Hi RedShirt,

Mesa is back again. Here is my dmesg:


display: :0.0 screen: 0
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.2.1)

bgorjup@linux:~> dmesg
Bootdata ok (command line is root=/dev/hda3 vga=0x31a selinux=0 resume=/dev/hda2 splash=silent)
Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
BIOS-e820: 000000001ffc0000 - 000000001ffd0000 (ACPI data)
BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f9cb0
ACPI: RSDT (v001 A M I OEMRSDT 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0000
ACPI: FADT (v002 A M I OEMFACP 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0200
ACPI: MADT (v001 A M I OEMAPIC 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0390
ACPI: OEMB (v001 A M I OEMBIOS 0x07000501 MSFT 0x00000097) @ 0x000000001ffd0040
ACPI: DSDT (v001 A0055 A0055003 0x00000003 INTL 0x02002026) @ 0x0000000000000000
On node 0 totalpages: 130911
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 126912 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
Checking aperture...
CPU 0: aperture @ 2e0000000 size 256 MB
Aperture from northbridge cpu 0 beyond 4GB. Ignoring.
AGP bridge at 00:00:00
Aperture from AGP @ e0000000 size 4096 MB (APSIZE 0)
Aperture from AGP bridge too small (0 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Built 1 zonelists
Kernel command line: root=/dev/hda3 vga=0x31a selinux=0 resume=/dev/hda2 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 1980.134 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 442108k/524032k available (2290k kernel code, 80792k reserved, 825k data, 176k init)
Calibrating delay using timer specific routine.. 3964.42 BogoMIPS (lpj=7928857)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 2800+ stepping 00
checking if image is initramfs... it is
ACPI: Looking for DSDT in initrd... not found!
not found!
Using local APIC timer interrupts.
Detected 13.750 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *7
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
agpgart: Detected AGP bridge 0
agpgart: Aperture conflicts with PCI mapping.
agpgart: Aperture from AGP @ e0000000 size 4096 MB
agpgart: Aperture too small (0 MB)
agpgart: No usable aperture found.
agpgart: Consider rebooting with iommu=memaper=2 to get a good aperture.
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:0b.0
IO window: 9000-9fff
MEM window: ff300000-ff3fffff
PREFETCH window: 9eb00000-deafffff
PCI: Bridge: 0000:00:0e.0
IO window: a000-bfff
MEM window: ff400000-ff5fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0e.0 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1131690232.660:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 10240k, total 262144k
vesafb: mode is 1280x1024x16, linelength=2560, pages=101
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 112645 bytes,<6>...found (1280x1024, 17839 bytes, v3).
Console: switching to colour frame buffer device 158x59
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 8192 (order: 4, 65536 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
NET: Registered protocol family 1
ACPI wakeup devices:
PS2K PS2M UAR1 UAR2 USB0 MAC USB1 USB2 P0P1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
hda: WDC WD800JB-00ETA0, ATA DISK drive
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
hdb: MAXTOR 6L040J2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: max request size: 128KiB
hdb: 78177792 sectors (40027 MB) w/1820KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3520AW, ATAPI CD/DVD-ROM drive
hdd: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
libata version 1.12 loaded.
sata_nv version 0.6
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 22 (level, low) -> IRQ 177
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xC800 irq 177
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xC808 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
sata_sil version 0.9
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKC] -> GSI 19 (level, low) -> IRQ 185
Losing some ticks... checking if CPU frequency changed.
ata3: SATA max UDMA/100 cmd 0xFFFFC2000001CC80 ctl 0xFFFFC2000001CC8A bmdma 0xFFFFC2000001CC00 irq 185
ata4: SATA max UDMA/100 cmd 0xFFFFC2000001CCC0 ctl 0xFFFFC2000001CCCA bmdma 0xFFFFC2000001CC08 irq 185
ata5: SATA max UDMA/100 cmd 0xFFFFC2000001CE80 ctl 0xFFFFC2000001CE8A bmdma 0xFFFFC2000001CE00 irq 185
ata6: SATA max UDMA/100 cmd 0xFFFFC2000001CEC0 ctl 0xFFFFC2000001CECA bmdma 0xFFFFC2000001CE08 irq 185
ata3: no device found (phy stat 00000000)
scsi2 : sata_sil
ata4: no device found (phy stat 00000000)
scsi3 : sata_sil
ata5: no device found (phy stat 00000000)
scsi4 : sata_sil
ata6: no device found (phy stat 00000000)
scsi5 : sata_sil
ACPI: CPU0 (power states: C1[C1])
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 1012084k swap on /dev/hda2. Priority:-1 extents:1
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff803cf000(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI-0212: *** Warning: Device is not power manageable
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 304 bytes per conntrack
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 193, io mem 0xff6fd000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 20 (level, low) -> IRQ 201
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 201, io mem 0xff6fe000
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LKLN] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:05.0 to 64
usb 1-1: new full speed USB device using ohci_hcd and address 2
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 193, io mem 0xff6ffc00
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:05.0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 20 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:06.0 to 64
usb 3-1: new high speed USB device using ehci_hcd and address 2
Linux video capture interface: v1.00
ohci_hcd 0000:00:02.1: wakeup
intel8x0_measure_ac97_clock: measured 73855 usecs
intel8x0: clocking to 47162
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 209
saa7134[0]: found at 0000:02:07.0, rev: 1, irq: 209, latency: 64, mmio: 0xff5ffc00
saa7134[0]: subsystem: 153b:1158, board: Terratec Cinergy 600 TV MK3 [card=48,autodetected]
saa7134[0]: board init: gpio is 50000
saa7134[0]: registered input device for IR
usb 2-2: new full speed USB device using ohci_hcd and address 2
saa7134[0]: i2c eeprom 00: 3b 15 58 11 ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
: chip found @ 0xc0 (saa7134[0])
: All bytes are equal. It is not a TEA5767
tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
Floppy drive(s): fd0 is 1.44M
ieee1394: Initialized config rom entry `ip1394'
FDC 0 is a post-1991 82077
tda9885/6/7: chip found @ 0x86
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 209
PCI: Via IRQ fixup for 0000:02:0b.0, from 10 to 1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209] MMIO=[ff5ff000-ff5ff7ff] Max Packet=[2048]
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800008984f4]
it87: Found IT8712F chip at 0xd00, revision 7
bootsplash: status on console 0 changed to on
NET: Registered protocol family 17
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
IA-32 Microcode Update Driver v1.14 unregistered
bootsplash: status on console 0 changed to on
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
ACPI-0071: *** Warning: Invalid 'package' argument
ACPI-0285: *** Warning: Invalid _PSS data
powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x2 (1500 mV)
cpu_init done, current fid 0xa, vid 0x2
bootsplash: status on console 0 changed to on
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
eth0: no IPv6 routers present
fglrx: module not supported by Novell, setting U taint flag.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 366 MBytes.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 17 (level, low) -> IRQ 217
[fglrx] module loaded - fglrx 8.18.8 [Oct 25 2005] on minor 0
[fglrx:firegl_unlock] *ERROR* Process 5658 using kernel context 0

my lsmod:

linux:/home/bgorjup # lsmod
Module Size Used by
appletalk 42064 2
ax25 72232 2
ipx 31568 2
fglrx 286748 0
hfsplus 85640 0
subfs 9600 1
ipt_pkttype 2176 1
ipt_LOG 8064 7
ipt_limit 2944 7
cpufreq_ondemand 8108 1
cpufreq_userspace 5828 0
cpufreq_powersave 2304 0
powernow_k8 11792 0
freq_table 5512 1 powernow_k8
snd_pcm_oss 70432 0
snd_mixer_oss 22144 1 snd_pcm_oss
snd_seq 68824 0
snd_seq_device 11024 1 snd_seq
button 8736 0
battery 12296 0
ac 6664 0
edd 12448 0
af_packet 25356 2
it87 27040 0
eeprom 9232 0
i2c_sensor 3968 2 it87,eeprom
i2c_isa 2944 0
usblp 15488 0
ip6t_REJECT 6528 3
tda9887 15376 0
ipt_REJECT 6656 3
ohci1394 36684 0
ieee1394 118648 1 ohci1394
floppy 73792 0
tuner 41384 0
ipt_state 2432 12
saa7134 130516 0
video_buf 27012 1 saa7134
crc_ccitt 2560 0
isdn 154592 0
slhc 8192 1 isdn
iptable_mangle 3584 0
v4l2_common 8192 1 saa7134
v4l1_compat 13956 1 saa7134
ir_common 9860 1 saa7134
videodev 12544 1 saa7134
iptable_nat 28120 0
iptable_filter 3712 1
snd_intel8x0 40000 1
snd_ac97_codec 117060 1 snd_intel8x0
snd_ac97_bus 3328 1 snd_ac97_codec
snd_pcm 117260 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 29320 2 snd_seq,snd_pcm
snd 77600 10 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 11808 2 saa7134,snd
snd_page_alloc 13200 2 snd_intel8x0,snd_pcm
generic 5892 0 [permanent]
ip6table_mangle 2944 0
shpchp 101032 0
pci_hotplug 31720 1 shpchp
ehci_hcd 36744 0
forcedeth 22144 0
i2c_nforce2 8576 0
i2c_core 25752 8 it87,eeprom,i2c_sensor,i2c_isa,tda9887,tuner,saa7134,i2c_nforce2
ip_conntrack 51572 2 ipt_state,iptable_nat
ohci_hcd 22916 0
usbcore 140724 4 usblp,ehci_hcd,ohci_hcd
ip_tables 22528 8 ipt_pkttype,ipt_LOG,ipt_limit,ipt_REJECT,ipt_state,iptable_mangle,iptable_nat,iptable_filter
ip6table_filter 3456 1
ip6_tables 21120 3 ip6t_REJECT,ip6table_mangle,ip6table_filter
ipv6 289024 17 ip6t_REJECT
parport_pc 44912 0
lp 14336 0
parport 43532 2 parport_pc,lp
nls_iso8859_1 5760 2
nls_cp437 7424 2
vfat 15872 2
fat 58032 1 vfat
dm_mod 65648 0
reiserfs 267120 1
fan 6152 0
thermal 17932 0
processor 28368 2 powernow_k8,thermal
sata_sil 11780 0
ide_cd 45984 0
cdrom 40888 1 ide_cd
sata_nv 11396 0
libata 57608 2 sata_sil,sata_nv
amd74xx 16048 0 [permanent]
sd_mod 20760 0
scsi_mod 161976 2 libata,sd_mod
ide_disk 19584 6
ide_core 158616 4 generic,ide_cd,amd74xx,ide_disk
linux:/home/bgorjup #


and

linux:/home/bgorjup # lspci | grep AGP
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
linux:/home/bgorjup #


Funny thing, I have now restarted and fglrx is back again ???

This is too weird... The dmesg you posted shows it never even thought about loading anything but Mesa, has no AGPGART at all loading...
That has me very concerned, it is forcing memory into video use, as it doesn't fin any from the video card listed in the bios!? I think I would recommend popping into the bios now, and changing some settings, you need to make the aperature 256Mb. Check to make sure everything else looks good too, because maybe something squirrely is going on there.

Something really funny is going on.
"00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)" is set properly as your AGPGART module but linux doesn't want to load it...

I wonder....since you can uninstall all nvidia driver with a command, I am betting there is a way to uninstall all the mesa drivers. I just don't know how. That could help.

I really don't know though, you are walking in some weird territory.

I have the exact same problem, and I'm looking for a solution, but I have a work around. I boot into Windows first.

For some reason from a cold boot (power off, boot straight into linux) it can't get the AGP apeture size. Booting into windows and then rebooting into linux lets it see that AGP Apeture and voila, fglrx works.

You have alot more detail in your dmesg than I do for some reason, but this is what I get from a cold boot:

agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.

and from a reboot from WIndows:

agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 512M @ 0xc0000000

and then when trying to start X from a cold boot:

fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 804 MBytes.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
[fglrx] module loaded - fglrx 8.18.6 [Oct 11 2005] on minor 0
[fglrx:firegl_unlock] *ERROR* Process 5472 using kernel context 0

and from a reboot from windows:

fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 804 MBytes.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
[fglrx] module loaded - fglrx 8.18.6 [Oct 11 2005] on minor 0
[fglrx] Kernel AGP support doesn't provide agplock functionality.
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 520876032
[fglrx] max AGP = 520876032
[fglrx] free LFB = 122679296
[fglrx] max LFB = 122679296
[fglrx] free Inv = 134217728
[fglrx] max Inv = 134217728
[fglrx] total Inv = 134217728
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 131072

I'm running Slackware 10.2 Kernel 2.6.13 on an Asus K8N-E Deluxe which uses the nForce3-250 chipset, with an ATI Radeon X800 XL.

I'm also running bios 1010.003 (beta) and I see that 1011 and 1012..02 are out, so I might give them a try.

Finally, I also tried the fglrx internal agpgart, but I didn't save the log, but it said something about an unsupported chipset. (Only tried cold, not a reboot from windows, I think I'll do that now).

HTH.

Well, right now I have removed every piece of fglrx from the system (I used a synaptic). Then I installed ATI Installer-I followed the instructions as written here:

http://www.susewiki.org/index.php?ti..._Installation. I skipped 8 and went directly to 9. Now my dmesg is:
[fglrx] module loaded - fglrx 8.18.8 [Oct 25 2005] on minor 0
[fglrx] module unloaded - fglrx 8.18.8 [Oct 25 2005] on minor 0
fglrx: module not supported by Novell, setting U taint flag.
[fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 17 (level, low) -> IRQ
217
[fglrx] module loaded - fglrx 8.18.8 [Oct 25 2005] on minor 0
[fglrx] Kernel AGP support doesn't provide agplock functionality.
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 256126976
[fglrx] max AGP = 256126976
[fglrx] free LFB = 116387840
[fglrx] max LFB = 116387840
[fglrx] free Inv = 134217728
[fglrx] max Inv = 134217728
[fglrx] total Inv = 134217728
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 65536
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 256126976
[fglrx] max AGP = 256126976
[fglrx] free LFB = 116387840
[fglrx] max LFB = 116387840
[fglrx] free Inv = 134217728
[fglrx] max Inv = 134217728
[fglrx] total Inv = 134217728
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 65536
NET: Registered protocol family 4
ax25: module not supported by Novell, setting U taint flag.
NET: Registered protocol family 3


bgorjup@linux:~> lsmod
Module Size Used by
appletalk 42064 2
ax25 72232 2
ipx 31568 2
fglrx 286748 7
joydev 12288 0
hfsplus 85640 0

linux:/home/bgorjup # lspci | grep AGP
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
linux:/home/bgorjup #
I hope it will not change to Mesa drivers tomorrow

The link you posted goes to a blank page...
"SUSE 10: ATI Driver Installation.
From SUSE Wiki

(There is currently no text in this page) "

So, don't know how useful the directions you followed are, but my guess is they were wrong and thus stripped down. Or possibly outdated or something, I don't know for sure.

Good luck with those though, perhaps it will stick. If not, I am wondering if perhaps a kernel upgrade might be in order, or a bios update, or both...

http://www.susewiki.org/index.php?ti...r_Installation

I checked and rechecked and it is ok.

SUSE 10: ATI Driver Installation
[edit]
Introduction
I am running SUSE 10.0 (GM) in 32bit mode and ATI 9800XT AGP Card.
Make sure that you have installed: 1. kernel-source 2. gcc 3. make (all from Yast)
“Since ATI driver release 8.16.20 the ATI installer needs to be used to create SUSE RPMs. Download the ATI installer from the ATI website.
http://www.ati.com –> Drivers & Software –> Linux”


[edit]
Installation
1. Download the ATI Driver Installer (~56MB) from ATI’s site
2. Switch to root:
~> su


3.
# sh ./ati-driver-installer-8.xx.xx-i386.run --get-supported

(this will show the supported OS, which in my case was SuSE/SUSE100-IA32)

4.
# sh ./ati-driver-installer-8.xx.xx-i386.run --buildpkg SuSE/SUSE100-IA32

(this will create rpm installer for ATI drivers for your distro)

5. Now switch to init 3
# init 3

6. Log in as root and then install driver:
7.
# rpm -Uhv fglrx_6_8_0_SUSE-8.xx.xx.1.i386.rpm


8. If you are running 64bit environment, then follow this, or skip to step 9
a. Download from SUSE FTP file called: fglrx64_6_8_0-8.xx.xx-1.x86_64.diff
Update: Seems like that from version 8.18.6-x86_64 +, the patch command is NOT required, so skip this one, as this was needed with previous versions.
b.
# cp fglrx64_6_8_0-8.xx.xx-1.x86_64.diff /usr/src/kernel-modules/fglrx


c.
# cd /usr/src/kernel-modules/fglrx


d.
# patch -p0 < fglrx64_6_8_0-8.xx.xx-1.x86_64.diff


e. Then start again:
# /usr/X11R6/bin/fglrx-kernel-build.sh


9. Once all this is completed, all that is left is to run sax2 to configure the driver:
# sax2 -r -m 0=fglrx -b /usr/share/doc/packages/fglrx/sax2-profile


10. Accept the default changes or if you want otchange somthing else go and customize.
11. Now back to Desktop Environment by running the following command:
# init 5


Remember, the 3D icon in the middle of the screen is not always shown as enabled. That is OK. Once all the above has been completed, we will run few tests to make sure that 3D is being enabled.
[edit]
Testing
Once in KDE/Gnome, open your terminal and run the following commands as “user”
~> fglrxinfo

(the output should state ATI and not MESA)
~> glxgears

(a simple 3D OpenGL test, in my case I am getting ~4800fps and before installing drivers it was ~180fps)

If for some reason you are not getting ATI as output with “fglrxinfo” command, simply repeat the step 9 once more.

Hope that will be of some assistance.

E@zyVG
Categories: Howto

I have noticed one funny thing connected to the "disappearance" and changing ATI and Mesa drivers.
Gkrellm which has been running on my desktop shows also temperatures ( motherboard, CPU, HDD), voltages (+3,5 ; 12,0 and 5,0V) and fans. So what is funny? When there is fglrx ATI driver running, the above mentioned sensors reading is gone and when Mesa drivers are running they show again.

Hi,

Well there is no change in behavior of my fglrx and Meas drivers changing. Every morning I start my computer and check whether it is running fglrx or Mesa it is Mesa. So I have to init 3 and write again " sax2 -r -m ......." go to init 5 and reboot . Again I am in fglrx "mode" for as long as "next morning".

I really want to get to the "bottom" of the problem. Any suggestions???

Here's something really weird I just noticed with the latest SUSE drivers (8.19.10).

If I run as user
fglrxinfo
I get
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: MOBILITY RADEON 9600 Generic
OpenGL version string: 1.3.5461 (X4.3.0-8.19.10)

If I run the same as root, I get
display: :0.0 screen: 0
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.2.1)

I don't know if this is a bug or what. 3D (as user) is definitely working, but I'm confused. BTW I'm using SUSE 9.3 - not 10.0.

Well, I was just going to recommend trying the new drivers... the 8.19.10.

After a boot when it loaded the ATIs, try checking the xorg.conf, making sure it is the ATI generated one, then back it up as xorg.conf.old. Just to make sure it isn't loading an old one sometimes.
Also, can you check the xorg.0.log when it loads the mesas? Maybe there is something quirky going on there...If that doesn't work, I am thinking we may need to have you set up some kind of script on boot which checks for the right drivers, but man, that is getting into really advanced stuff we shouldnt' need to get into just to have drivers stick.

winesquire - There is a line during fglrx configuration which mentions who is allows to run the drivers and DRI specifically. Make sure you hit "0" here, which is all.

I think that's it. In my DRI section I have a group specified and root is not in that group. D'oh!

Thanks
ws

On your first boot of the morning, post the results of

dmesg | grep agpgart

confirm that fglrx failed to load (running under MESA) then warm reboot (keep power on) and run that line again. If it's the same and you are still under mesa, then run your sax2 command reboot and grep dmesg for agpgart one last time.

My problem seems to be related to agpgart not starting properly on a cold boot and maybe the same thing is happening to you.

._.

Hi,

Now I have another problem. Yesterday I removed fglrx drivers from my system because I want to install the new driver. I do not know what happened but after restarting I cant enter into KDE. To save the time I reinstalled SUSE 10.0. Now, when downloading ATI installer and driver , I run sh ./ati-driver-installer......--get-supported , there is no support for SUSE. And when I run the older version of the installer, there is NO support for SUSE either ????? So I am not able and use ATI Driver Installer any more. Where is the problem now???? I can reinstall SUSE again if there is no other solution.

Don't worry about get supported. They work just fine on SuSE 10.0, I am using them now. Just install the rpm, and do a basic ./ on the driver install script, and then run the fglrx command. Because this is just a basic install, it will be fine on all linux which supports rpm packages. You can follow my guide if you need to, but I think you should just do a straight install, dont' worry about making an rpm to install or anything, it wil appear in the KDM menu just fine.

Hi RedShirt,

I just test my fglrx and they are working well for the moment!!!! I am gonna experment now a little bit. it is a new fglrx driver. We ll see the results soon !!!

cheers

This are my glxgears now. They are the same as last time but it works.

bgorjup@Bogomir:~> fglrxinfo
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: RADEON 9600 Generic
OpenGL version string: 1.3.5461 (X4.3.0-8.19.10)

bgorjup@Bogomir:~> glxgears
8862 frames in 5.0 seconds = 1772.400 FPS
9175 frames in 5.0 seconds = 1835.000 FPS
10123 frames in 5.0 seconds = 2024.600 FPS
10123 frames in 5.0 seconds = 2024.600 FPS
10111 frames in 5.0 seconds = 2022.200 FPS

my dmesg:

Bootdata ok (command line is root=/dev/hda3 vga=0x31a selinux=0 resume=/dev/hda2 splash=silent)
Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
BIOS-e820: 000000001ffc0000 - 000000001ffd0000 (ACPI data)
BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000f9cb0
ACPI: XSDT (v001 A M I OEMXSDT 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0100
ACPI: FADT (v003 A M I OEMFACP 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0290
ACPI: MADT (v001 A M I OEMAPIC 0x07000501 MSFT 0x00000097) @ 0x000000001ffc0390
ACPI: OEMB (v001 A M I OEMBIOS 0x07000501 MSFT 0x00000097) @ 0x000000001ffd0040
ACPI: DSDT (v001 A0055 A0055003 0x00000003 INTL 0x02002026) @ 0x0000000000000000
On node 0 totalpages: 130911
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 126912 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
Checking aperture...
CPU 0: aperture @ f0000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/hda3 vga=0x31a selinux=0 resume=/dev/hda2 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 1980.134 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 507900k/524032k available (2290k kernel code, 15256k reserved, 825k data, 176k init)
Calibrating delay using timer specific routine.. 3964.42 BogoMIPS (lpj=7928855)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 2800+ stepping 00
checking if image is initramfs... it is
ACPI: Looking for DSDT in initrd... not found!
not found!
Using local APIC timer interrupts.
Detected 13.750 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *7
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:0b.0
IO window: 9000-9fff
MEM window: ff300000-ff3fffff
PREFETCH window: aeb00000-eeafffff
PCI: Bridge: 0000:00:0e.0
IO window: a000-bfff
MEM window: ff400000-ff5fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0e.0 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1132161660.676:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000100000, using 10240k, total 262144k
vesafb: mode is 1280x1024x16, linelength=2560, pages=101
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 112645 bytes,<6>...found (1280x1024, 17839 bytes, v3).
Console: switching to colour frame buffer device 158x59
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 8192 (order: 4, 65536 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
NET: Registered protocol family 1
ACPI wakeup devices:
PS2K PS2M UAR1 UAR2 USB0 MAC USB1 USB2 P0P1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
hda: WDC WD800JB-00ETA0, ATA DISK drive
hdb: MAXTOR 6L040J2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: max request size: 128KiB
hdb: 78177792 sectors (40027 MB) w/1820KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3520AW, ATAPI CD/DVD-ROM drive
hdd: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
libata version 1.12 loaded.
sata_nv version 0.6
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:0a.0 to 64
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xC800 irq 177
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xC808 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
sata_sil version 0.9
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKC] -> GSI 19 (level, low) -> IRQ 185
Losing some ticks... checking if CPU frequency changed.
ata3: SATA max UDMA/100 cmd 0xFFFFC20000020C80 ctl 0xFFFFC20000020C8A bmdma 0xFFFFC20000020C00 irq 185
ata4: SATA max UDMA/100 cmd 0xFFFFC20000020CC0 ctl 0xFFFFC20000020CCA bmdma 0xFFFFC20000020C08 irq 185
ata5: SATA max UDMA/100 cmd 0xFFFFC20000020E80 ctl 0xFFFFC20000020E8A bmdma 0xFFFFC20000020E00 irq 185
ata6: SATA max UDMA/100 cmd 0xFFFFC20000020EC0 ctl 0xFFFFC20000020ECA bmdma 0xFFFFC20000020E08 irq 185
ata3: no device found (phy stat 00000000)
scsi2 : sata_sil
ata4: no device found (phy stat 00000000)
scsi3 : sata_sil
ata5: no device found (phy stat 00000000)
scsi4 : sata_sil
ata6: no device found (phy stat 00000000)
scsi5 : sata_sil
ACPI: CPU0 (power states: C1[C1])
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 1012084k swap on /dev/hda2. Priority:-1 extents:1
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff803cf000(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35.
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LKLN] -> GSI 21 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:05.0 to 64
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 20 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 201, io mem 0xff6fd000
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 177, io mem 0xff6fe000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 193, io mem 0xff6ffc00
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ip_tables: (C) 2000-2002 Netfilter core team
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:05.0
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 20 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:06.0 to 64
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 304 bytes per conntrack
usb 3-1: new high speed USB device using ehci_hcd and address 2
intel8x0_measure_ac97_clock: measured 54754 usecs
intel8x0: clocking to 46932
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ohci_hcd 0000:00:02.1: wakeup
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 209
saa7134[0]: found at 0000:02:07.0, rev: 1, irq: 209, latency: 64, mmio: 0xff5ffc00
saa7134[0]: subsystem: 153b:1158, board: Terratec Cinergy 600 TV MK3 [card=48,autodetected]
saa7134[0]: board init: gpio is 50000
saa7134[0]: registered input device for IR
saa7134[0]: i2c eeprom 00: 3b 15 58 11 ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
ieee1394: Initialized config rom entry `ip1394'
: chip found @ 0xc0 (saa7134[0])
: All bytes are equal. It is not a TEA5767
tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
usb 2-2: new full speed USB device using ohci_hcd and address 2
tda9885/6/7: chip found @ 0x86
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 209
PCI: Via IRQ fixup for 0000:02:0b.0, from 10 to 1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209] MMIO=[ff5ff000-ff5ff7ff] Max Packet=[2048]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800008984f4]
it87: Found IT8712F chip at 0xd00, revision 7
NET: Registered protocol family 17
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
ACPI-0071: *** Warning: Invalid 'package' argument
ACPI-0285: *** Warning: Invalid _PSS data
powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x2 (1500 mV)
cpu_init done, current fid 0xa, vid 0x2
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.100 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.100 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.100 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdd: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xb0
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.100 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
lp: driver loaded but no devices found
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
fglrx: module not supported by Novell, setting U taint flag.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 17 (level, low) -> IRQ 217
[fglrx] module loaded - fglrx 8.19.10 [Nov 9 2005] on minor 0
[fglrx] module unloaded - fglrx 8.19.10 [Nov 9 2005] on minor 0
SFW2-INext-DROP-DEFLT-INV IN=eth0 OUT= MAC=00:e0:18:99:88:77:00:30:4f:39:b8:ba:08:00 SRC=193.189.160.47 DST=192.168.0.100 LEN=1392 TOS=0x00 PREC=0x00 TTL=60 ID=30643 DF PROTO=TCP SPT=110 DPT=11255 WINDOW=25460 RES=0x00 ACK URGP=0 OPT (0101080ABB9B52F20043EA66)
mtrr: no MTRR for d0000000,8000000 found
Unable to handle kernel paging request at ffffffaa803a9a68 RIP:
<ffffffff80135a37>{do_exit+791}
PGD 103027 PUD 0
Oops: 0000 [1]
CPU 0
Modules linked in: parport_pc lp parport bluetooth nls_utf8 hfsplus subfs ipt_pkttype ipt_LOG ipt_limit cpufreq_ondemand cpufreq_userspace cpufreq_powersave powernow_k8 freq_table snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device button battery ac edd af_packet it87 eeprom i2c_sensor i2c_isa ip6t_REJECT ipt_REJECT ipt_state usblp iptable_mangle floppy tda9887 iptable_nat tuner ohci1394 ieee1394 iptable_filter crc_ccitt isdn slhc saa7134 video_buf v4l2_common v4l1_compat ir_common videodev ip6table_mangle ip_conntrack ip_tables generic shpchp pci_hotplug snd_intel8x0 snd_ac97_codec snd_ac97_bus snd_pcm snd_timer snd soundcore snd_page_alloc ehci_hcd i2c_nforce2 i2c_core ohci_hcd usbcore forcedeth ip6table_filter ip6_tables ipv6 nls_iso8859_1 nls_cp437 vfat fat dm_mod reiserfs fan thermal processor sata_sil ide_cd cdrom sata_nv libata amd74xx sd_mod scsi_mod ide_disk ide_core
Pid: 6398, comm: konqueror Tainted: P U 2.6.13-15-default
RIP: 0010:[<ffffffff80135a37>] <ffffffff80135a37>{do_exit+791}
RSP: 0018:ffff810007243d98 EFLAGS: 00010246
RAX: ffffffaa803a9a20 RBX: ffff81001fa60c00 RCX: 0000000000000037
RDX: 000000000000004e RSI: 0000000000000000 RDI: ffff81001ffb9400
RBP: 0000000000000001 R08: 0000000000000003 R09: 00000000000000c8
R10: 0000000000000000 R11: ffffffff880b88b0 R12: ffff810018e676f0
R13: 0000000000000001 R14: 0000000000000000 R15: ffff810018e67cc8
FS: 00002aaaae4d8dc0(0000) GS:ffffffff8049b800(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffaa803a9a68 CR3: 000000001fd25000 CR4: 00000000000006e0
Process konqueror (pid: 6398, threadinfo ffff810007242000, task ffff810018e676f0)
Stack: ffff81001ef24998 ffff810007243ef8 ffff810007243e78 ffff810018e676f0
ffff810018e67cc8 0000000000000001 ffff810007243e78 ffff810018e67cc8
0000000000b1f320 0000000000000000
Call Trace:<ffffffff80136331>{do_group_exit+177} <ffffffff8013fe07>{get_signal_to_deliver+1255}
<ffffffff8010e06d>{do_signal+157} <ffffffff8018a30e>{open_namei+766}
<ffffffff8017a2b8>{get_empty_filp+120} <ffffffff8017884e>{dentry_open+286}
<ffffffff80178994>{filp_open+68} <ffffffff8010e9a3>{sysret_signal+28}
<ffffffff8010ec8b>{ptregscall_common+103}

Code: 48 8b 40 48 48 85 c0 74 17 ff 88 80 01 00 00 83 38 02 75 0c
RIP <ffffffff80135a37>{do_exit+791} RSP <ffff810007243d98>
CR2: ffffffaa803a9a68
<1>Fixing recursive fault but reboot is needed!
fglrx: module not supported by Novell, setting U taint flag.
[fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 17 (level, low) -> IRQ 217
[fglrx] module loaded - fglrx 8.19.10 [Nov 9 2005] on minor 0
[fglrx] Kernel AGP support doesn't provide agplock functionality.
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 121909248
[fglrx] max AGP = 121909248
[fglrx] free LFB = 116387840
[fglrx] max LFB = 116387840
[fglrx] free Inv = 134217728
[fglrx] max Inv = 134217728
[fglrx] total Inv = 134217728
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 32768
bgorjup@Bogomir:~>