anon133 |
08-02-2004 10:44 AM |
Then, dmesg:
Quote:
Linux version 2.6.7-gentoo-r11 (root@livecd) (gcc version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6)) #6 Sun Aug 1 17:01:49 UTC 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f6ba0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff79c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
Built 1 zonelists
Kernel command line: root=/dev/hde3
Initializing CPU#0
CPU 0 irqstacks, hard=c04de000 soft=c04dd000
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1830.209 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 515140k/524224k available (2776k kernel code, 8320k reserved, 1005k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3620.86 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2500+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18)
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APCE] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 5
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10
ACPI: PCI Interrupt Link [LAPU] enabled at IRQ 10
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
ACPI: PCI Interrupt Link [LFIR] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 5
PCI: Using ACPI for IRQ routing
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1091467444.319:0): initialized
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (42 C)
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS2++ Logitech MX Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
lp: driver loaded but no devices found
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hdc: AOPEN CD-RW CRW5224 1.08 20031030, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SiI3112 Serial ATA: IDE controller at PCI slot 0000:01:0b.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: 100% native mode on irq 11
ide2: MMIO-DMA , BIOS settings: hde:DMA, hdf:DMA
ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
hde: Maxtor 6Y080M0, ATA DISK drive
ide2 at 0xe0808080-0xe0808087,0xe080808a on irq 11
hdg: no response (status = 0xfe)
hdg: no response (status = 0xfe), resetting drive
hdg: no response (status = 0xfe)
hde: max request size: 64KiB
hde: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63
/dev/ide/host2/bus0/target0/lun0: p1 p2 p3
hdc: ATAPI 40X CD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.02 loaded.
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[e8084000-e80847ff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 11, pci mem e0822000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49455 usecs
intel8x0: clocking to 47477
ALSA device list:
#0: NVidia nForce2 at 0xe8081000, irq 11
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
ReiserFS: hde3: found reiserfs format "3.6" with standard journal
ohci1394: fw-host0: SelfID received outside of bus reset sequence
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000508df21175]
ReiserFS: hde3: using ordered data mode
ReiserFS: hde3: journal params: device hde3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hde3: checking transaction log (hde3)
ReiserFS: hde3: journal-1153: found in header: first_unflushed_offset 4611, last_flushed_trans_id 25225
ReiserFS: hde3: journal-1006: found valid transaction start offset 4611, len 10 id 25226
ReiserFS: hde3: journal-1206: Starting replay from offset 108344845013507, trans_id 1
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4611, len 10 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4623
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4623, len 14 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4639
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4639, len 17 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4658
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4658, len 1 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4661
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4661, len 21 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4684
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4684, len 48 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4734
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4734, len 12 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4748
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4748, len 91 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4841
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4841, len 36 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4879
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4879, len 40 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4921
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4921, len 36 mount_id 38
ReiserFS: hde3: journal-1095: setting journal start to offset 4959
ReiserFS: hde3: journal-1037: journal_read_transaction, offset 4959, len 131148 mount_id 140
ReiserFS: hde3: journal-1146: journal_read_trans skipping because 140 is != newest_mount_id 38
ReiserFS: hde3: journal-1299: Setting newest_mount_id to 39
ReiserFS: hde3: replayed 11 transactions in 0 seconds
ReiserFS: hde3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 160k freed
Adding 1004052k swap on /dev/hde2. Priority:-1 extents:1
ReiserFS: hde3: Removing [5456 746652 0x0 SD]..done
ReiserFS: hde3: Removing [5456 746649 0x0 SD]..done
ReiserFS: hde3: There were 2 uncompleted unlinks/truncates. Completed
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xe0000000
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 0147b:1c00 bound to 0000:00:04.0
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
[fglrx] module loaded - fglrx 3.9.0 [May 11 2004] on minor 0
|
And some misc. info: Gentoo 2004.2 w. 2.6.7-r11 kernel, ATI Radeon 9800 gfx, nForce2 mobo.
Hope someone can get this annoying problem fixed
tia!
|