|
Monitoring Hardware Health: lm_sensors, smartd & apcupsd
Can someone tell me what this means? Is my hard drive about to fail or what? Also does any one know of a GUI based tool I can use with KDE to monitor S.M.A.R.T. in real time? Right now I have KSeonsors monitoring my fans/temp and APCUPSD monitoring my UPS. If you know of software with a GUI that can monitor all these devices in one program I'd like to know.
defiant:/home/njdube # smartctl -a /dev/sda smartctl version 5.37 [x86_64-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax 10 family (SATA/300) Device Model: Maxtor 6V200E0 Serial Number: V40F4VZG Firmware Version: VA111630 User Capacity: 203,928,109,056 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Tue Jun 5 21:30:02 2007 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 246) Self-test routine in progress... 60% of test remaining. Total time to complete Offline data collection: (4682) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 32 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 208 208 063 Pre-fail Always - 13066 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 373 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0 7 Seek_Error_Rate 0x000a 253 001 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 249 232 187 Pre-fail Always - 56268 9 Power_On_Hours 0x0032 251 251 000 Old_age Always - 987 10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 252 252 000 Old_age Always - 646 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 064 051 000 Old_age Always - 606142500 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 194 Temperature_Celsius 0x0032 033 253 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 583 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 0 202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0 210 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 211 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 212 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 54 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 54 occurred at disk power-on lifetime: 520 hours (21 days + 16 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 02 c9 5d 0e e0 at LBA = 0x000e5dc9 = 941513 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 ff 02 c9 5d 0e e0 00 00:33:56.719 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:56.642 READ DMA EXT 42 ff 02 c7 5d 0e e0 00 00:33:53.553 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:53.553 READ DMA EXT 42 ff 04 cb 5d 0e e0 00 00:33:53.444 READ VERIFY SECTOR(S) EXT Error 53 occurred at disk power-on lifetime: 520 hours (21 days + 16 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 04 cb 5d 0e e0 at LBA = 0x000e5dcb = 941515 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 ff 04 cb 5d 0e e0 00 00:33:53.444 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:53.367 READ DMA EXT 42 ff 04 c7 5d 0e e0 00 00:33:50.193 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:50.116 READ DMA EXT 42 ff 08 c7 5d 0e e0 00 00:33:47.027 READ VERIFY SECTOR(S) EXT Error 52 occurred at disk power-on lifetime: 520 hours (21 days + 16 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 04 c7 5d 0e e0 at LBA = 0x000e5dc7 = 941511 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 ff 04 c7 5d 0e e0 00 00:33:50.193 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:50.116 READ DMA EXT 42 ff 08 c7 5d 0e e0 00 00:33:47.027 READ VERIFY SECTOR(S) EXT 42 ff 08 bf 5d 0e e0 00 00:33:47.027 READ VERIFY SECTOR(S) EXT 42 ff 10 cf 5d 0e e0 00 00:33:46.918 READ VERIFY SECTOR(S) EXT Error 51 occurred at disk power-on lifetime: 520 hours (21 days + 16 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 10 cf 5d 0e e0 at LBA = 0x000e5dcf = 941519 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 ff 10 cf 5d 0e e0 00 00:33:46.918 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:46.841 READ DMA EXT 42 ff 10 bf 5d 0e e0 00 00:33:43.752 READ VERIFY SECTOR(S) EXT 25 ff 01 00 00 00 e0 00 00:33:43.752 READ DMA EXT 42 ff 20 df 5d 0e e0 00 00:33:43.642 READ VERIFY SECTOR(S) EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 105 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. defiant:/home/njdube # |
Here is my PATA drive. It seems to be working fine.
defiant:/home/njdube # smartctl -a /dev/hda smartctl version 5.37 [x86_64-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Western Digital Protege Device Model: WDC WD1200AB-22DYA0 Serial Number: WD-WMALC1054462 Firmware Version: 15.05R15 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Jun 5 21:42:38 2007 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (3796) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 53) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 152 145 021 Pre-fail Always - 2933 4 Start_Stop_Count 0x0032 099 099 040 Old_age Always - 1616 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 20994 10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1597 194 Temperature_Celsius 0x0022 118 253 000 Old_age Always - 32 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 0 199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 53 200 Multi_Zone_Error_Rate 0x0009 200 155 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 240 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. defiant:/home/njdube # |
Quick question! Are these normal temperatures for my system? System = 84F, AMD Sempron 2800+ = 88F, Power = 100F. I'll assume Power means the power supply. I noticed the power supply fan doesn't spin as fast as the system fans. Is that normal? Also, lm_sensors (as well as my boards BIOS) only detects the CPU and System fan. Is the power supply fan supposed to be detected at all? I get a temp reading from it, just not a fan reading.
|
| All times are GMT -5. The time now is 08:39 AM. |