I have just successfully installed Red Hat Enterprise 4 Update 4 (2.6.9-42.ELsmp). Unfortunately the Asus DVD recorder drive is not recognised. It is not listed in /etc/fstab, /media, /dev
Things I should make you aware of-:
1. To install the OS I had to type the following at the boot prompt
linux all-generic-ide
2. The motherboard is a Gigabyte GA-965P-DQ6 (Rev 1.0) with a Intel ICH8R southbridge and a Gigabyte SATA 2 controller (JMicron).
3. Relevant BIOS settings
a) SATA Raid / AHCI is set to Disabled (Sets the onboard SATA controller to IDE mode). (Intel ICH8R controller only?)
b) SATA Port0-3 Native Mode is set to Disabled (Legacy IDE mode) (Intel ICH8R controller only?)
c) Onboard SATA/IDE Device - Enabled - This function allows users to enable or disable the SATA/IDE ports controlled by the Gigabyte SATA 2 controller
d) Onboard SATA/IDE Ctrl Mode - IDE - Set the SATA channel to IDE mode (Gigabyte SATA 2 controller)
4. The DVD drive is connected to the single IDE connector available on the motherboard.
5. The drive works fine in Windows and I managed to install Linux fine using the drive.
6. I have installed all available updates using the Red Hat Update Agent. The current Kernel is 2.6.9-42.0.10.ELsmp.
7. Output from /sbin/lspci follows
00:00.0 Host bridge: Intel Corporation P965/G965 Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation P965/G965 PCI Express Root Port (rev 02)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801H (ICH8 Family) 4 port SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation 82801H (ICH8 Family) 2 port SATA IDE Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation G70 [GeForce 7600 GT] (rev a1)
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 22)
04:00.0 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02)
05:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
8. Output from dmseg:-
Bootdata ok (command line is ro root=LABEL=/ rhgb quiet)
Linux version 2.6.9-42.0.10.ELsmp (brewbuilder@ls20-bc1-14.build.redhat.com) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Fri Feb 16 17:13:42 EST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable)
BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS)
BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data)
BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
ACPI: RSDP (v000 GBT ) @ 0x00000000000f6e90
ACPI: RSDT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x00000000dfee3040
ACPI: FADT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x00000000dfee30c0
ACPI: HPET (v001 GBT GBTUACPI 0x42302e31 GBTU 0x00000098) @ 0x00000000dfee7cc0
ACPI: MCFG (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x00000000dfee7d40
ACPI: MADT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x00000000dfee7bc0
ACPI: DSDT (v001 GBT GBTUACPI 0x00001000 MSFT 0x0100000c) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-0000000120000000
Bootmem setup node 0 0000000000000000-0000000120000000
No mptable found.
On node 0 totalpages: 1179648
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 1175552 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.4 present.
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
Setting APIC routing to flat
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at e0000000 (gap: dff00000:10100000)
Checking aperture...
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 14.318180 MHz HPET timer.
time.c: Detected 2133.338 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Placing software IO TLB between 0x1ca1000 - 0x5ca1000
Memory: 4043740k/4718592k available (2106k kernel code, 0k reserved, 1299k data, 196k init)
Calibrating delay using timer specific routine.. 4269.57 BogoMIPS (lpj=2134787)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
using mwait in idle threads.
CPU0: Physical Processor ID: 0
CPU0: Processor Core ID: 0
CPU0: Initial APIC ID: 0
Using IO APIC NMI watchdog
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU0: Physical Processor ID: 0
CPU0: Processor Core ID: 0
CPU0: Initial APIC ID: 0
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 02
per-CPU timeslice cutoff: 34.41 usecs.
task migration cache decay timeout: 1 msecs.
Booting processor 1/1 rip 6000 rsp 10005d55f58
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.65 BogoMIPS (lpj=2133329)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU1: Physical Processor ID: 0
CPU1: Processor Core ID: 1
CPU1: Initial APIC ID: 1
Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 02
Total of 2 processors activated (8536.23 BogoMIPS).
activating NMI Watchdog ... done.
testing NMI watchdog ... OK.
Using local APIC timer interrupts.
Detected 16.666 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
time.c: Using HPET/TSC based timekeeping.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
PCI: Using MMCONFIG at f0000000
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 177
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 185
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 169
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 201
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 217
ACPI: PCI interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 217
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 185
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1175688365.393:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 7800C0CB7E15BE48
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1, 2 throttling states)
ACPI: Processor [CPU1] (supports C1, 2 throttling states)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: ST3500641AS, ATA DISK drive
Probing IDE interface ide1...
hdc: ST3500641AS, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: Host Protected Area detected.
current capacity is 976771055 sectors (500106 MB)
native capacity is 976773168 sectors (500107 MB)
hda: 976771055 sectors (500106 MB) w/16384KiB Cache, CHS=60801/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: max request size: 1024KiB
hdc: 976773168 sectors (500107 MB) w/16384KiB Cache, CHS=60801/255/63
hdc: cache flushes supported
hdc: hdc1 hdc2
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 262144 (order: 10, 4194304 bytes)
TCP: Hash tables configured (established 262144 bind 262144)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
PCI0 PEX0 PEX1 PEX2 PEX3 PEX4 PEX5 HUB0 UAR1 IGBE USB0 USB1 USB2 USB3 US31 USB4 USBE USE2 AZAL
Freeing unused kernel memory: 196k freed
SCSI subsystem initialized
libata version 1.20 loaded.
ahci 0000:04:00.0: version 1.2
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 201
MSI INIT SUCCESS
PCI: Setting latency timer of device 0000:04:00.0 to 64
ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ata1: SATA max UDMA/133 cmd 0xFFFFFF0000004100 ctl 0x0 bmdma 0x0 irq 201
ata2: SATA max UDMA/133 cmd 0xFFFFFF0000004180 ctl 0x0 bmdma 0x0 irq 201
ata1: SATA link down (SStatus 0)
scsi0 : ahci
ata2: SATA link down (SStatus 0)
scsi1 : ahci
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 217
ata: 0x1f0 IDE port busy
ata: 0x170 IDE port busy
ata_piix: probe of 0000:00:1f.2 failed with error -16
ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xDC02 bmdma 0xE800 irq 217
ata4: SATA max UDMA/133 cmd 0xE000 ctl 0xE402 bmdma 0xE808 irq 217
ata3: SATA port has no device.
scsi2 : ata_piix
ata4: SATA port has no device.
scsi3 : ata_piix
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Losing some ticks... checking if CPU frequency changed.
warning: many lost ticks.
Your time source seems to be instable or some driver is hogging interupts
rip __do_softirq+0x4d/0xd0
Falling back to HPET
security: 3 users, 4 roles, 355 types, 26 bools
security: 55 classes, 22582 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hdc1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
inserting floppy driver for 2.6.9-42.0.10.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:03:00.0 to 64
sky2 v1.1 addr 0xf8000000 irq 169 Yukon-EC (0xb6) rev 2
divert: allocating divert_blk for eth0
sky2 eth0: addr 00:16:e6:d5:a5:a8
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hw_random: RNG not detected
ACPI: PCI interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 185
ehci_hcd 0000:00:1a.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: irq 185, pci mem ffffff0000002000
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 209, pci mem ffffff000005c000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1a.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: irq 169, io base 000000000000c000
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 177
uhci_hcd 0000:00:1a.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: irq 177, io base 000000000000c400
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
uhci_hcd 0000:00:1d.0: UHCI Host Controller
usb 1-1: new high speed USB device using address 2
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 209, io base 000000000000c800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
uhci_hcd 0000:00:1d.1: UHCI Host Controller
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 217, io base 000000000000cc00
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 185, io base 000000000000d000
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb 1-1.1: new high speed USB device using address 3
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
isa bounce pool size: 16 pages
Vendor: SMSC Model: USB 2 HS-CF Rev: 1.63
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi4, channel 0, id 0, lun 0
Vendor: SMSC Model: USB 2 HS-MS Rev: 1.63
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 1
Vendor: SMSC Model: USB 2 HS-SM Rev: 1.63
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi4, channel 0, id 0, lun 2
Vendor: SMSC Model: USB 2 HS-SD/MMC Rev: 1.63
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi4, channel 0, id 0, lun 3
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80405b40(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 1.0-9755 Mon Feb 26 23:16:31 PST 2007
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hdc1, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised:
dm-devel@redhat.com
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hdc2, type ext3), uses xattr
Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1
Adding 2048276k swap on /dev/hda3. Priority:-2 extents:1
Adding 2048248k swap on /dev/hda5. Priority:-3 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: No new microdata for cpu 0
microcode: No new microdata for cpu 1
IA-32 Microcode Update Driver v1.14 unregistered
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 456 bytes per conntrack
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
eth0: no IPv6 routers present
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
lp0: console ready
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Any help would be very much appreciated!
