LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (https://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   Freezing Mouse (https://www.linuxquestions.org/questions/linux-hardware-18/freezing-mouse-207742/)

subh 07-21-2004 02:40 AM

Freezing Mouse
 
Hi there,
I am using xandros open circulation desktop version 2.0. Everything works fine while installing. But after first boot, the mouse get frozen. It does not move at all. I have reconfigured xserver-xfree86. But no result.
I am also running "debain sarge" in one of my hard disk partition. I have no problem reconfiguring xserver.
But I have failed always with "XANDROS". I am using "usb optical wheel mouse".
I am attaching the "dmesg" & "xf86config-4".


er: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 04
per-CPU timeslice cutoff: 1462.49 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-9, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1816.2694 MHz.
..... host bus clock speed is 100.9038 MHz.
cpu: 0, clocks: 1009038, slice: 504519
CPU0<T0:1009024,T1:504496,D:9,S:504519,C:1009038>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
ACPI: Subsystem revision 20031002
PCI: PCI BIOS revision 2.10 entry at 0xf1580, last bus=1
PCI: Using configuration type 1
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xa9 -> IRQ 20 Mode:1 Active:1)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xb1 -> IRQ 23 Mode:1 Active:1)
00:00:02[A] -> 2-23 -> IRQ 23
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22 Mode:1 Active:1)
00:00:02[B] -> 2-22 -> IRQ 22
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc1 -> IRQ 21 Mode:1 Active:1)
00:00:02[C] -> 2-21 -> IRQ 21
Pin 2-22 already programmed
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc9 -> IRQ 16 Mode:1 Active:1)
00:00:08[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xd1 -> IRQ 17 Mode:1 Active:1)
00:00:08[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xd9 -> IRQ 18 Mode:1 Active:1)
00:00:08[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xe1 -> IRQ 19 Mode:1 Active:1)
00:00:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178000
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0000
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 000 00 1 0 0 0 0 0 0 00
0a 001 01 0 0 0 0 0 1 1 71
0b 001 01 0 0 0 0 0 1 1 79
0c 001 01 0 0 0 0 0 1 1 81
0d 001 01 0 0 0 0 0 1 1 89
0e 001 01 0 0 0 0 0 1 1 91
0f 001 01 0 0 0 0 0 1 1 99
10 001 01 1 1 0 1 0 1 1 C9
11 001 01 1 1 0 1 0 1 1 D1
12 001 01 1 1 0 1 0 1 1 D9
13 001 01 1 1 0 1 0 1 1 E1
14 001 01 0 1 0 1 0 1 1 A9
15 001 01 1 1 0 1 0 1 1 C1
16 001 01 1 1 0 1 0 1 1 B9
17 001 01 1 1 0 1 0 1 1 B1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:20
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 961 MuTIOL IDE UDMA100 controller
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST380023A, ATA DISK drive
hdb: ST340016A, ATA DISK drive
blk: queue c033dca0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c033dde8, I/O limit 4095Mb (mask 0xffffffff)
hdc: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive
hdd: LG DVD-ROM DRD-8160B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 >
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 >
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 144k freed
VFS: Mounted root (minix filesystem).
Mounted devfs on /dev
SFX: Splash Parms at 0x5C0
SFX: Here we go!
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,16)) ...
for (ide0(3,16))
ide0(3,16):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Adding Swap: 497968k swap-space (priority -1)
Adding Swap: 500428k swap-space (priority -2)
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
inserting floppy driver for 2.4.24-x1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
eth0: NatSemi DP8381[56] at 0xf89b6000, 00:09:5b:1e:21:2d, IRQ 16.
ohci1394: $Rev: 1045 $ Ben Collins <bcollins@debian.org>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[e2800000-e28007ff] Max Packet=[2048]
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-RW DVR-106D Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Vendor: LG Model: DVD-ROM DRD8160B Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0151026580]
usb-ohci.c: USB OHCI at membase 0xf89f8000, IRQ 20
usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xf89fa000, IRQ 23
usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
eth0: autonegotiation did not complete in 4000 usec.
hub.c: new USB device 00:02.2-2, assigned address 2
input: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse OpticalŪ] on usb1:2.0
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,15), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,11), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,70), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,12), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbdevfs: remount parameter error
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbmouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
PROMISE FastTrak TX4000/376/378/S150 TX Series Linux Driver Version 1.00.0.19
ft3xx: No valid controller detected
PROMISE FastTrak TX4000/376/378/S150 TX Series Linux Driver Version 1.00.0.19
ft3xx: No valid controller detected
PROMISE FastTrak TX4000/376/378/S150 TX Series Linux Driver Version 1.00.0.19
ft3xx: No valid controller detected
PROMISE FastTrak TX4000/376/378/S150 TX Series Linux Driver Version 1.00.0.19
ft3xx: No valid controller detected
attempt to access beyond end of device
03:0b: rw=0, want=2359308, limit=96358
EXT3-fs error (device ide0(3,11)): ext3_get_inode_loc: unable to read inode block - inode=587521, block=589826
attempt to access beyond end of device
03:0b: rw=0, want=15335436, limit=96358
EXT3-fs error (device ide0(3,11)): ext3_get_inode_loc: unable to read inode block - inode=3818881, block=3833858
sh-2021: reiserfs_read_super: can not find reiserfs on ide0(3,13)
VFS: Can't find ext3 filesystem on dev ide0(3,13).
VFS: Can't find ext2 filesystem on dev ide0(3,13).
FAT: bogus logical sector size 34015
VFS: Can't find a valid FAT filesystem on dev 03:0d.
FAT: bogus logical sector size 34015
VFS: Can't find a valid FAT filesystem on dev 03:0d.
VFS: Can't find a Minix or Minix V2 filesystem on device 03:0d.
Unable to identify CD-ROM format.
EXT3-fs error (device ide0(3,65)): ext3_check_descriptors: Block bitmap for group 64 not in group (block 8191)!
EXT3-fs: group descriptors corrupted !
sh-2021: reiserfs_read_super: can not find reiserfs on ide0(3,65)
EXT3-fs error (device ide0(3,65)): ext3_check_descriptors: Block bitmap for group 64 not in group (block 8191)!
EXT3-fs: group descriptors corrupted !
EXT2-fs: ide0(3,65): couldn't mount because of unsupported optional features (4).
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:41.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:41.
VFS: Can't find a Minix or Minix V2 filesystem on device 03:41.
Unable to identify CD-ROM format.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
eth0: remaining active for wake-on-lan
eth0: autonegotiation did not complete in 4000 usec.
usb-uhci.c: $Revision: 1.275 $ time 17:07:46 Feb 20 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: Detected SiS 645 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: overridden by ACPI.
0: nvidia: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-5336 Wed Jan 14 18:29:26 PST 2004
devfs_register(nvidiactl): could not append to parent, err: -17
devfs_register(nvidia0): could not append to parent, err: -17
eth0: remaining active for wake-on-lan
eth0: autonegotiation did not complete in 4000 usec.






################################################################################
## Automatically generated file by buildxconf
## part of the Xandros hardware detection system
##
## See Also:
## 'man devices-overview' for information about the detection system
## 'man setxconf' a utility for interacting with the detection system
## to modify the X configuration
## 'man XF86Config' for the format of this file
##
## Warning:
## If this file is edited manually, then buildxconf will no longer
## modify this file. It must be removed to be regenerated.
################################################################################


Section "Files"
ModulePath "/usr/X11R6/lib/modules/nvidia"
ModulePath "/usr/X11R6/lib/modules/altdrivers"
ModulePath "/usr/X11R6/lib/modules"

# Local Fontserver: Disabled by default.
#FontPath "unix/:7100"

# Unscaled Bitmap Fonts:
FontPath "/usr/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/lib/X11/fonts/100dpi:unscaled"

# Scalable TrueType and CID Fonts (via DeFoMa):
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"

# Scalable TrueType Fonts (via std X path):
FontPath "/usr/lib/X11/fonts/TrueType"

# Scalable Speedo and Type1 Fonts:
FontPath "/usr/lib/X11/fonts/Type1"
FontPath "/usr/lib/X11/fonts/Speedo"

# Scaled Bitmap fonts (ugly) :
FontPath "/usr/lib/X11/fonts/100dpi"
FontPath "/usr/lib/X11/fonts/75dpi"
FontPath "/usr/lib/X11/fonts/misc"
FontPath "/usr/lib/X11/fonts/cyrillic"

# Misc. Fonts:
FontPath "/usr/share/fonts"
EndSection

Section "Module"
Load "ddc"
Load "dbe"
Load "extmod"
Load "glx"
Load "record"
Load "bitmap"
Load "freetype"
Load "speedo"
Load "type1"
Load "vbe"
Load "int10"
Load "xandetect"
EndSection

Section "InputDevice"
Identifier "Keyboard1"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
EndSection

Section "InputDevice"
Identifier "mouse.usb"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/misc/psaux"
Option "Protocol" "IMPS/2"
Option "Emulate3Buttons" "NO"
Option "ZAxisMapping" "4 5"
EndSection

Section "DRI"
Mode 0666
EndSection

# extra options in [video.1] extension = yes
# pci info: 0x10DE, 0x110, 0x100
# extra options in [video.1] VideoRam = 65536k
# extra options in [video.1] Xmodules = -dri -GLcore
Section "Device"
Identifier "Device1"
Driver "nvidia"
Option "NoRenderAccel"
BusID "PCI:1:0:0"
Screen 0
EndSection

Section "Monitor"
Identifier "Monitor1"
VendorName "DEL"
ModelName "DELL M770"
HorizSync 30-69
Option "DPMS"
EndSection

# res 1024 768
Section "Screen"
Identifier "Screen1"
Device "Device1"
Monitor "Monitor1"
DefaultDepth 16
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "ServerFlags"
AllowMouseOpenFail
EndSection

Section "ServerLayout"
Identifier "Default Layout"
Screen "Screen1"
InputDevice "Keyboard1"
InputDevice "mouse.usb"
EndSection

Frustin 07-21-2004 03:07 AM

you should change the line:

Option "Device" "/dev/misc/psaux"

to

Option "Device" "/dev/input/mice"

subh 07-21-2004 04:42 AM

I have tried changing from "Option "Device" "/dev/misc/psaux" to "Option "Device" "/dev/input/mice". But no luck.

Frustin 07-21-2004 04:59 AM

in that case i would suggest to you that you dont have usb mouse installed in your kernel.

subh 07-22-2004 07:52 AM

Mouse worked during install. But, It stopped working after First boot. I can see the mouse cursor. But it doesn't move.

Frustin 07-22-2004 07:55 AM

yes, the install cd has its own kernel independent of the one that now resides in /usr/src/linux and /boot.

subh 07-23-2004 03:09 AM

I really didn't understant what do you mean by "kernel independent". Could please explain.

Frustin 07-23-2004 03:17 AM

well when you booted using the CD you would have noticed that you get all the kernel messages before it went into the gui set up screen. That is a kernel booting, it will load all the drivers that you need to control stuff like the mouse and keyboard when you are running through the installation.

That kernel that is on the CD is _not_ the one that is installed to your system, vis it is independent.

Looking back at what i wrote it not particularly grammatically acturate so i understand your confusion. I should have put a comma after the word kernel. *wonders off to take 50 lashes*

emperorjordan 08-01-2004 08:27 PM

i am still a newbie when it comes to this stuff, but i had the same prob with xandros 2.0 (the pay version) the problem was the mouse. it was a plain white microsoft wheel mouse optical USB and it had the same symptoms you have. i tried it on my mandrake 9.2 rig, and every time i launch mandrake control center, same thing, the mouse freezes along with the control center, but i can still navigate the system with the keyboard. i suggest going out and buying a logitech mouse, i got one at staples for $14 and it has worked fine. i also have a rev 4 intellimouse USB, and that works fine with xandros........

Frustin 08-02-2004 03:25 AM

there is no need to be going out buying new mice. if you dont work these things out by looking at all the options, how are you going to learn linux?
emperorjordan, in your avatar you have distributions:
Xandros, Mandrake, FreeBSD and that you like to tinker. Dont you think that what you say in your avatar is a contridiction to what you said in your last post?

Explore all possiblilties. eliminate all the variables until you come to the last and no matter how unlikely that will be the answer. if you dont know how to elimiate those variable, there is _always_ someone whom has.


All times are GMT -5. The time now is 11:50 PM.