modem problems...
hello,
(sorry for my bad english.) i have a sony vaio PCG-GRX616MP laptop and i am trying to install my modem on a debian (knoppix) linux system (version 2.4.19-xfs). my modem is the Conextant-Ambit SoftK56 Data,Fax ICH Modem 8086:2486 but all i do ... the modem does not work. i read the articles in this forum and found many persons, who habe the same problem as i. but no tip worked. i did the following steps: at first i downloaded the hsflinmodem-5.03.27lnxbeta03042700.tar driver from the homepage www.linuxant.com (HSF (softmodem) driver) then i installed the driver with 'make install' and then with 'hsfconfig'. after that i changed the county to GERMANY with 'hsfconfig --country'. then i started 'modconf'. i changed into 'misc' and loaded the module 'hsfengine'. then i loaded the module 'hsfserial'. after that the following lines are written in /var/log/syslog: May 10 19:02:48 laptop insmod: Warning: loading /lib/modules/2.4.19-xfs/misc/hsfich.o will taint the kernel: non-GPL license - Copyright (C) 1996-2001 Conexant Systems Inc. All Rights Reserved. May 10 19:02:48 laptop insmod: See http://www.tux.org/lkml/#export-tainted for information about tainted modules May 10 19:02:48 laptop insmod: Module hsfich loaded, with warnings May 10 19:02:49 laptop kernel: PCI: No IRQ known for interrupt pin B of device 00:1f.6. Please try using pci=biosirq. May 10 19:02:49 laptop kernel: PCI: Setting latency timer of device 00:1f.6 to 64 May 10 19:02:49 laptop kernel: LinuxHookInterrupt: request for IRQ 0 failed May 10 19:02:49 laptop kernel: hsf_request_port: open failed then i run a few commands: root@laptop:~# lspci 00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04) 00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) 00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) 00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) 00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02) 00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) 00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) 00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus (rev 02) 00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02) 00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem (rev 02) 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW 02:05.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a 02:05.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a 02:05.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller 02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) Chipset Ethernet Controller (rev 42) root@laptop:~# lsmod Module Size Used by Tainted: P hsfich 95340 0 (autoclean) hsfserial 22484 0 (unused) hsfengine 869324 0 [hsfserial] hsfosspec 22204 0 [hsfich hsfserial hsfengine] lvm-mod 60768 0 (autoclean) ds 6472 4 rtc 6908 0 apm 9644 1 yenta_socket 8704 2 pcmcia_core 37536 0 [ds yenta_socket] usb-uhci 21612 0 (unused) usbmouse 1752 0 (unused) hid 19172 0 (unused) usbcore 56736 1 [usb-uhci usbmouse hid] mousedev 3832 1 input 3200 0 [usbmouse hid mousedev] serial 51908 0 i810_rng 2660 0 (unused) ... i could find the follwing lines in /etc/modules.conf ### update-modules: start processing /etc/modutils/hsf alias /dev/ttySHSF0 hsfserial alias char-major-240 hsfserial alias /dev/ttyCUA* hsfserial alias char-major-241 hsfserial alias /dev/modem hsfserial options hsfserial serialmajor=240 calloutmajor=241 ### update-modules: end processing /etc/modutils/hsf the link /dev/modem is there and the file ttySHSF0, too: root@laptop:/dev# ls -l ttyS* crw-rw-rw- 1 root dialout 4, 64 May 10 18:11 ttyS0 crw-rw-rw- 1 root dialout 4, 65 May 14 2002 ttyS1 crw-rw-rw- 1 root dialout 4, 66 Apr 15 2001 ttyS2 crw-rw-rw- 1 root dialout 4, 67 Apr 15 2001 ttyS3 crw-rw-rw- 1 root root 240, 64 May 10 17:56 ttySHSF0 now i configured the ppp conection 'provider' with pppconfig In pppconfig i used the link /dev/modem after running 'pon' the following lines are written in /var/log/syslog May 10 19:14:00 laptop kernel: CSLIP: code copyright 1989 Regents of the University of California May 10 19:14:00 laptop kernel: PPP generic driver version 2.4.2 May 10 19:14:00 laptop pppd[2543]: pppd 2.4.1 started by root, uid 0 May 10 19:14:01 laptop chat[2544]: Can't get terminal parameters: Input/output error May 10 19:14:01 laptop pppd[2543]: Connect script failed May 10 19:14:02 laptop pppd[2543]: Exit. now i read in an article, that i should try the boot command 'pci=biosirq' on the lili promt. but that did not work. still the same problems. then i tried the boot command 'pci=acpi'. still the same problems. here is my lili.conf (without the two boot commands): boot=/dev/hda3 vga=791 prompt timeout=50 append = "hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off noapic" image=/boot/vmlinuz-2.4.19-xfs label=knoppix root=/dev/hda3 read-only #other=/dev/hda1 # label=freedos # table=/dev/hda here the data from the modem with the listmodem programm: Build Number : 2600 ===================================================================== = RESULT OF MODEM QUERY = ===================================================================== NUMBER OF MODEMS FOUND = 1 MODEM #1: PCI CONFIGURATION INFORMATION READ: VENDOR ID : 8086 DEVICE ID : 2486 SUBVENDOR ID : 104D SUBDEVICE ID : 80FA REVISION ID : 02 DEDUCED INFORMATION: VENDOR NAME : UNKNOWN DEVICE NAME : UNKNOWN SUBVENDOR NAME : UNKNOWN MODEM TYPE : HSF WINXP INBUILD SUPPORT : NO what can i do to solve these problems? what can i do to bring the modem installed correctly? can anyone help me ? thanks ! _________________ Uli |
Oh.. I have similar problem with u... T.T I didn't solve that Problem yet... Did u??
|
All times are GMT -5. The time now is 08:11 PM. |