LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (https://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   lsi 1068e, disk dropping (https://www.linuxquestions.org/questions/linux-hardware-18/lsi-1068e-disk-dropping-4175527395/)

kiwifruktish 12-05-2014 12:21 AM
lsi 1068e, disk dropping
 
I cant fingure out my problem, disk keeps droping from my lsi 1068e card :( and almost broke my raid6 configuration.

Strange part is as soon as the disk drops they will reapare.

Here is my info:
Distributor ID: Debian
Description: Debian GNU/Linux 7.2 (wheezy)
Release: 7.2
Codename: wheezy


Here is information from syslog:
Code:
Dec  4 18:37:21 LinuxX kernel: [104319.537398] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
Dec  4 18:37:26 LinuxX kernel: [104323.951433]  end_device-4:8: mptsas: ioc1: removing sata device: fw_channel 0, fw_id 13, phy 2,sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:37:26 LinuxX kernel: [104323.951439]  phy-4:2: mptsas: ioc1: delete phy 2, phy-obj (0xffff8800373b2400)
Dec  4 18:37:26 LinuxX kernel: [104323.951449]  port-4:8: mptsas: ioc1: delete port 8, sas_addr (0xdd5f3d43c2a49e7f)
Dec  4 18:37:26 LinuxX kernel: [104323.952086] sd 4:0:8:0: [sdr] Synchronizing SCSI cache
Dec  4 18:37:26 LinuxX kernel: [104323.952193] sd 4:0:8:0: [sdr]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:37:26 LinuxX kernel: [104323.952279] scsi target4:0:8: mptsas: ioc1: delete device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:37:54 LinuxX kernel: [104352.024931] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:37:54 LinuxX kernel: [104352.037384] scsi 4:0:9:0: Direct-Access    ATA      WDC WD20EARS-00S 0A80 PQ: 0 ANSI: 5
Dec  4 18:37:54 LinuxX kernel: [104352.039178] sd 4:0:9:0: Attached scsi generic sg12 type 0
Dec  4 18:37:54 LinuxX kernel: [104352.040162] sd 4:0:9:0: [sdl] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Dec  4 18:37:54 LinuxX kernel: [104352.069608] sd 4:0:9:0: [sdl] Write Protect is off
Dec  4 18:37:54 LinuxX kernel: [104352.069613] sd 4:0:9:0: [sdl] Mode Sense: 73 00 00 08
Dec  4 18:37:54 LinuxX kernel: [104352.081222] sd 4:0:9:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec  4 18:37:54 LinuxX kernel: [104352.133673]  sdl:
Dec  4 18:37:54 LinuxX kernel: [104352.197300] sd 4:0:9:0: [sdl] Attached SCSI disk
Dec  4 18:38:25 LinuxX kernel: [104382.539445] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
Dec  4 18:38:29 LinuxX kernel: [104386.804706]  end_device-4:9: mptsas: ioc1: removing sata device: fw_channel 0, fw_id 13, phy 2,sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:38:29 LinuxX kernel: [104386.804709]  phy-4:2: mptsas: ioc1: delete phy 2, phy-obj (0xffff8800373b2400)
Dec  4 18:38:29 LinuxX kernel: [104386.804715]  port-4:9: mptsas: ioc1: delete port 9, sas_addr (0xdd5f3d43c2a49e7f)
Dec  4 18:38:29 LinuxX kernel: [104386.805155] sd 4:0:9:0: [sdl] Synchronizing SCSI cache
Dec  4 18:38:29 LinuxX kernel: [104386.805180] sd 4:0:9:0: [sdl]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:38:29 LinuxX kernel: [104386.805219] scsi target4:0:9: mptsas: ioc1: delete device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:38:34 LinuxX kernel: [104391.676303] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:38:34 LinuxX kernel: [104391.688477] scsi 4:0:10:0: Direct-Access    ATA      WDC WD20EARS-00S 0A80 PQ: 0 ANSI: 5
Dec  4 18:38:34 LinuxX kernel: [104391.690350] sd 4:0:10:0: Attached scsi generic sg12 type 0
Dec  4 18:38:34 LinuxX kernel: [104391.691273] sd 4:0:10:0: [sdl] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Dec  4 18:38:34 LinuxX kernel: [104391.720740] sd 4:0:10:0: [sdl] Write Protect is off
Dec  4 18:38:34 LinuxX kernel: [104391.720745] sd 4:0:10:0: [sdl] Mode Sense: 73 00 00 08
Dec  4 18:38:34 LinuxX kernel: [104391.732301] sd 4:0:10:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec  4 18:38:34 LinuxX kernel: [104391.788240]  sdl:
Dec  4 18:38:34 LinuxX kernel: [104391.852270] sd 4:0:10:0: [sdl] Attached SCSI disk
Dec  4 18:39:59 LinuxX kernel: [104476.850893] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
Dec  4 18:40:00 LinuxX kernel: [104478.117232]  end_device-4:10: mptsas: ioc1: removing sata device: fw_channel 0, fw_id 13, phy 2,sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:40:00 LinuxX kernel: [104478.117238]  phy-4:2: mptsas: ioc1: delete phy 2, phy-obj (0xffff8800373b2400)
Dec  4 18:40:00 LinuxX kernel: [104478.117248]  port-4:10: mptsas: ioc1: delete port 10, sas_addr (0xdd5f3d43c2a49e7f)
Dec  4 18:40:00 LinuxX kernel: [104478.118042] sd 4:0:10:0: [sdl] Synchronizing SCSI cache
Dec  4 18:40:00 LinuxX kernel: [104478.118092] sd 4:0:10:0: [sdl]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:00 LinuxX kernel: [104478.118142] scsi target4:0:10: mptsas: ioc1: delete device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:40:01 LinuxX /USR/SBIN/CRON[29561]: (root) CMD (vnstat -u -i eth0 >> /dev/null 2>&1)
Dec  4 18:40:03 LinuxX kernel: [104481.088104] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.088273] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.088456] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.088643] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.088828] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.089008] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:03 LinuxX kernel: [104481.089199] mptbase: ioc1: LogInfo(0x31110d00): Originator={PL}, Code={Reset}, SubCode(0x0d00) cb_idx mptscsih_io_done
Dec  4 18:40:04 LinuxX kernel: [104481.586951] mptbase: ioc1: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet Executed}, SubCode(0x0000) cb_idx mptscsih_io_done
Dec  4 18:40:04 LinuxX kernel: [104481.586986] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.586991] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.587004] sd 4:0:3:0: [sdm] CDB: Write(10): 2a 00 00 00 00 08 00 00 01 00
Dec  4 18:40:04 LinuxX kernel: [104481.587130] end_request: I/O error, dev sdm, sector 8
Dec  4 18:40:04 LinuxX kernel: [104481.587198] md: super_written gets error=-5, uptodate=0
Dec  4 18:40:04 LinuxX kernel: [104481.587203] md/raid:md1: Disk failure on sdm, disabling device.
Dec  4 18:40:04 LinuxX kernel: [104481.587204] md/raid:md1: Operation continuing on 8 devices.
Dec  4 18:40:04 LinuxX kernel: [104481.589342]  end_device-4:3: mptsas: ioc1: removing sata device: fw_channel 0, fw_id 14, phy 3,sas_addr 0x1f605d2e6d7e4c4e
Dec  4 18:40:04 LinuxX kernel: [104481.589350]  phy-4:3: mptsas: ioc1: delete phy 3, phy-obj (0xffff8800373ae400)
Dec  4 18:40:04 LinuxX kernel: [104481.589361]  port-4:3: mptsas: ioc1: delete port 3, sas_addr (0x1f605d2e6d7e4c4e)
Dec  4 18:40:04 LinuxX kernel: [104481.589412] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589414] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.589416] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 5c 00
Dec  4 18:40:04 LinuxX kernel: [104481.589419] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589421] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.589423] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 5c 00 00 03 e0 00
Dec  4 18:40:04 LinuxX kernel: [104481.589428] end_request: I/O error, dev sdm, sector 3022478336
Dec  4 18:40:04 LinuxX kernel: [104481.589430] md/raid:md1: read error not correctable (sector 3022478336 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589432] md/raid:md1: read error not correctable (sector 3022478344 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589433] md/raid:md1: read error not correctable (sector 3022478352 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589435] md/raid:md1: read error not correctable (sector 3022478360 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589436] md/raid:md1: read error not correctable (sector 3022478368 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589438] md/raid:md1: read error not correctable (sector 3022478376 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589439] md/raid:md1: read error not correctable (sector 3022478384 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589440] md/raid:md1: read error not correctable (sector 3022478392 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589442] md/raid:md1: read error not correctable (sector 3022478400 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589443] md/raid:md1: read error not correctable (sector 3022478408 on sdm).
Dec  4 18:40:04 LinuxX kernel: [104481.589469]  00 04 00 00
Dec  4 18:40:04 LinuxX kernel: [104481.589471] end_request: I/O error, dev sdm, sector 3022478336
Dec  4 18:40:04 LinuxX kernel: [104481.589482] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589483] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.589484] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 5f e0 00 00 20 00
Dec  4 18:40:04 LinuxX kernel: [104481.589487] end_request: I/O error, dev sdm, sector 3022479328
Dec  4 18:40:04 LinuxX kernel: [104481.589492] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589493] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.589494] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 60 00 00 00 e8 00
Dec  4 18:40:04 LinuxX kernel: [104481.589497] end_request: I/O error, dev sdm, sector 3022479360
Dec  4 18:40:04 LinuxX kernel: [104481.589512] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589513] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:04 LinuxX kernel: [104481.589514] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 60 e8 00 02 18 00
Dec  4 18:40:04 LinuxX kernel: [104481.589516] end_request: I/O error, dev sdm, sector 3022479592
Dec  4 18:40:04 LinuxX kernel: [104481.589550] sd 4:0:3:0: [sdm] Unhandled error code
Dec  4 18:40:04 LinuxX kernel: [104481.589552] sd 4:0:3:0: [sdm] CDB: Read(10): 28 00 b4 27 63 00 00 01 00 00
Dec  4 18:40:04 LinuxX kernel: [104481.589554] end_request: I/O error, dev sdm, sector 3022480128
Dec  4 18:40:04 LinuxX kernel: [104481.590033] sd 4:0:3:0: [sdm] Synchronizing SCSI cache
Dec  4 18:40:04 LinuxX kernel: [104481.590051] sd 4:0:3:0: [sdm]  Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Dec  4 18:40:07 LinuxX kernel: [104484.679312] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 13, phy 2, sas_addr 0xdd5f3d43c2a49e7f
Dec  4 18:40:07 LinuxX kernel: [104484.691777] scsi 4:0:11:0: Direct-Access    ATA      WDC WD20EARS-00S 0A80 PQ: 0 ANSI: 5
Dec  4 18:40:07 LinuxX kernel: [104484.693618] sd 4:0:11:0: Attached scsi generic sg12 type 0
Dec  4 18:40:07 LinuxX kernel: [104484.695022] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 14, phy 3, sas_addr 0x1f605d2e6d7e4c4e
Dec  4 18:40:07 LinuxX kernel: [104484.695805] sd 4:0:11:0: [sdl] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Dec  4 18:40:07 LinuxX kernel: [104484.697678] scsi 4:0:12:0: Direct-Access    ATA      ST2000DL003-9VT1 CC32 PQ: 0 ANSI: 5
Dec  4 18:40:07 LinuxX kernel: [104484.699516] sd 4:0:12:0: Attached scsi generic sg13 type 0
Dec  4 18:40:07 LinuxX kernel: [104484.700626] sd 4:0:12:0: [sdr] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Dec  4 18:40:07 LinuxX kernel: [104484.725479] sd 4:0:11:0: [sdl] Write Protect is off
Dec  4 18:40:07 LinuxX kernel: [104484.725483] sd 4:0:11:0: [sdl] Mode Sense: 73 00 00 08
Dec  4 18:40:07 LinuxX kernel: [104484.737176] sd 4:0:11:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec  4 18:40:07 LinuxX kernel: [104484.754716] sd 4:0:12:0: [sdr] Write Protect is off
Dec  4 18:40:07 LinuxX kernel: [104484.754720] sd 4:0:12:0: [sdr] Mode Sense: 73 00 00 08
Dec  4 18:40:07 LinuxX kernel: [104484.766438] sd 4:0:12:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Dec  4 18:40:07 LinuxX kernel: [104484.787173]  sdl:
Dec  4 18:40:07 LinuxX kernel: [104484.844149]  sdr:
Dec  4 18:40:07 LinuxX kernel: [104484.851102] sd 4:0:11:0: [sdl] Attached SCSI disk
Dec  4 18:40:07 LinuxX kernel: [104484.918884] sd 4:0:12:0: [sdr] Attached SCSI disk
I have also read on some sites problems with lsi 1068e and smartd? as i said i dont know why this happends. i have more this and this only have happend to the disk that are connected to the lsi 1068e not to the other controllors. i am aslo way under when using power from the psu so power is not the problem.

smallpond 12-06-2014 07:31 AM
Are you running smartd? Make sure you don't run the periodic self tests on the disks. That can cause timeouts.

kiwifruktish 12-06-2014 12:16 PM
You mean to turn off smartd? So i dont run it on the disk connected to the card.

kiwifruktish 12-09-2014 02:10 AM
After waking up i understood "periodic" i have turned any thing off that could spin up the disk.

And for now it working as it should, i will report back if somethign happens ;)

Thanks for the help


All times are GMT -5. The time now is 02:37 AM.