Hi.
I was trying to install ubuntu 20.04 on Adata NVME.
Tried with two usb sticks, several times downloaded image.
But installer crashed shorty later started copying files.
Previously had Fedora on it. Worked OK.
So, I made a new partition table and managed to install.
I have not noticed any problems so far.
Could you please check my smart and error log and advice if disk is OK.
Thank you
Code:
sudo smartctl -a /dev/nvme0n1
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-28-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Number: ADATA SX6000PNP
Serial Number: 2J3120017987
Firmware Version: V9001c19
PCI Vendor/Subsystem ID: 0x10ec
IEEE OUI Identifier: 0x00e04c
Controller ID: 1
Number of Namespaces: 1
Namespace 1 Size/Capacity: 256.060.514.304 [256 GB]
Namespace 1 Formatted LBA Size: 512
Namespace 1 IEEE EUI-64: 525433 334e333139
Local Time is: Sat May 2 15:11:12 2020 CEST
Firmware Updates (0x02): 1 Slot
Optional Admin Commands (0x0006): Format Frmw_DL
Optional NVM Commands (0x0014): DS_Mngmt Sav/Sel_Feat
Maximum Data Transfer Size: 32 Pages
Warning Comp. Temp. Threshold: 118 Celsius
Critical Comp. Temp. Threshold: 150 Celsius
Supported Power States
St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat
0 + 8.00W - - 0 0 0 0 0 0
1 + 4.00W - - 1 1 1 1 0 0
2 + 3.00W - - 2 2 2 2 0 0
3 - 0.0128W - - 3 3 3 3 4000 8000
4 - 0.0080W - - 4 4 4 4 8000 30000
Supported LBA Sizes (NSID 0x1)
Id Fmt Data Metadt Rel_Perf
0 + 512 0 0
=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
SMART/Health Information (NVMe Log 0x02)
Critical Warning: 0x00
Temperature: 32 Celsius
Available Spare: 100%
Available Spare Threshold: 32%
Percentage Used: 1%
Data Units Read: 4.837.675 [2,47 TB]
Data Units Written: 3.610.195 [1,84 TB]
Host Read Commands: 68.052.835
Host Write Commands: 34.125.037
Controller Busy Time: 0
Power Cycles: 347
Power On Hours: 106
Unsafe Shutdowns: 16
Media and Data Integrity Errors: 0
Error Information Log Entries: 0
Warning Comp. Temperature Time: 0
Critical Comp. Temperature Time: 0
Error Information (NVMe Log 0x01, max 8 entries)
Num ErrCount SQId CmdId Status PELoc LBA NSID VS
0 1 0 0x0000 0x0000 0x000 0 0 -
6 1219368206019409473 0 0x0000 0x0000 0x000 0 0 -
Code:
sudo nvme error-log /dev/nvme0n1
Error Log Entries for device:nvme0n1 entries:8
.................
Entry[ 0]
.................
error_count : 1
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 1]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 2]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 3]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 4]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 5]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 6]
.................
error_count : 1219368206019409473
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
Entry[ 7]
.................
error_count : 0
sqid : 0
cmdid : 0
status_field : 0(SUCCESS: The command completed successfully)
parm_err_loc : 0
lba : 0
nsid : 0
vs : 0
cs : 0
.................
