LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices


Reply
  Search this Thread
Old 08-15-2007, 02:28 AM   #1
yvlasenko
LQ Newbie
 
Registered: Aug 2007
Posts: 1

Rep: Reputation: 0
Infortrend ES A24U-G2421-1 + Adaptec 29320A vs Gentoo


Hi everybody!

I was trying to connect Infortrend external raid to linux box, but system doesn't see any drives.

It's my first expirience with scsi so any help would be appriciated.

Raid is configured as 8x raid5 (3 drives each, 24 total).

This is part of my dmesg:

Quote:
localhost ~ # dmesg | grep scsi
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
scsi0:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
scsi0: Dumping Card State at program address 0x161 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x1ba, DINDEX = 0x1b8
scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
scsi0:A:0:0: Target did not send an IDENTIFY message. LASTPHASE = 0x40.
scsi0: Issued Channel A Bus Reset. 1 SCBs aborted
scsi0: Unexpected PKT busfree condition
scsi0: Dumping Card State at program address 0x1b2 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x106, DINDEX = 0x106
scsi0: SCBPTR == 0x3, SCB_NEXT == 0xff00, SCB_NEXT2 == 0xff6f
scsi 0:0:2:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x 0
scsi0: At time of recovery, card was not paused
scsi0: Dumping Card State at program address 0x3 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x106, DINDEX = 0x106
scsi0: SCBPTR == 0x3, SCB_NEXT == 0xff00, SCB_NEXT2 == 0xff6f
scsi 0:0:2:0: Unable to deliver message
scsi0: Command abort returning 0x2003
scsi 0:0:2:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0 x24 0x0
scsi0: Device reset code sleeping
(scsi0:A:2:0): Bus Device Reset Message Sent
scsi0: device overrun (status 9) on 0:2:0
scsi0: Device reset returning 0x2002
scsi0:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
scsi0: Dumping Card State at program address 0x161 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x1ba, DINDEX = 0x1b8
scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
scsi0:A:0:0: Target did not send an IDENTIFY message. LASTPHASE = 0xc0.
scsi0:A:0:0: Protocol violation in Status phase. Attempting to abort.
scsi0:A:0:0: Abort for unidentified connection completed.
scsi 0:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi0: At time of recovery, card was not paused
scsi0: Dumping Card State at program address 0x31 Mode 0x11
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0x3, SINDEX = 0x1ff, DINDEX = 0x1b8
scsi0: SCBPTR == 0x3, SCB_NEXT == 0xffc0, SCB_NEXT2 == 0xff79
(scsi0:A:2:0): Device is disconnected, re-queuing SCB
scsi0: Recovery code sleeping
(scsi0:A:2:0): Abort Message Sent
(scsi0:A:2:0): SCB 3 - Abort Tag Completed.
scsi0: device overrun (status 9) on 0:2:0
scsi0:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
scsi0: Dumping Card State at program address 0x161 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x1ba, DINDEX = 0x1b8
scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
scsi0:A:0:0: Target did not send an IDENTIFY message. LASTPHASE = 0xc0.
scsi0:A:0:0: Protocol violation in Status phase. Attempting to abort.
scsi0:A:0:0: Abort for unidentified connection completed.
scsi 0:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi0: At time of recovery, card was not paused
scsi0: Dumping Card State at program address 0x18 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x1ff, DINDEX = 0x1b8
scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
(scsi0:A:2:0): Device is disconnected, re-queuing SCB
scsi0: Recovery code sleeping
(scsi0:A:2:0): Abort Message Sent
(scsi0:A:2:0): SCB 3 - Abort Tag Completed.
scsi0: device overrun (status 9) on 0:2:0
scsi 0:0:2:0: scsi: Device offlined - not ready after error recovery
scsi0:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
scsi0: Dumping Card State at program address 0x161 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x1ba, DINDEX = 0x1b8
scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
scsi0:A:0:0: Target did not send an IDENTIFY message. LASTPHASE = 0x40.
scsi0: Issued Channel A Bus Reset. 1 SCBs aborted
scsi0: Unexpected PKT busfree condition
scsi0: Dumping Card State at program address 0x1b2 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x10a, DINDEX = 0x10a
scsi0: SCBPTR == 0x3, SCB_NEXT == 0xff80, SCB_NEXT2 == 0xff79
scsi 0:0:4:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x 0
scsi0: At time of recovery, card was not paused
scsi0: Dumping Card State at program address 0x18 Mode 0x33
scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
scsi0: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
scsi0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
scsi0: REG0 == 0xff00, SINDEX = 0x10a, DINDEX = 0x10a
scsi0: SCBPTR == 0x3, SCB_NEXT == 0xff80, SCB_NEXT2 == 0xff79
scsi 0:0:4:0: Unable to deliver message
scsi0: Command abort returning 0x2003
scsi 0:0:4:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0 x24 0x0
scsi0: Device reset code sleeping
(scsi0:A:4:0): Bus Device Reset Message Sent
scsi0: device overrun (status 9) on 0:4:0
scsi0: Device reset returning 0x2002
scsi1 : ata_piix
scsi2 : ata_pii
If anything else would help - just let me know please.
 
Old 12-04-2007, 07:44 AM   #2
wally.nl
LQ Newbie
 
Registered: Nov 2005
Location: Netherlands
Posts: 3

Rep: Reputation: 0
Question Did you fix it ?

We're having the same issue, have you been able to determine the cause and fix it ? We're using an onboard adaptec 79xx & infortrend A16U raid cabinet.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
Gentoo live cd will not mount /dev/hdc on HP Omnibook xe3 (Gentoo 2006.0.0) tommygoober Linux - Software 3 03-16-2007 06:51 AM
Adaptec 29320A alfcup Linux - Hardware 7 07-21-2005 05:18 PM
Adaptec 29320A-R SCSI controller: Slack 10.1 ok? svar Slackware 6 06-10-2005 02:24 AM
Gentoo AMD64 Kernel 2.6.xx Adaptec aacraid hanging solved!!! PriceComparison Linux - Hardware 1 04-12-2005 04:05 AM
Dual boot w/ Gentoo/xp pro vs. gentoo-invalid partition table bobbear Linux - Software 3 02-10-2004 04:28 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware

All times are GMT -5. The time now is 11:12 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration