I have an 86duino which is an x86 single board computer based on a Vortex86EX.
I am trying to boot a pre-packaged image based on tiny core Linux on it
but I have having a problem.
The image is actually a freedos image that uses loadlin
I downloaded the image from here:
https://onedrive.live.com/?cid=65e96...G26g-mtx_wQUgs
Here is the full output over serial:
Code:
Initializing HighMem for node 0 (00000000:00000000)
Memory: 117084k/130944k available (3871k kernel code, 13404k reserved, 1312k data, 496k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff14000 - 0xfffff000 ( 940 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xc87e0000 - 0xff7fe000 ( 880 MB)
lowmem : 0xc0000000 - 0xc7fe0000 ( 127 MB)
.init : 0xc0610000 - 0xc068c000 ( 496 kB)
.data : 0xc04c7c19 - 0xc060ffc0 (1312 kB)
.text : 0xc0100000 - 0xc04c7c19 (3871 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
NR_IRQS:2304 nr_irqs:256 16
Console: colour dummy device 80x25
console [ttyS0] enabled
tsc: Fast TSC calibration using PIT
tsc: Detected 300.003 MHz processor
Calibrating delay loop (skipped), value calculated using timer frequency.. 600.00 BogoMIPS (lpj=1000010)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
tlb_flushall_shift: -1
Freeing SMP alternatives: 12k freed
smpboot: weird, boot CPU (#0) not listed by the BIOS
smpboot: SMP motherboard not detected
smpboot: Local APIC not detected. Using dummy APIC emulation.
smpboot: SMP disabled
Performance Events:
Brought up 1 CPUs
smpboot: Total of 1 processors activated (600.00 BogoMIPS)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfda15, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Interpreter disabled.
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
PCI: Probing PCI hardware
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:07.0: default IRQ router [17f3:6011]
Switching to clocksource pit
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f86e0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xd96a, dseg 0xf0000
PnPBIOS: dev_node_info: function not supported on this system
PnPBIOS: Unable to get node info. Aborting.
pci 0000:00:01.0: PCI bridge to [bus 01]
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 5956k freed
platform rtc_cmos: registered platform RTC device (no PNP device found)
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
fuse init (API version 7.20)
msgmni has been set to 240
NET: Registered protocol family 38
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
isapnp: Scanning for PnP cards...
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
Non-volatile memory driver v1.3
Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using getrawmonotonic().
brd: module loaded
mtip32xx Version 1.2.6os3
Error creating debugfs parent
VMware PVSCSI driver - version 1.0.2.0-k
scsi0 : pata_rdc
scsi1 : pata_rdc
ata1: PATA max UDMA/100 cmd 0x1c30 ctl 0x1c40 bmdma 0x1c20 irq 11
ata2: PATA max UDMA/100 cmd 0x1c38 ctl 0x1c44 bmdma 0x1c28 irq 11
scsi2 : pata_legacy
ata3: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
isapnp: No Plug & Play device found
ata1.00: ATA-6: SA16G D0 RDC SD-IDE HOST CONTROLLER, 01000000, max UDMA/133
ata1.00: 30679040 sectors, multi 1: LBA
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA SA16G D0 RDC SD 0100 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 30679040 512-byte logical blocks: (15.7 GB/14.6 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
scsi3 : pata_legacy
ata4: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:0a.1: EHCI Host Controller
ehci-pci 0000:00:0a.1: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:0a.1: irq 10, io mem 0xfbff5500
ehci-pci 0000:00:0a.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0a.0: OHCI Host Controller
ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 2
genirq: Flags mismatch irq 14. 00000080 (ohci_hcd:usb2) vs. 00000000 (platform)
ohci_hcd 0000:00:0a.0: request interrupt 14 failed
ohci_hcd 0000:00:0a.0: USB bus 2 deregistered
ohci_hcd 0000:00:0a.0: init 0000:00:0a.0 fail, -16
ohci_hcd: probe of 0000:00:0a.0 failed with error -16
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums_eneub6250
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
i8042: PNP: No PS/2 controller found. Probing ports directly.
Switching to clocksource tsc
serio: i8042 KBD port at 0x60,0x64 irq 1
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver appletouch
usbcore: registered new interface driver bcm5974
usbcore: registered new interface driver synaptics_usb
rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 114 bytes nvram
softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
ledtrig-cpu: registered to indicate activity on CPUs
EFI Variables Facility v0.08 2004-May-17
Driver for HIFN 795x crypto accelerator chip has been successfully registered.
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
zram: num_devices not specified. Using default: 1
zram: Creating 1 devices ...
Netfilter messages via NETLINK v0.30.
nfnl_acct: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
IPv4 over IPSec tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
Using IPI No-Shortcut mode
registered taskstats version 1
rtc_cmos rtc_cmos: setting system clock to 2015-01-13 20:13:55 UTC (1421180035)
Freeing unused kernel memory: 496k freed
Write protecting the kernel text: 3872k
Write protecting the kernel read-only data: 980k
Booting Core 5.2
Running Linux Kernel 3.8.13-tinycore.
Checking boot options... Done.
Starting udev daemon for hotplug support... Done.
loop: module loaded
r6040: RDC R6040 NAPI net driver,version 0.28 (07Oct2011)
libphy: r6040_eth_mii: probed
Adding 26096k swap on /dev/zram0. Priority:-1 extents:1 across:26096k SS
Scanning hard disk partitions to create locksource tsc unstable (delta = 166649313 ns)
[1;33m/etc/fstabSwitching to clocksource pit
Setting Language to C Done.
input: PC Speaker as /devices/platform/pcspkr/input/input0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
r6040 0000:00:08.0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0000:00:08.0-0:01)
Possible swap partition(s) enabled.
Loading extensions... Done.
Setting keymap to us Done.
Setting hostname to box Done.
þHZ úÂ`
ÌC GíþÜþÚ
The problem is that at the end it says "Setting hostname to box Done."
then prints some garbage and hangs.
