of the drive or K3B itself. Since using 2.6 kernel then the ide-scsi emualtion is not needed in the boot loader.

Brian1

KornFused 08-26-2006 11:23 AM
Here are my dumps
 
Brian,

Here is my system information

Password:
root@1[~]# deldir /media/cdrw
-su: deldir: command not found
root@1[~]# rmdir /media/cdrw
root@1[~]# mkdir /mnt/cdrw
root@1[~]# mount /dev/scd0 /mnt/cdrw
mount: No medium found
root@1[~]# /sbin/lsmod
Module Size Used by
r128 38912 1
drm 66196 2 r128
binfmt_misc 11144 1
apm 19692 1
ppdev 8452 0
ipt_limit 2432 2
ipt_state 2048 66
ipt_LOG 6016 2
ipt_REJECT 5248 2
ip_conntrack_ftp 7280 0
ip_conntrack_irc 6640 0
ip_conntrack 47148 3 ipt_state,ip_conntrack_ftp,ip_conntrack_irc
nfnetlink 6296 1 ip_conntrack
ndiswrapper 156628 0
cpufreq_userspace 4440 0
cpufreq_powersave 1920 0
cpufreq_ondemand 6172 0
speedstep_lib 4228 0
freq_table 4484 0
processor 23360 0
dm_mod 52152 0
md_mod 64084 0
yenta_socket 25740 0
rsrc_nonstatic 12288 1 yenta_socket
pcmcia 36668 0
pcmcia_core 38672 3 yenta_socket,rsrc_nonstatic,pcmcia
af_packet 21000 2
usbhid 33888 0
sworks_agp 8864 0
amd_k7_agp 8204 0
ali_agp 6656 0
sis_agp 8452 0
ati_agp 8332 0
nvidia_agp 7964 0
via_agp 9600 0
8139cp 20352 0
floppy 55620 0
parport_pc 32708 1
lp 10820 0
parport 32968 3 ppdev,parport_pc,lp
pcspkr 2052 0
8139too 25088 0
mii 5376 2 8139cp,8139too
rtc 12468 0
psmouse 32772 0
serio_raw 6916 0
snd_als4000 13280 2
snd_sb_common 14848 1 snd_als4000
gameport 14728 1 snd_als4000
snd_pcm_oss 46368 0
snd_mixer_oss 16896 2 snd_pcm_oss
snd_pcm 79880 2 snd_als4000,snd_pcm_oss
snd_page_alloc 10248 1 snd_pcm
snd_opl3_lib 10112 1 snd_als4000
snd_timer 22660 2 snd_pcm,snd_opl3_lib
snd_hwdep 8864 1 snd_opl3_lib
snd_mpu401_uart 7296 1 snd_als4000
snd_rawmidi 23328 1 snd_mpu401_uart
snd_seq_device 8204 2 snd_opl3_lib,snd_rawmidi
ide_floppy 17408 0
snd 50276 13 snd_als4000,snd_sb_common,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_timer,snd_hwdep,snd_mpu 401_uart,snd_rawmidi,snd_seq_device
soundcore 9568 2 snd
intel_agp 21276 1
agpgart 31816 9 drm,sworks_agp,amd_k7_agp,ali_agp,sis_agp,ati_agp,nvidia_agp,via_agp,intel_agp
shpchp 40384 0
pci_hotplug 26164 1 shpchp
uhci_hcd 29328 0
i2c_piix4 8464 0
i2c_core 19984 1 i2c_piix4
aic7xxx 129588 2
scsi_transport_spi2 21120 1 aic7xxx
evdev 9088 3
root@1[~]# dmesg
[17179569.184000] Linux version 2.6.15-25-386 (root@mepis-party) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Mon Jun 19 00:05:53 EDT 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 512MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 131072
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000] Normal zone: 126976 pages, LIFO batch:31
[17179569.184000] HighMem zone: 0 pages, LIFO batch:0
[17179569.184000] DMI 2.1 present.
[17179569.184000] ACPI: Unable to locate RSDP
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda1 nomce quiet vga=791
[17179569.184000] Found and enabled local APIC!
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[ 0.000000] Detected 501.214 MHz processor.
[ 60.899779] Using tsc for high-res timesource
[ 60.899855] Console: colour dummy device 80x25
[ 60.902083] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 60.905103] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 60.969621] Memory: 514724k/524288k available (2633k kernel code, 9128k reserved, 929k data, 192k init, 0k highmem)
[ 60.969636] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 61.047140] Calibrating delay using timer specific routine.. 1003.75 BogoMIPS (lpj=2007509)
[ 61.047257] Security Framework v1.0.0 initialized
[ 61.047275] SELinux: Disabled at boot.
[ 61.047286] Capability LSM initialized
[ 61.047338] Mount-cache hash table entries: 512
[ 61.047667] CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
[ 61.047693] CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
[ 61.047724] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 61.047735] CPU: L2 cache: 512K
[ 61.047744] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
[ 61.047800] mtrr: v2.0 (20020519)
[ 61.047815] CPU: Intel Pentium III (Katmai) stepping 03
[ 61.047829] Enabling fast FPU save and restore... done.
[ 61.047838] Enabling unmasked SIMD FPU exception support... done.
[ 61.047852] Checking 'hlt' instruction... OK.
[ 61.171992] NET: Registered protocol family 16
[ 61.172404] PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=1
[ 61.172424] PCI: Using configuration type 1
[ 61.173711] ACPI: Subsystem revision 20051216
[ 61.173721] ACPI: Interpreter disabled.
[ 61.173732] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 61.173758] pnp: PnP ACPI: disabled
[ 61.173773] PnPBIOS: Scanning system for PnP BIOS support...
[ 61.173823] PnPBIOS: Found PnP BIOS installation structure at 0xc00f7540
[ 61.173837] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x68f4, dseg 0xf0000
[ 61.175656] PnPBIOS: Missing SMALL_TAG_ENDDEP tag
[ 61.175858] PnPBIOS: Missing SMALL_TAG_ENDDEP tag
[ 61.176025] PnPBIOS: Missing SMALL_TAG_ENDDEP tag
[ 61.176170] PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
[ 61.176582] SCSI subsystem initialized
[ 61.176751] usbcore: registered new driver usbfs
[ 61.176913] usbcore: registered new driver hub
[ 61.177111] PCI: Probing PCI hardware
[ 61.177126] PCI: Probing PCI hardware (bus 00)
[ 61.177614] PCI quirk: region 0400-043f claimed by PIIX4 ACPI
[ 61.177627] PCI quirk: region 0440-044f claimed by PIIX4 SMB
[ 61.177640] PIIX4 devres B PIO at 0290-0297
[ 61.178081] Boot video device is 0000:01:00.0
[ 61.184791] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 61.184807] pnp: 00:08: ioport range 0xcf8-0xcff could not be reserved
[ 61.184824] pnp: 00:09: ioport range 0x290-0x297 has been reserved
[ 61.185698] PCI: Bridge: 0000:00:01.0
[ 61.185710] IO window: d000-dfff
[ 61.185723] MEM window: ff900000-ff9fffff
[ 61.185735] PREFETCH window: eea00000-f6afffff
[ 61.186072] Machine check exception polling timer started.
[ 61.189996] audit: initializing netlink socket (disabled)
[ 61.190028] audit(1156588920.388:1): initialized
[ 61.190411] VFS: Disk quotas dquot_6.5.1
[ 61.190478] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 61.190705] squashfs: version 3.0prerelease (2006/1/24) Phillip Lougher
[ 61.190817] NTFS driver 2.1.25 [Flags: R/W].
[ 61.190883] Registering unionfs 1.1.2
[ 61.191017] Initializing Cryptographic API
[ 61.191033] io scheduler noop registered
[ 61.191058] io scheduler anticipatory registered
[ 61.191083] io scheduler deadline registered
[ 61.191179] io scheduler cfq registered
[ 61.191193] Limiting direct PCI/PCI transfers.
[ 61.191738] vesafb: framebuffer at 0xf0000000, mapped to 0xe0880000, using 3072k, total 16384k
[ 61.191755] vesafb: mode is 1024x768x16, linelength=2048, pages=9
[ 61.191766] vesafb: protected mode interface info at c000:4c03
[ 61.191775] vesafb: scrolling: redraw
[ 61.191788] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 61.191800] vesafb: Mode is VGA compatible
[ 61.267780] Console: switching to colour frame buffer device 128x48
[ 61.267800] fb0: VESA VGA frame buffer device
[ 61.268135] isapnp: Scanning for PnP cards...
[ 61.579553] isapnp: No Plug & Play device found
[ 61.655461] Non-volatile memory driver v1.2
[ 61.655876] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 61.655889] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 61.658270] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 61.658503] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 61.658693] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 61.658959] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 61.667886] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 61.670110] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 61.671112] loop: loaded (max 8 devices)
[ 61.671441] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 61.671456] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 61.671634] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 61.671673] PIIX4: chipset revision 1
[ 61.671681] PIIX4: not 100% native mode: will probe irqs later
[ 61.671706] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
[ 61.671743] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
[ 61.671772] Probing IDE interface ide0...
[ 61.959174] hda: Maxtor 90845D4, ATA DISK drive
[ 62.631222] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 62.631403] Probing IDE interface ide1...
[ 63.367010] hdc: Pioneer DVD-ROM ATAPIModel DVD-115 0111, ATAPI CD/DVD-ROM drive
[ 64.151008] hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
[ 64.207287] ide1 at 0x170-0x177,0x376 on irq 15
[ 64.210722] hda: max request size: 128KiB
[ 64.217188] hda: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=16383/16/63, UDMA(33)
[ 64.217209] hda: cache flushes not supported
[ 64.217380] hda: hda1 hda2 hda3
[ 64.245673] hdc: ATAPI DVD-ROM drive, 512kB Cache, UDMA(33)
[ 64.245695] Uniform CD-ROM driver Revision: 3.20
[ 64.247770] libata version 1.20 loaded.
[ 64.249458] Driver 'sd' needs updating - please use bus_type methods
[ 64.249747] ieee1394: Initialized config rom entry `ip1394'
[ 64.250026] ieee1394: raw1394: /dev/raw1394 device initialized
[ 64.250147] sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
[ 64.250160] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[ 64.250170] ieee1394: sbp2: Try serialize_io=0 for better performance
[ 64.250280] usbmon: debugfs is not available
[ 64.250400] Initializing USB Mass Storage driver...
[ 64.250513] usbcore: registered new driver usb-storage
[ 64.250525] USB Mass Storage support registered.
[ 64.250739] mice: PS/2 mouse device common for all mice
[ 64.250976] NET: Registered protocol family 2
[ 64.286941] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 64.287806] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
[ 64.289994] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 64.291447] TCP: Hash tables configured (established 131072 bind 65536)
[ 64.291460] TCP reno registered
[ 64.291812] ip_tables: (C) 2000-2002 Netfilter core team
[ 64.326779] TCP bic registered
[ 64.326827] NET: Registered protocol family 1
[ 64.326855] NET: Registered protocol family 8
[ 64.326864] NET: Registered protocol family 20
[ 64.326940] Using IPI Shortcut mode
[ 64.386175] EXT3-fs: mounted filesystem with ordered data mode.
[ 64.386229] VFS: Mounted root (ext3 filesystem) readonly.
[ 64.386425] Freeing unused kernel memory: 192k freed
[ 64.387320] kjournald starting. Commit interval 5 seconds
[ 65.757347] EXT3 FS on hda1, internal journal
[ 75.396693] Adding 787176k swap on /dev/hda2. Priority:1 extents:1 across:787176k
[ 77.804810] EXT3 FS on hda1, internal journal
[ 85.562664] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 85.653432] USB Universal Host Controller Interface driver v2.3
[ 85.653623] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 85.654329] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 85.654359] uhci_hcd 0000:00:07.2: irq 9, io base 0x0000ef80
[ 85.654827] hub 1-0:1.0: USB hub found
[ 85.654864] hub 1-0:1.0: 2 ports detected
[ 85.912531] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 85.990060] Linux agpgart interface v0.101 (c) Dave Jones
[ 85.996268] usb 1-2: new full speed USB device using uhci_hcd and address 2
[ 86.056688] agpgart: Detected an Intel 440BX Chipset.
[ 86.063445] agpgart: AGP aperture is 64M @ 0xf8000000
[ 86.132590] hub 1-2:1.0: USB hub found
[ 86.134451] hub 1-2:1.0: 4 ports detected
[ 86.445243] usb 1-2.1: new low speed USB device using uhci_hcd and address 3
[ 86.476890] ide-floppy driver 0.99.newide
[ 86.525098] hdd: No disk in drive
[ 86.573692] hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
[ 86.785122] usb 1-2.2: new low speed USB device using uhci_hcd and address 4
[ 87.125008] usb 1-2.3: new low speed USB device using uhci_hcd and address 5
[ 87.298255] Real Time Clock Driver v1.12
[ 87.557958] 8139too Fast Ethernet driver 0.9.27
[ 87.560002] eth0: RealTek RTL8139 at 0xe0c64f00, 00:40:f4:eb:89:2b, IRQ 10
[ 87.560014] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 87.816808] hdd: No disk in drive
[ 88.701545] input: PC Speaker as /class/input/input0
[ 88.760728] hdd: No disk in drive
[ 89.009419] parport: PnPBIOS parport detected.
[ 89.009486] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 89.037976] Floppy drive(s): fd0 is 1.44M
[ 89.055173] FDC 0 is a National Semiconductor PC87306
[ 100.514554] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 100.514563] <Adaptec 2940 Ultra SCSI adapter>
[ 100.514569] aic7880: Single Channel A, SCSI Id=7, 16/253 SCBs
[ 100.514576]
[ 100.781781] Vendor: Quantum Model: XP32150 Rev: 576D
[ 100.781824] Type: Direct-Access ANSI SCSI revision: 02
[ 100.781857] scsi0:A:1:0: Tagged Queuing enabled. Depth 8
[ 100.781896] target0:0:1: Beginning Domain Validation
[ 100.785785] target0:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 100.788107] target0:0:1: Domain Validation skipping write tests
[ 100.788119] target0:0:1: Ending Domain Validation
[ 100.790680] SCSI device sda: 4199760 512-byte hdwr sectors (2150 MB)
[ 100.791769] SCSI device sda: drive cache: write back
[ 100.793020] SCSI device sda: 4199760 512-byte hdwr sectors (2150 MB)
[ 100.794111] SCSI device sda: drive cache: write back
[ 100.794124] sda: sda1 sda2
[ 100.808418] sd 0:0:1:0: Attached scsi disk sda
[ 100.809498] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 100.816693] Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.05
[ 100.816733] Type: CD-ROM ANSI SCSI revision: 02
[ 100.816779] target0:0:2: Beginning Domain Validation
[ 100.818859] target0:0:2: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 100.820215] target0:0:2: Domain Validation skipping write tests
[ 100.820227] target0:0:2: Ending Domain Validation
[ 100.826055] sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 100.826675] sr 0:0:2:0: Attached scsi CD-ROM sr0
[ 100.827825] sr 0:0:2:0: Attached scsi generic sg1 type 5
[ 101.893081] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 101.964992] lp0: using parport0 (interrupt-driven).
[ 101.981969] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[ 103.991005] usbcore: registered new driver hiddev
[ 104.012605] input: USB-compliant keyboard as /class/input/input1
[ 104.012786] input: USB HID v1.10 Keyboard [USB-compliant keyboard] on usb-0000:00:07.2-2.1
[ 104.037536] input: USB-compliant keyboard as /class/input/input2
[ 104.037696] input: USB HID v1.10 Device [USB-compliant keyboard] on usb-0000:00:07.2-2.1
[ 104.378018] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 105.504759] NET: Registered protocol family 17
[ 114.054785] drivers/usb/input/hid-core.c: timeout initializing reports
[ 114.054796]
[ 114.055408] input: Logitech Inc. iFeel MouseMan as /class/input/input3
[ 114.056252] input: USB HID v1.00 Mouse [Logitech Inc. iFeel MouseMan] on usb-0000:00:07.2-2.2
[ 114.077337] input: Justcom Technology USB KVM Switch as /class/input/input4
[ 114.077765] input: USB HID v1.10 Keyboard [Justcom Technology USB KVM Switch] on usb-0000:00:07.2-2.3
[ 114.096285] input: Justcom Technology USB KVM Switch as /class/input/input5
[ 114.097206] input: USB HID v1.10 Mouse [Justcom Technology USB KVM Switch] on usb-0000:00:07.2-2.3
[ 114.097240] usbcore: registered new driver usbhid
[ 114.097250] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 116.256789] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 116.256803] md: bitmap version 4.39
[ 117.064783] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 117.575562] cdrom: open failed.
[ 118.121270] hdd: No disk in drive
[ 119.103514] powernow: This module only works with AMD K7 CPUs
[ 119.465829] ndiswrapper version 1.8 loaded (preempt=yes,smp=no)
[ 119.609373] usbcore: registered new driver ndiswrapper
[ 121.904102] kjournald starting. Commit interval 5 seconds
[ 121.904933] EXT3 FS on hda3, internal journal
[ 121.904951] EXT3-fs: mounted filesystem with ordered data mode.
[ 123.336226] Netfilter messages via NETLINK v0.30.
[ 123.397257] ip_conntrack version 2.4 (4096 buckets, 32768 max) - 232 bytes per conntrack
[ 138.996056] ppdev: user-space parallel port driver
[ 151.935930] powernow: This module only works with AMD K7 CPUs
[ 152.631070] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 162.117607] [drm] Initialized drm 1.0.1 20051102
[ 162.143389] [drm] Initialized r128 2.5.0 20030725 on minor 0
[ 162.146448] agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
[ 162.146483] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 162.146522] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 277.787680] sr 0:0:2:0: Device not ready.
[ 278.381045] (scsi0:A:2:0): No or incomplete CDB sent to device.
[ 278.381168] scsi0: Issued Channel A Bus Reset. 1 SCBs aborted
[ 278.643698] sr 0:0:2:0: SCSI error: return code = 0x10000
[ 278.730972] target0:0:2: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 709.126960] ABORTED IN=eth0 OUT= MAC=00:40:f4:eb:89:2b:02:0d:3a:6f:c3:91:08:00 SRC=66.102.7.104 DST=192.168.2.51 LEN=40 TOS=0x00 PREC=0x20 TTL=239 ID=4179 PROTO=TCP SPT=80 DPT=5677 SEQ=2818511404 ACK=2747308803 WINDOW=9300 RES=0x00 RST URGP=0
[ 1099.074764] ABORTED IN=eth0 OUT= MAC=00:40:f4:eb:89:2b:02:0d:3a:6f:c3:91:08:00 SRC=66.102.7.104 DST=192.168.2.51 LEN=40 TOS=0x00 PREC=0x20 TTL=239 ID=40835 PROTO=TCP SPT=80 DPT=5743 SEQ=1905185317 ACK=3173681561 WINDOW=9300 RES=0x00 RST URGP=0
[ 1175.025877] cdrom: open failed.
[ 1176.535423] cdrom: open failed.
root@1[~]#

My version of K3b is 0.12.14 Using KDE 3.5.3

I believe it was included in the MEPIS Distro.

The reason I had created the mount point in /media/ That is where the ISA CD was mounted and that was found by K3b.

Brian1 08-26-2006 11:46 AM
I have the feeling it is the K3B version you have. 0.12.17.1 is out. Download the source from K3B site and do a build and install of that.

Extract the source file
./configure
make
su to root
make install

Brian1

KornFused 08-26-2006 06:39 PM
I looked for it at K3b but didn't find it please forward URL.

KornFused 08-26-2006 08:11 PM
I looked at the K3b site, but could ot find the source for the version you referenced. I found it listed, but no download for Ubantu. Is there another program that you might recomend?

Brian1 08-27-2006 11:57 AM
They have it but I forgot it was not listed. Use the link
http://prdownloads.sourceforge.net/k...or=superb-east
and change to
http://prdownloads.sourceforge.net/k...or=superb-east

There is a scsi patch but have not found a link to it yet.
Here is the k3b-0.12-scsi.patch. Save to a file and apply before running make.
Code:
Skip scsi detection. Patch ported to 0.12 from FC development.

Mihai Maties <mihai@xcyb.org> - Fri Jun 17 11:52:18 EEST 2005

diff -Nur k3b-0.12.orig/libk3bdevice/k3bdevicemanager.cpp k3b-0.12/libk3bdevice/k3bdevicemanager.cpp
--- k3b-0.12.orig/libk3bdevice/k3bdevicemanager.cpp        2005-06-15 10:00:36.832920712 +0300
+++ k3b-0.12/libk3bdevice/k3bdevicemanager.cpp        2005-06-15 13:52:23.552777944 +0300
@@ -698,7 +698,8 @@
  }
 
  int bus = -1, target = -1, lun = -1;
-  bool scsi = determineBusIdLun( resolved, bus, target, lun );
+//  bool scsi = determineBusIdLun( resolved, bus, target, lun );
+  bool scsi = false;
  if(scsi) {
    if ( K3bDevice::Device* oldDev = findDevice(bus, target, lun) ) {
      kdDebug() << "(K3bDevice::DeviceManager) dev " << resolved  << " already found" << endl;
I would try the build without the patch first. I myself am a Redhat / Redhat clone distro user and build rpm packages so no help on Ubuntu packages.

Brian1

KornFused 08-29-2006 06:41 PM
Need for instructions
 
Brian,

I suffered a complete system crash and had to re-load MEPIS. Everything is back to where it was. I have never done a build and install before so I am in need of detailed instructions so if you can walk me through this it will be greatly appreciated.

I have downloaded K3b 12.17.1 and extracted it to /Home/Steve/Shared.

I have also removed the installed version of K3b from my computer. I don't know if this was necessary, but this way I know what I install will be the newer version.:newbie:


All times are GMT -5. The time now is 08:16 AM.