| ashryalls |
03-06-2005 04:24 PM |
mandrake 10.1 official hates my usb adsl modem
I have a turbocomm ea900 usb adsl modem, sometimes called a DSL-W ea900. The modem lights turn green, but stay solid green (as if it's frozen) and the modem isn't recognised. After much googling i've found it uses the Alcatel dynamite chipset. Based on this i found the zyxel driver (sourceforge.net/projects/zyxel630-11), but being new to linux couldn't get that to work. I'm pretty sure it uses PPPoA.
Any help on this matter is appreciated.
using:
Mandrake 10.1 official
kernel: 2.6.8.1-12mdksmp
dmesg:
Code:
0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Built 1 zonelists
Initializing CPU#0
Kernel command line: BOOT_IMAGE=linux ro root=1605 acpi=ht resume=/dev/hdc7 spla
sh=silent
bootsplash: silent mode.
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 2405.634 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254220k/262080k available (1963k kernel code, 7124k reserved, 869k data,
216k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4767.74 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
init init/main.c:689
init init/main.c:702
CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
per-CPU timeslice cutoff: 1463.08 usecs.
task migration cache decay timeout: 2 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4800.51 BogoMIPS
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Total of 2 processors activated (9568.25 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-5, 2-9, 2-10, 2-11, 2-17, 2-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178014
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0014
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 001 01 0 0 0 0 0 1 1 41
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 49
07 001 01 0 0 0 0 0 1 1 51
08 001 01 0 0 0 0 0 1 1 59
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 61
0d 001 01 0 0 0 0 0 1 1 69
0e 001 01 0 0 0 0 0 1 1 71
0f 001 01 0 0 0 0 0 1 1 79
10 001 01 1 1 0 1 0 1 1 81
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 89
13 001 01 1 1 0 1 0 1 1 91
14 001 01 1 1 0 1 0 1 1 99
15 001 01 1 1 0 1 0 1 1 A1
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 A9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2405.0119 MHz.
..... host bus clock speed is 200.0426 MHz.
checking TSC synchronization across 2 CPUs: passed.
init init/main.c:707
do_pre_smp_initcalls init/main.c:653
do_pre_smp_initcalls init/main.c:659
init init/main.c:711
init init/main.c:714
Brought up 2 CPUs
init init/main.c:716
CPU0: online
domain 0: span 00000003
groups: 00000001 00000002
CPU1: online
domain 0: span 00000003
groups: 00000002 00000001
init init/main.c:718
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
ACPI: Looking for DSDT in initrd ... not found!
Freeing initrd memory: 172k freed
init init/main.c:724
do_basic_setup init/main.c:634
do_basic_setup init/main.c:636
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb920, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
PCI: Using IRQ router SIS [1039/0963] at 0000:00:02.0
PCI->APIC IRQ transform: (B0,I2,P1) -> 18
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I2,P2) -> 18
PCI->APIC IRQ transform: (B0,I3,P0) -> 20
PCI->APIC IRQ transform: (B0,I3,P1) -> 21
PCI->APIC IRQ transform: (B0,I3,P3) -> 23
PCI->APIC IRQ transform: (B0,I4,P0) -> 19
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
vesafb: framebuffer at 0xd8000000, mapped to 0xd0800000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:f880
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Starting balanced_irq
audit: initializing netlink socket (disabled)
audit(1110149463.4294967142:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size 14554 bytes
, found (800x600, 14506 bytes, v3).
Console: switching to colour frame buffer device 92x32
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: CW088D ATAPI CD-R/RW, ATAPI CD/DVD-ROM drive
hdb: ATAPI 52X CDROM, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST360021A, ATA DISK drive
hdd: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
init init/main.c:726
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 216k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem d09e5000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: irq 21, pci mem d09e7000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: irq 23, pci mem d09f2000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ohci_hcd 0000:00:03.0: wakeup
ohci_hcd 0000:00:03.1: wakeup
usb 1-1: new full speed USB device using address 2
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 pr
oto 2 vid 0x04B8 pid 0x0005
usb 1-2: new full speed USB device using address 3
usb 2-1: new full speed USB device using address 2
EXT3 FS on hdc5, internal journal
Adding 465844k swap on /dev/hdc7. Priority:-1 extents:1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 648 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 128M @ 0xd0000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
NTFS driver 2.1.15 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
loop: loaded (max 8 devices)
hda: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
sis900.c: v1.08.07 11/02/2003
eth0: Unknown PHY transceiver found at address 0.
eth0: Realtek RTL8201 PHY transceiver found at address 1.
eth0: Unknown PHY transceiver found at address 2.
eth0: Unknown PHY transceiver found at address 3.
eth0: Unknown PHY transceiver found at address 4.
eth0: Unknown PHY transceiver found at address 5.
eth0: Unknown PHY transceiver found at address 6.
eth0: Unknown PHY transceiver found at address 7.
eth0: Unknown PHY transceiver found at address 8.
eth0: Unknown PHY transceiver found at address 10.
eth0: Unknown PHY transceiver found at address 11.
eth0: Unknown PHY transceiver found at address 13.
eth0: Unknown PHY transceiver found at address 14.
eth0: Unknown PHY transceiver found at address 15.
eth0: Unknown PHY transceiver found at address 16.
eth0: Unknown PHY transceiver found at address 17.
eth0: Unknown PHY transceiver found at address 18.
eth0: Unknown PHY transceiver found at address 19.
eth0: Unknown PHY transceiver found at address 20.
eth0: Unknown PHY transceiver found at address 21.
eth0: Unknown PHY transceiver found at address 22.
eth0: Unknown PHY transceiver found at address 23.
eth0: Unknown PHY transceiver found at address 24.
eth0: Unknown PHY transceiver found at address 25.
eth0: Unknown PHY transceiver found at address 26.
eth0: Unknown PHY transceiver found at address 27.
eth0: Unknown PHY transceiver found at address 28.
eth0: Unknown PHY transceiver found at address 29.
eth0: Unknown PHY transceiver found at address 30.
eth0: Unknown PHY transceiver found at address 31.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xe400, IRQ 19, 00:0d:87:15:ef:cb.
bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size 14554 bytes
, found (800x600, 14506 bytes, v3).
bootsplash: status on console 0 changed to on
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 332 bytes per conntrack
inserting floppy driver for 2.6.8.1-12mdksmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
eth0: Media Link Off
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 332 bytes per conntrack
intel8x0_measure_ac97_clock: measured 49561 usecs
intel8x0: clocking to 48000
Bluetooth: Core ver 2.6
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.3
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0342740(lo)
IPv6 over IPv4 tunneling driver
mtrr: 0xd8000000,0x8000000 overlaps existing 0xd8000000,0x100000
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
eth0: no IPv6 routers present
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377 bytes , v3).
bootsplash: status on console 5 changed to on
|
