Like this:
kernel /vmlinuz-2.4.20-8 ro root=LABEL=/ hdc=ide-scsi So what is the error? |
I added the line to etc/grub.conf
Below is the message I get from cdrecord Cdrecord 2.0 (i686-pc-linux-gnu) Copyright (C) 1995-2002 J?rg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 cdrecord: No such device. Cannot open '/dev/pg0'. Cannot open SCSI driver. cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you |
You need to reboot the computer for the grub changes to take effect.
Then try the command: cdrecord --scanbus Your CDRW drive should be displayed and hopefully you will be able to burn a CD. |
Quote:
/dev/sr0 /mnt/cdrom auto user,ro,noauto 0 0 |
I used Mike's suggestion and was able to see the device using cdrecord -scanbus. However, I am no longer able to run x cdroast. (There is no error, the program does not load). I also have Gnome toaster but am unable to get it working. Could be operator ignorance problem.
I'm away from the system. Will post dmesg when I return |
you assume that he is using grub with Red Hat 9.0, it is probably lilo, and he needs to edit lilo.conf
image=/boot/vmlinuz-2.4.20-8 label=linux initrd=/boot/initrd-2.4.20-8.img read-only append="root=LABEL=/" "hdd=ide-scsi" |
Quote:
|
I have lilo.conf.anaconda file
Here is my dmesg output (see multiple posts for entire output) entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09 per-CPU timeslice cutoff: 1462.89 usecs. task migration cache decay timeout: 10 msecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000040 ESR value after enabling vector: 00000000 Error: only one processor found. WARNING: No sibling found for CPU 0. ENABLING IO-APIC IRQs Setting 8 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 8 ... ok. Setting 10 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 10 ... ok. Setting 9 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 9 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 8-0, 8-13, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15, 10-16, 10-17, 10-18, 10-19, 10-20, 10-21, 10-22, 10-23, 9-4, 9-5, 9-6, 9-7, 9-8, 9-9, 9-10, 9-11, 9-12, 9-13, 9-14, 9-15, 9-16, 9-17, 9-18, 9-19, 9-20, 9-21, 9-22, 9-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 46. number of IO-APIC #8 registers: 24. number of IO-APIC #10 registers: 24. number of IO-APIC #9 registers: 24. testing the IO APIC....................... IO APIC #8...... .... register #00: 08000000 ....... : physical APIC id: 08 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 0FF 0F 0 0 0 0 0 1 1 39 02 0FF 0F 0 0 0 0 0 1 1 31 03 0FF 0F 0 0 0 0 0 1 1 41 04 0FF 0F 0 0 0 0 0 1 1 49 05 0FF 0F 0 0 0 0 0 1 1 51 06 0FF 0F 0 0 0 0 0 1 1 59 07 0FF 0F 0 0 0 0 0 1 1 61 08 0FF 0F 0 0 0 0 0 1 1 69 09 0FF 0F 0 0 0 0 0 1 1 71 0a 0FF 0F 0 0 0 0 0 1 1 79 0b 0FF 0F 0 0 0 0 0 1 1 81 0c 0FF 0F 0 0 0 0 0 1 1 89 0d 000 00 1 0 0 0 0 0 0 00 0e 0FF 0F 0 0 0 0 0 1 1 91 0f 0FF 0F 0 0 0 0 0 1 1 99 10 0FF 0F 1 1 0 1 0 1 1 A1 11 0FF 0F 1 1 0 1 0 1 1 A9 12 0FF 0F 1 1 0 1 0 1 1 B1 13 0FF 0F 1 1 0 1 0 1 1 B9 14 0FF 0F 1 1 0 1 0 1 1 C1 15 0FF 0F 1 1 0 1 0 1 1 C9 16 0FF 0F 1 1 0 1 0 1 1 D1 17 0FF 0F 1 1 0 1 0 1 1 D9 |
dmesg post #2
IO APIC #10...... .... register #00: 0A000000 ....... : physical APIC id: 0A .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 0A000000 ....... : arbitration: 0A .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 0FF 0F 1 1 0 1 0 1 1 E1 01 0FF 0F 1 1 0 1 0 1 1 E9 02 0FF 0F 1 1 0 1 0 1 1 32 03 0FF 0F 1 1 0 1 0 1 1 3A 04 0FF 0F 1 1 0 1 0 1 1 42 05 0FF 0F 1 1 0 1 0 1 1 4A 06 0FF 0F 1 1 0 1 0 1 1 52 07 0FF 0F 1 1 0 1 0 1 1 5A 08 0FF 0F 1 1 0 1 0 1 1 62 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IO APIC #9...... .... register #00: 09000000 ....... : physical APIC id: 09 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 09000000 ....... : arbitration: 09 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 0FF 0F 1 1 0 1 0 1 1 6A 01 0FF 0F 1 1 0 1 0 1 1 72 02 0FF 0F 1 1 0 1 0 1 1 7A 03 0FF 0F 1 1 0 1 0 1 1 82 04 000 00 1 0 0 0 0 0 0 00 05 000 00 1 0 0 0 0 0 0 00 06 000 00 1 0 0 0 0 0 0 00 07 000 00 1 0 0 0 0 0 0 00 08 000 00 1 0 0 0 0 0 0 00 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ21 -> 0:21 IRQ22 -> 0:22 IRQ23 -> 0:23 IRQ24 -> 1:0 IRQ25 -> 1:1 IRQ26 -> 1:2 IRQ27 -> 1:3 IRQ28 -> 1:4 IRQ29 -> 1:5 IRQ30 -> 1:6 IRQ31 -> 1:7 IRQ32 -> 1:8 IRQ48 -> 2:0 IRQ49 -> 2:1 IRQ50 -> 2:2 IRQ51 -> 2:3 .................................... done. |
dmesg post #3
Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2392.3621 MHz. ..... host bus clock speed is 132.9089 MHz. cpu: 0, clocks: 1329089, slice: 664544 CPU0<T0:1329088,T1:664544,D:0,S:664544,C:1329089> Starting migration thread for cpu 0 smp_num_cpus: 1. PCI: PCI BIOS revision 2.10 entry at 0xfbdd5, last bus=5 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Ignoring BAR0-3 of IDE controller 00:1f.1 Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0 PCI->APIC IRQ transform: (B0,I29,P0) -> 16 PCI->APIC IRQ transform: (B0,I29,P1) -> 19 PCI->APIC IRQ transform: (B0,I29,P2) -> 18 PCI->APIC IRQ transform: (B0,I29,P3) -> 23 PCI->APIC IRQ transform: (B0,I31,P0) -> 18 PCI->APIC IRQ transform: (B0,I31,P1) -> 17 PCI->APIC IRQ transform: (B0,I31,P1) -> 17 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 PCI->APIC IRQ transform: (B3,I14,P0) -> 24 PCI->APIC IRQ transform: (B5,I12,P0) -> 20 PCI->APIC IRQ transform: (B5,I14,P0) -> 22 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Starting kswapd VFS: Disk quotas vdquot_6.5.1 pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS0 at 0x03f8 (irq = 4) is a 16550A ttyS1 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 NET4: Frame Diverter 0.46 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 00:1f.1 PCI: Enabling device 00:1f.1 (0005 -> 0007) ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hda: IC35L090AVV207-0, ATA DISK drive blk: queue c0459500, I/O limit 4095Mb (mask 0xffffffff) hdc: SONY CD-RW CRX216E, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 156250000 sectors (80000 MB) w/1821KiB Cache, CHS=9726/255/63, UDMA(100) ide-floppy driver 0.99.newide Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 > ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes |
dmesg post 4
TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 146k freed VFS: Mounted root (ext2 filesystem). Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 156k freed usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Setting latency timer of device 00:1d.7 to 64 ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller ehci-hcd 00:1d.7: irq 23, pci mem f084c800 usb.c: new USB bus registered, assigned bus number 1 ehci-hcd 00:1d.7: enabled 64bit PCI DMA PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:1d.7 PCI cache line size corrected to 128. ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22 hub.c: USB hub found hub.c: 6 ports detected usb-uhci.c: $Revision: 1.275 $ time 13:43:11 Dec 18 2003 usb-uhci.c: High bandwidth mode enabled PCI: Setting latency timer of device 00:1d.0 to 64 usb-uhci.c: USB UHCI at I/O 0xff80, IRQ 16 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.1 to 64 usb-uhci.c: USB UHCI at I/O 0xff60, IRQ 19 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.2 to 64 usb-uhci.c: USB UHCI at I/O 0xff40, IRQ 18 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 4 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal LVM version 1.0.5+(22/07/2002) module loaded loop: loaded (max 8 devices) Adding Swap: 522072k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal EXT3-fs: mounted filesystem with ordered data mode. ohci1394: $Rev: 693 $ Ben Collins <bcollins@debian.org> ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[fe1ff800-fe1fffff] Max Packet=[2048] ieee1394: SelfID completion called outside of bus reset! ieee1394: Host added: Node[00:1023] GUID[84ffffffffffff00] [Linux OHCI-1394] |
dmesg post 5 (last)
SCSI subsystem driver Revision: 1.00 hdc: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: SONY Model: CD-RW CRX216E Rev: PD01 Type: CD-ROM ANSI SCSI revision: 02 hdc: DMA disabled IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com> microcode: CPU0 no microcode found! (sig=f29, pflags=2) parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 12x/12x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (6139 buckets, 49112 max) - 292 bytes per conntrack i2c-core.o: i2c core module i2c-core.o: adapter Smbus i8254x at 03:0e.0 Int registered as adapter 0. i2c-core.o: adapter Smbus i8254x at 03:0e.0 Ext registered as adapter 1. Loading i8254x SMBus driver. Version 3.0.9 i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-dev.o: Registered 'Smbus i8254x at 03:0e.0 Int' as minor 0 i2c-dev.o: Registered 'Smbus i8254x at 03:0e.0 Ext' as minor 1 i2c-proc.o version 2.6.1 (20010825) Adding ASF alerting device watchdog driver.Version 3.0.6 i2c-core.o: driver ASF Alert device watchdog timer registered. asfwdg: Attaching adapter Smbus i8254x at 03:0e.0 Int i2c-core.o: client [ASF alert dev watchdog] registered to adapter [Smbus i8254x at 03:0e.0 Int](pos. 0). asfwdg: Attaching adapter Smbus i8254x at 03:0e.0 Ext i2c-core.o: client [ASF alert dev watchdog] registered to adapter [Smbus i8254x at 03:0e.0 Ext](pos. 0). Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 Copyright (c) 1999-2003 Intel Corporation. divert: allocating divert_blk for eth0 eth0: Intel(R) PRO/1000 Network Connection e1000: eth0 NIC Link is Up 100 Mbps Full Duplex Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002) divert: allocating divert_blk for eth1 eth1: ADMtek Comet rev 17 at 0xf09b8400, 00:0C:41:20:77:78, IRQ 22. parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected lp0: using parport0 (polling). lp0: console ready 0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4363 Sat Apr 19 17:46:46 PDT 2003 Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 690M agpgart: Unsupported Intel chipset (device id: 2550), you might want to try agp_try_unsupported=1. agpgart: no supported devices found. 0: NVRM: AGPGART: unable to retrieve symbol table cdrom: This disc doesn't have any tracks I recognize! |
This is the output from an attempt to write to data to CD
[root@pcp07744476pcs oracle]# cdrecord -v speed=4 dev=0,0, 0 -data number1.img Cdrecord 2.0 (i686-pc-linux-gnu) Copyright (C) 1995-2002 J ?rg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.24 Using libscg version 'schily-0.7' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'SONY ' Identifikation : 'CD-RW CRX216E ' Revision : 'PD01' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1895168 = 1850 KB FIFO size : 4194304 = 4096 KB Track 01: data 1016 MB Total size: 1167 MB (115:40.61) = 520546 sectors Lout start: 1167 MB (115:42/46) = 520546 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Is not unrestricted Is not erasable Disk sub type: Medium Type B, low Beta category (B-) (4) ATIP start of lead in: -12369 (97:17/06) ATIP start of lead out: 359849 (79:59/74) Disk type: Short strategy type (Phthalocyanine or simil ar) Manuf. index: 69 Manufacturer: Moser Baer India Limited Manufacturer is guessed because of the orange forum embarg o. The orange forum likes to get money for recent information . The information for this media may not be correct. Blocks total: 359849 Blocks current: 359326 Blocks remaini ng: -161220 cdrecord: WARNING: Data may not fit on current disk. cdrecord: Notice: Most recorders cannot write CD's >= 90 m inutes. cdrecord: Notice: Use -ignsize option to allow >= 90 minut es. cdrecord: Notice: Use -overburn option to write more than the official disk capacity. cdrecord: Notice: Most CD-writers do overburning only on S AO or RAW mode. [root@pcp07744476pcs oracle]# cdrecord -v -ignsize speed=4 dev=0,0,0 -data number1.img Cdrecord 2.0 (i686-pc-linux-gnu) Copyright (C) 1995-2002 J?rg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.24 Using libscg version 'schily-0.7' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'SONY ' Identifikation : 'CD-RW CRX216E ' Revision : 'PD01' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1895168 = 1850 KB FIFO size : 4194304 = 4096 KB Track 01: data 1016 MB Total size: 1167 MB (115:40.61) = 520546 sectors Lout start: 1167 MB (115:42/46) = 520546 sectors Current Secsize: 2048 See next post for more output |
continued
ATIP info from disk: Indicated writing power: 5 Is not unrestricted Is not erasable Disk sub type: Medium Type B, low Beta category (B-) (4) ATIP start of lead in: -12369 (97:17/06) ATIP start of lead out: 359849 (79:59/74) Disk type: Short strategy type (Phthalocyanine or similar) Manuf. index: 69 Manufacturer: Moser Baer India Limited Manufacturer is guessed because of the orange forum embargo. The orange forum likes to get money for recent information. The information for this media may not be correct. Blocks total: 359849 Blocks current: 359326 Blocks remaining: -161220 cdrecord: WARNING: Data may not fit on current disk. cdrecord: Notice: Overburning active. Trying to write more than the official disk capacity. Forcespeed is OFF. Starting to write CD/DVD at speed 4 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is ON. Turning BURN-Free off Performing OPC... Starting new track at sector: 523 Track 01: 0 of 1016 MB written.cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 02 0B 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.024s timeout 40s write track data: error after 0 bytes Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00 Writing time: 28.071s Average write speed 999.0x. Fixating... cdrecord: Input/output error. close track/session: scsi sendcmd: no error CDB: 5B 00 02 00 00 00 00 00 00 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 72 03 00 00 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x72 Qual 0x03 (session fixation error - incomplete track in session) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.000s timeout 480s cmd finished after 0.000s timeout 480s Fixating time: 0.004s cdrecord: fifo had 64 puts and 1 gets. cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%. |
CD RW Writing data to a CD
RH9 and two RW drives; one HP one Plextor. When I put a blank CDRW in either of my drives a window opens that is titled " burn:/// ". Then I drag and drop files and click on write CD. I think your RH9 should do the same. Did you leave anything out when you did the install?
|
All times are GMT -5. The time now is 11:46 AM. |