LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware > Slackware - Installation
User Name
Password
Slackware - Installation This forum is for the discussion of installation issues with Slackware.

Notices



Reply
 
Search this Thread
Old 06-13-2013, 10:25 AM   #1
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Rep: Reputation: 2
Fresh install of 14.0 64-bit to new machine: frozen gui at startx


1. chose kde
2. entered startx from command line
3. got blue screen, then blacked out, then after 2 seconds, blue screen again,
with first icon (a disk I think), a cursor frozen mid-screen
4. no keyboard
5. no mouse action

here is the output of:
lspci -vnn:
Code:
lebec@DarkDuck ~ $ lspci -vnn
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09)
	Subsystem: Giga-byte Technology Device [1458:5000]
	Flags: bus master, fast devsel, latency 0
	Capabilities: <access denied>

00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller [8086:0152] (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Giga-byte Technology Device [1458:d000]
	Flags: bus master, fast devsel, latency 0, IRQ 44
	Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
	Memory at e0000000 (64-bit, prefetchable) [size=256M]
	I/O ports at f000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: i915
	Kernel modules: i915

00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
	Subsystem: Giga-byte Technology Device [1458:5007]
	Flags: bus master, medium devsel, latency 0, IRQ 42
	Memory at f7c00000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd

00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
	Subsystem: Giga-byte Technology Device [1458:1c3a]
	Flags: bus master, fast devsel, latency 0, IRQ 45
	Memory at f7c19000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>
	Kernel driver in use: mei
	Kernel modules: mei

00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Giga-byte Technology Device [1458:5006]
	Flags: bus master, medium devsel, latency 0, IRQ 16
	Memory at f7c17000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
	Subsystem: Giga-byte Technology Device [1458:a002]
	Flags: bus master, fast devsel, latency 0, IRQ 46
	Memory at f7c10000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1c.4 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 [8086:1e18] (rev c4) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Giga-byte Technology Device [1458:5006]
	Flags: bus master, medium devsel, latency 0, IRQ 23
	Memory at f7c16000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a4) (prog-if 01 [Subtractive decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation B75 Express Chipset LPC Controller [8086:1e49] (rev 04)
	Subsystem: Giga-byte Technology Device [1458:5001]
	Flags: bus master, medium devsel, latency 0
	Capabilities: <access denied>
	Kernel modules: lpc_ich

00:1f.2 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 4-port SATA Controller [IDE mode] [8086:1e00] (rev 04) (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: Giga-byte Technology Device [1458:b005]
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
	I/O ports at f110 [size=8]
	I/O ports at f100 [size=4]
	I/O ports at f0f0 [size=8]
	I/O ports at f0e0 [size=4]
	I/O ports at f0d0 [size=16]
	I/O ports at f0c0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
	Subsystem: Giga-byte Technology Device [1458:5001]
	Flags: medium devsel, IRQ 11
	Memory at f7c15000 (64-bit, non-prefetchable) [size=256]
	I/O ports at f040 [size=32]
	Kernel modules: i2c-i801

00:1f.5 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 2-port SATA Controller [IDE mode] [8086:1e08] (rev 04) (prog-if 85 [Master SecO PriO])
	Subsystem: Giga-byte Technology Device [1458:b002]
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
	I/O ports at f0b0 [size=8]
	I/O ports at f0a0 [size=4]
	I/O ports at f090 [size=8]
	I/O ports at f080 [size=4]
	I/O ports at f070 [size=16]
	I/O ports at f060 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
	Subsystem: Giga-byte Technology GA-EP45-DS5/GA-EG45M-DS2H Motherboard [1458:e000]
	Flags: bus master, fast devsel, latency 0, IRQ 43
	I/O ports at e000 [size=256]
	Memory at f0004000 (64-bit, prefetchable) [size=4K]
	Memory at f0000000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

lebec@DarkDuck ~ $
It is a AOC wide screen, connected to a Thermaltake with 8gig ram, currently running Archbang and Mint on other partitions.

Any suggestions guys/gals?
 
Old 06-13-2013, 11:41 AM   #2
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,520

Rep: Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874
1. Rinse and repeat. I have had occasions that I have had to try starting KDE a few times before it would come up successfully.
2. Try another window manager e.g xfce
3. Check /var/log/Xorg.0.log for errors.
 
1 members found this post helpful.
Old 06-13-2013, 01:13 PM   #3
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
thanks allend; i just noticed you are from my old home "town"

(i love the "argo": "rinse and repeat"... had a chuckle)

: 0 )

So, you are telling me to re-install right? (run through the "cycle" again?)
 
Old 06-13-2013, 06:54 PM   #4
Didier Spaier
Senior Member
 
Registered: Nov 2008
Location: Paris, France
Distribution: Slackware{,64}-{14.1,current} on a Lenovo Thinkpad T61 6457-4XG
Posts: 4,661

Rep: Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236Reputation: 1236
I don't think allend meant that you need to reinstall anything.

If you start at runlevel 3 (console mode), type 'xwmconfig' to chose another DE or WM (than KDE) before running 'startx'.

If you start in runlevel 4, choose another DE or WM clicking the arrow (IIRC).

Last edited by Didier Spaier; 06-21-2013 at 12:52 AM. Reason: Typos corrected
 
1 members found this post helpful.
Old 06-13-2013, 07:12 PM   #5
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,520

Rep: Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874
No, not reinstall, just try starting KDE a few times. KDE does autodetection at startup and stores information in configuration files. This may not always be a smooth process.
If you are still having problems, then try a different window manager, to test whether it is just KDE or a more fundamental problem with X.
If an alternative window manager works, then try starting KDE with compositing disabled. From CHANGES_AND_HINTS.TXT
Code:
Regardless of your chipset (though it seems more common with intel), if KDE
  crashes on startup, try disabling the Composite extension (which will also
  disable all of the fancy desktop effects).  Place the following content in
  a file at /etc/X11/xorg.conf.d/disable-composite.conf:
    Section "Extensions"
      Option "Composite" "Disable"
    EndSection
If an alternative window manager fails, then it may be a problem with X. The output from /var/log/Xorg.0.log can help here.

Aside- This 'Mexican' says to watch out for banana benders!
 
1 members found this post helpful.
Old 06-14-2013, 03:38 AM   #6
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
Quote:
Originally Posted by allend View Post
No, not reinstall, just try starting KDE a few times. KDE does autodetection at startup and stores information in configuration files. This may not always be a smooth process.
If you are still having problems, then try a different window manager, to test whether it is just KDE or a more fundamental problem with X.

If an alternative window manager fails, then it may be a problem with X. The output from /var/log/Xorg.0.log can help here.

Aside- This 'Mexican' says to watch out for banana benders!
I notice you are running "current".
I think I might cut my losses with this bootable version 14 64-bit and
go for a clean install of current.

(when i moved up here to northern rivers i was told by a casual acquaintance to change the plates on my bike so people would stop aiming for me on the road ...
they are strange drivers up here: more conservative somehow and far less tolerant of "bad" behaviour (aka "creative transits") by bikers: ie: lane-splitting, for example, which is charmingly overlooked by melbourne drivers and ruthlessly persecuted by their new south welshperson equivalents)

cheers
 
Old 06-14-2013, 10:13 AM   #7
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
After repeated attempts using various DEnvironments, I gave up and re-installed.
Now, in ALL DE, the gui is fragmented: parts of screen unreadable, terminal output patchy.

I'm going to capture the log report but here is something else which might be diagnostic: when I tried to run install in VirtualBox, I got an error message on startup saying that VM was seeing my machine as 32-bit and that as such it wouldn't be able to run the inserted software in VM (nameley, my 64-bit version of slackware)
 
Old 06-14-2013, 10:37 AM   #8
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
output of /var/log/Xorg.O.log (part 1) ... it was too long to do in 1 go

Quote:
Originally Posted by allend View Post
The output from /var/log/Xorg.0.log can help here.
Requested output:

Code:
[    17.785] 
X.Org X Server 1.12.3
Release Date: 2012-07-09
[    17.785] X Protocol Version 11, Revision 0
[    17.785] Build Operating System: Slackware 14.0 Slackware Linux Project
[    17.785] Current Operating System: Linux darkstar 3.2.29 #2 SMP Mon Sep 17 14:19:22 CDT 2012 x86_64
[    17.785] Kernel command line: BOOT_IMAGE=/boot/vmlinuz root=/dev/sda3
[    17.785] Build Date: 23 August 2012  02:03:27PM
[    17.785]  
[    17.785] Current version of pixman: 0.26.2
[    17.785] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    17.785] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    17.785] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Jun 14 14:17:05 2013
[    17.834] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    17.845] (==) No Layout section.  Using the first Screen section.
[    17.845] (==) No screen section available. Using defaults.
[    17.845] (**) |-->Screen "Default Screen Section" (0)
[    17.845] (**) |   |-->Monitor "<default monitor>"
[    17.845] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[    17.845] (==) Automatically adding devices
[    17.845] (==) Automatically enabling devices
[    17.845] (WW) The directory "/usr/share/fonts/local" does not exist.
[    17.845] 	Entry deleted from font path.
[    17.845] (WW) The directory "/usr/share/fonts/CID" does not exist.
[    17.845] 	Entry deleted from font path.
[    17.871] (==) FontPath set to:
	/usr/share/fonts/TTF,
	/usr/share/fonts/OTF,
	/usr/share/fonts/Type1,
	/usr/share/fonts/misc,
	/usr/share/fonts/75dpi/:unscaled,
	/usr/share/fonts/100dpi/:unscaled,
	/usr/share/fonts/75dpi,
	/usr/share/fonts/100dpi,
	/usr/share/fonts/cyrillic
[    17.871] (==) ModulePath set to "/usr/lib64/xorg/modules"
[    17.871] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[    17.871] (II) Loader magic: 0x7c48e0
[    17.871] (II) Module ABI versions:
[    17.871] 	X.Org ANSI C Emulation: 0.4
[    17.871] 	X.Org Video Driver: 12.0
[    17.871] 	X.Org XInput driver : 16.0
[    17.871] 	X.Org Server Extension : 6.0
[    17.872] (--) PCI:*(0:0:2:0) 8086:0152:1458:d000 rev 9, Mem @ 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64
[    17.872] (II) Open ACPI successful (/var/run/acpid.socket)
[    17.872] (II) LoadModule: "extmod"
[    17.873] (II) Loading /usr/lib64/xorg/modules/extensions/libextmod.so
[    17.874] (II) Module extmod: vendor="X.Org Foundation"
[    17.874] 	compiled for 1.12.3, module version = 1.0.0
[    17.874] 	Module class: X.Org Server Extension
[    17.874] 	ABI class: X.Org Server Extension, version 6.0
[    17.874] (II) Loading extension MIT-SCREEN-SAVER
[    17.874] (II) Loading extension XFree86-VidModeExtension
[    17.874] (II) Loading extension XFree86-DGA
[    17.874] (II) Loading extension DPMS
[    17.874] (II) Loading extension XVideo
[    17.874] (II) Loading extension XVideo-MotionCompensation
[    17.874] (II) Loading extension X-Resource
[    17.874] (II) LoadModule: "dbe"
[    17.874] (II) Loading /usr/lib64/xorg/modules/extensions/libdbe.so
[    17.875] (II) Module dbe: vendor="X.Org Foundation"
[    17.875] 	compiled for 1.12.3, module version = 1.0.0
[    17.875] 	Module class: X.Org Server Extension
[    17.875] 	ABI class: X.Org Server Extension, version 6.0
[    17.875] (II) Loading extension DOUBLE-BUFFER
[    17.875] (II) LoadModule: "glx"
[    17.875] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so
[    17.878] (II) Module glx: vendor="X.Org Foundation"
[    17.878] 	compiled for 1.12.3, module version = 1.0.0
[    17.878] 	ABI class: X.Org Server Extension, version 6.0
[    17.878] (==) AIGLX enabled
[    17.879] (II) Loading extension GLX
[    17.879] (II) LoadModule: "record"
[    17.879] (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so
[    17.879] (II) Module record: vendor="X.Org Foundation"
[    17.879] 	compiled for 1.12.3, module version = 1.13.0
[    17.879] 	Module class: X.Org Server Extension
[    17.879] 	ABI class: X.Org Server Extension, version 6.0
[    17.879] (II) Loading extension RECORD
[    17.879] (II) LoadModule: "dri"
[    17.880] (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so
[    17.881] (II) Module dri: vendor="X.Org Foundation"
[    17.881] 	compiled for 1.12.3, module version = 1.0.0
[    17.881] 	ABI class: X.Org Server Extension, version 6.0
[    17.881] (II) Loading extension XFree86-DRI
[    17.881] (II) LoadModule: "dri2"
[    17.881] (II) Loading /usr/lib64/xorg/modules/extensions/libdri2.so
[    17.882] (II) Module dri2: vendor="X.Org Foundation"
[    17.882] 	compiled for 1.12.3, module version = 1.2.0
[    17.882] 	ABI class: X.Org Server Extension, version 6.0
[    17.882] (II) Loading extension DRI2
[    17.882] (==) Matched intel as autoconfigured driver 0
[    17.882] (==) Matched vesa as autoconfigured driver 1
[    17.882] (==) Matched fbdev as autoconfigured driver 2
[    17.882] (==) Assigned the driver to the xf86ConfigLayout
[    17.882] (II) LoadModule: "intel"
[    17.883] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so
[    17.887] (II) Module intel: vendor="X.Org Foundation"
[    17.887] 	compiled for 1.12.1, module version = 2.19.0
[    17.887] 	Module class: X.Org Video Driver
[    17.887] 	ABI class: X.Org Video Driver, version 12.0
[    17.887] (II) LoadModule: "vesa"
[    17.888] (II) Loading /usr/lib64/xorg/modules/drivers/vesa_drv.so
[    17.888] (II) Module vesa: vendor="X.Org Foundation"
[    17.888] 	compiled for 1.12.1, module version = 2.3.1
[    17.888] 	Module class: X.Org Video Driver
[    17.888] 	ABI class: X.Org Video Driver, version 12.0
[    17.888] (II) LoadModule: "fbdev"
[    17.889] (WW) Warning, couldn't open module fbdev
[    17.889] (II) UnloadModule: "fbdev"
[    17.889] (II) Unloading fbdev
[    17.889] (EE) Failed to load module "fbdev" (module does not exist, 0)
[    17.889] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
	i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
	E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
	965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
	4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
	Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
	Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
	Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
	Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
	Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
	Ivybridge Server (GT2)
[    17.890] (II) VESA: driver for VESA chipsets: vesa
[    17.890] (++) using VT number 7

[    17.895] (WW) Falling back to old probe method for vesa
[    17.895] drmOpenDevice: node name is /dev/dri/card0
[    17.895] drmOpenDevice: open result is 9, (OK)
[    17.895] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[    17.895] drmOpenDevice: node name is /dev/dri/card0
[    17.895] drmOpenDevice: open result is 9, (OK)
[    17.895] drmOpenByBusid: drmOpenMinor returns 9
[    17.895] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[    17.895] (II) intel(0): Creating default Display subsection in Screen section
	"Default Screen Section" for depth/fbbpp 24/32
[    17.895] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    17.895] (==) intel(0): RGB weight 888
[    17.895] (==) intel(0): Default visual is TrueColor
[    17.895] (II) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Desktop (GT1)
[    17.895] (--) intel(0): Chipset: "Ivybridge Desktop (GT1)"
[    17.895] (**) intel(0): Relaxed fencing enabled
[    17.895] (**) intel(0): Wait on SwapBuffers? enabled
[    17.895] (**) intel(0): Triple buffering? enabled
[    17.895] (**) intel(0): Framebuffer tiled
[    17.895] (**) intel(0): Pixmaps tiled
[    17.895] (**) intel(0): 3D buffers tiled
[    17.895] (**) intel(0): SwapBuffers wait enabled
[    17.895] (==) intel(0): video overlay key set to 0x101fe
[    17.954] (II) intel(0): Output VGA1 has no monitor section
[    17.976] (II) intel(0): Output HDMI1 has no monitor section
[    17.989] (II) intel(0): Output DP1 has no monitor section
[    18.221] (II) intel(0): Output HDMI2 has no monitor section
[    18.233] (II) intel(0): Output DP2 has no monitor section
[    18.292] (II) intel(0): EDID for output VGA1
[    18.292] (II) intel(0): Manufacturer: AOC  Model: 2450  Serial#: 11613
[    18.292] (II) intel(0): Year: 2012  Week: 38
[    18.292] (II) intel(0): EDID Version: 1.3
[    18.292] (II) intel(0): Analog Display Input,  Input Voltage Level: 0.700/0.700 V
[    18.292] (II) intel(0): Sync:  Separate
[    18.292] (II) intel(0): Max Image Size [cm]: horiz.: 52  vert.: 29
[    18.292] (II) intel(0): Gamma: 2.20
[    18.292] (II) intel(0): DPMS capabilities: Off; RGB/Color Display
[    18.292] (II) intel(0): First detailed timing is preferred mode
[    18.292] (II) intel(0): redX: 0.647 redY: 0.334   greenX: 0.284 greenY: 0.607
[    18.292] (II) intel(0): blueX: 0.151 blueY: 0.071   whiteX: 0.312 whiteY: 0.329
[    18.292] (II) intel(0): Supported established timings:
[    18.292] (II) intel(0): 720x400@70Hz
[    18.292] (II) intel(0): 640x480@60Hz
[    18.292] (II) intel(0): 640x480@67Hz
[    18.292] (II) intel(0): 640x480@72Hz
[    18.292] (II) intel(0): 640x480@75Hz
[    18.292] (II) intel(0): 800x600@56Hz
[    18.292] (II) intel(0): 800x600@60Hz
[    18.292] (II) intel(0): 800x600@72Hz
[    18.292] (II) intel(0): 800x600@75Hz
[    18.292] (II) intel(0): 832x624@75Hz
[    18.292] (II) intel(0): 1024x768@60Hz
[    18.292] (II) intel(0): 1024x768@70Hz
[    18.292] (II) intel(0): 1024x768@75Hz
[    18.292] (II) intel(0): 1280x1024@75Hz
[    18.292] (II) intel(0): Manufacturer's mask: 0
[    18.292] (II) intel(0): Supported standard timings:
[    18.292] (II) intel(0): #0: hsize: 1920  vsize 1080  refresh: 60  vid: 49361
[    18.292] (II) intel(0): #1: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    18.292] (II) intel(0): #2: hsize: 1440  vsize 900  refresh: 60  vid: 149
[    18.292] (II) intel(0): #3: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    18.292] (II) intel(0): #4: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    18.292] (II) intel(0): #5: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[    18.292] (II) intel(0): Supported detailed timing:
[    18.292] (II) intel(0): clock: 148.5 MHz   Image Size:  521 x 293 mm
[    18.292] (II) intel(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    18.292] (II) intel(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    18.292] (II) intel(0): Ranges: V min: 50 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[    18.292] (II) intel(0): Monitor name: 2450W
[    18.292] (II) intel(0): Serial No: DGJC9HA011613
[    18.292] (II) intel(0): EDID (in hex):
[    18.292] (II) intel(0): 	00ffffffffffff0005e350245d2d0000
[    18.292] (II) intel(0): 	2616010368341d782aeed1a555489b26
[    18.292] (II) intel(0): 	125054bfef00d1c0b300950081808140
[    18.292] (II) intel(0): 	81c001010101023a801871382d40582c
[    18.292] (II) intel(0): 	450009252100001e000000fd00324c1e
[    18.292] (II) intel(0): 	5311000a202020202020000000fc0032
[    18.292] (II) intel(0): 	343530570a20202020202020000000ff
[    18.292] (II) intel(0): 	0044474a43394841303131363133008b
[    18.292] (II) intel(0): EDID vendor "AOC", prod id 9296
[    18.292] (II) intel(0): Using EDID range info for horizontal sync
[    18.292] (II) intel(0): Using EDID range info for vertical refresh
[    18.292] (II) intel(0): Printing DDC gathered Modelines:
[    18.292] (II) intel(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    18.292] (II) intel(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    18.292] (II) intel(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    18.292] (II) intel(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    18.292] (II) intel(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    18.292] (II) intel(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    18.292] (II) intel(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    18.292] (II) intel(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    18.292] (II) intel(0): Modeline "1920x1080"x60.0  172.80  1920 2040 2248 2576  1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[    18.292] (II) intel(0): Modeline "1680x1050"x0.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[    18.292] (II) intel(0): Modeline "1440x900"x0.0  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz e)
[    18.292] (II) intel(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    18.292] (II) intel(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    18.292] (II) intel(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz e)
[    18.292] (II) intel(0): Printing probed modes for output VGA1
[    18.292] (II) intel(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    18.292] (II) intel(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[    18.292] (II) intel(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    18.292] (II) intel(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    18.292] (II) intel(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz e)
[    18.292] (II) intel(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    18.292] (II) intel(0): Modeline "1280x720"x60.0   74.44  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.7 kHz)
[    18.292] (II) intel(0): Modeline "1024x768"x75.1   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.1 kHz e)
[    18.292] (II) intel(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    18.292] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    18.292] (II) intel(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    18.292] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 491 520 -hsync -vsync (37.9 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    18.292] (II) intel(0): Modeline "640x480"x60.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    18.292] (II) intel(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    18.314] (II) intel(0): EDID for output HDMI1
[    18.326] (II) intel(0): EDID for output DP1
[    18.558] (II) intel(0): EDID for output HDMI2
[    18.558] (II) intel(0): Manufacturer: AOC  Model: 2450  Serial#: 11613
[    18.558] (II) intel(0): Year: 2012  Week: 38
[    18.558] (II) intel(0): EDID Version: 1.3
[    18.558] (II) intel(0): Digital Display Input
[    18.558] (II) intel(0): Max Image Size [cm]: horiz.: 52  vert.: 29
[    18.558] (II) intel(0): Gamma: 2.20
[    18.558] (II) intel(0): DPMS capabilities: Off
[    18.558] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    18.558] (II) intel(0): First detailed timing is preferred mode
[    18.558] (II) intel(0): redX: 0.647 redY: 0.334   greenX: 0.284 greenY: 0.607
[    18.558] (II) intel(0): blueX: 0.151 blueY: 0.071   whiteX: 0.312 whiteY: 0.329
 
Old 06-14-2013, 10:38 AM   #9
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
part2 of /var/log/Xorg.O.log

Code:
[    18.558] (II) intel(0): Supported established timings:
[    18.558] (II) intel(0): 720x400@70Hz
[    18.558] (II) intel(0): 640x480@60Hz
[    18.558] (II) intel(0): 640x480@67Hz
[    18.558] (II) intel(0): 640x480@72Hz
[    18.558] (II) intel(0): 640x480@75Hz
[    18.558] (II) intel(0): 800x600@56Hz
[    18.558] (II) intel(0): 800x600@60Hz
[    18.558] (II) intel(0): 800x600@72Hz
[    18.558] (II) intel(0): 800x600@75Hz
[    18.558] (II) intel(0): 832x624@75Hz
[    18.558] (II) intel(0): 1024x768@60Hz
[    18.558] (II) intel(0): 1024x768@70Hz
[    18.558] (II) intel(0): 1024x768@75Hz
[    18.558] (II) intel(0): 1280x1024@75Hz
[    18.558] (II) intel(0): Manufacturer's mask: 0
[    18.558] (II) intel(0): Supported standard timings:
[    18.558] (II) intel(0): #0: hsize: 1920  vsize 1080  refresh: 60  vid: 49361
[    18.558] (II) intel(0): #1: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    18.558] (II) intel(0): #2: hsize: 1440  vsize 900  refresh: 60  vid: 149
[    18.558] (II) intel(0): #3: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    18.558] (II) intel(0): #4: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    18.558] (II) intel(0): #5: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[    18.558] (II) intel(0): Supported detailed timing:
[    18.558] (II) intel(0): clock: 148.5 MHz   Image Size:  521 x 293 mm
[    18.558] (II) intel(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    18.558] (II) intel(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    18.558] (II) intel(0): Ranges: V min: 50 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[    18.558] (II) intel(0): Monitor name: 2450W
[    18.558] (II) intel(0): Serial No: DGJC9HA011613
[    18.558] (II) intel(0): Supported detailed timing:
[    18.558] (II) intel(0): clock: 27.0 MHz   Image Size:  521 x 293 mm
[    18.558] (II) intel(0): h_active: 720  h_sync: 736  h_sync_end 798 h_blank_end 858 h_border: 0
[    18.558] (II) intel(0): v_active: 480  v_sync: 489  v_sync_end 495 v_blanking: 525 v_border: 0
[    18.558] (II) intel(0): Supported detailed timing:
[    18.558] (II) intel(0): clock: 74.2 MHz   Image Size:  521 x 293 mm
[    18.558] (II) intel(0): h_active: 1280  h_sync: 1390  h_sync_end 1430 h_blank_end 1650 h_border: 0
[    18.558] (II) intel(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[    18.558] (II) intel(0): Supported detailed timing:
[    18.558] (II) intel(0): clock: 27.0 MHz   Image Size:  521 x 293 mm
[    18.558] (II) intel(0): h_active: 720  h_sync: 736  h_sync_end 798 h_blank_end 858 h_border: 0
[    18.558] (II) intel(0): v_active: 480  v_sync: 489  v_sync_end 495 v_blanking: 525 v_border: 0
[    18.558] (II) intel(0): Supported detailed timing:
[    18.558] (II) intel(0): clock: 27.0 MHz   Image Size:  521 x 293 mm
[    18.558] (II) intel(0): h_active: 720  h_sync: 732  h_sync_end 796 h_blank_end 864 h_border: 0
[    18.558] (II) intel(0): v_active: 576  v_sync: 581  v_sync_end 586 v_blanking: 625 v_border: 0
[    18.558] (II) intel(0): Number of EDID sections to follow: 1
[    18.558] (II) intel(0): EDID (in hex):
[    18.558] (II) intel(0): 	00ffffffffffff0005e350245d2d0000
[    18.558] (II) intel(0): 	2616010380341d782aeed1a555489b26
[    18.558] (II) intel(0): 	125054bfef00d1c0b300950081808140
[    18.558] (II) intel(0): 	81c001010101023a801871382d40582c
[    18.558] (II) intel(0): 	450009252100001e000000fd00324c1e
[    18.558] (II) intel(0): 	5311000a202020202020000000fc0032
[    18.558] (II) intel(0): 	343530570a20202020202020000000ff
[    18.558] (II) intel(0): 	0044474a433948413031313631330172
[    18.558] (II) intel(0): 	02031ef14b0514101f04130312021101
[    18.558] (II) intel(0): 	230907018301000065030c0010008c0a
[    18.558] (II) intel(0): 	d08a20e02d10103e9600092521000018
[    18.558] (II) intel(0): 	011d007251d01e206e28550009252100
[    18.558] (II) intel(0): 	001e8c0ad08a20e02d10103e96000925
[    18.558] (II) intel(0): 	210000188c0ad090204031200c405500
[    18.558] (II) intel(0): 	09252100001800000000000000000000
[    18.558] (II) intel(0): 	000000000000000000000000000000f7
[    18.558] (II) intel(0): Printing probed modes for output HDMI2
[    18.558] (II) intel(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    18.558] (II) intel(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[    18.558] (II) intel(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    18.558] (II) intel(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    18.558] (II) intel(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz e)
[    18.558] (II) intel(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    18.558] (II) intel(0): Modeline "1280x720"x60.0   74.44  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.7 kHz)
[    18.558] (II) intel(0): Modeline "1024x768"x75.1   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.1 kHz e)
[    18.558] (II) intel(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    18.558] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    18.558] (II) intel(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    18.558] (II) intel(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    18.558] (II) intel(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    18.558] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    18.558] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    18.558] (II) intel(0): Modeline "720x480"x59.9   27.00  720 736 798 858  480 489 495 525 -hsync -vsync (31.5 kHz e)
[    18.558] (II) intel(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 491 520 -hsync -vsync (37.9 kHz e)
[    18.558] (II) intel(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    18.558] (II) intel(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    18.558] (II) intel(0): Modeline "640x480"x60.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    18.558] (II) intel(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    18.709] (II) intel(0): EDID for output DP2
[    18.709] (II) intel(0): Output VGA1 connected
[    18.709] (II) intel(0): Output HDMI1 disconnected
[    18.709] (II) intel(0): Output DP1 disconnected
[    18.709] (II) intel(0): Output HDMI2 connected
[    18.709] (II) intel(0): Output DP2 disconnected
[    18.709] (II) intel(0): Using exact sizes for initial modes
[    18.709] (II) intel(0): Output VGA1 using initial mode 1920x1080
[    18.709] (II) intel(0): Output HDMI2 using initial mode 1920x1080
[    18.709] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    18.709] (II) intel(0): Kernel page flipping support detected, enabling
[    18.709] (**) intel(0): Display dimensions: (520, 290) mm
[    18.709] (**) intel(0): DPI set to (93, 94)
[    18.709] (II) Loading sub module "fb"
[    18.709] (II) LoadModule: "fb"
[    18.709] (II) Loading /usr/lib64/xorg/modules/libfb.so
[    18.711] (II) Module fb: vendor="X.Org Foundation"
[    18.711] 	compiled for 1.12.3, module version = 1.0.0
[    18.711] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    18.711] (II) Loading sub module "dri2"
[    18.711] (II) LoadModule: "dri2"
[    18.711] (II) Loading /usr/lib64/xorg/modules/extensions/libdri2.so
[    18.711] (II) Module dri2: vendor="X.Org Foundation"
[    18.711] 	compiled for 1.12.3, module version = 1.2.0
[    18.711] 	ABI class: X.Org Server Extension, version 6.0
[    18.711] (II) UnloadModule: "vesa"
[    18.711] (II) Unloading vesa
[    18.711] (==) Depth 24 pixmap format is 32 bpp
[    18.711] (II) intel(0): [DRI2] Setup complete
[    18.711] (II) intel(0): [DRI2]   DRI driver: i965
[    18.711] (II) intel(0): Allocated new frame buffer 1920x1080 stride 7680, tiled
[    18.713] (II) UXA(0): Driver registered support for the following operations:
[    18.713] (II)         solid
[    18.713] (II)         copy
[    18.713] (II)         composite (RENDER acceleration)
[    18.713] (II)         put_image
[    18.713] (II)         get_image
[    18.713] (==) intel(0): Backing store disabled
[    18.713] (==) intel(0): Silken mouse enabled
[    18.713] (II) intel(0): Initializing HW Cursor
[    18.713] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    18.714] (==) intel(0): DPMS enabled
[    18.714] (==) intel(0): Intel XvMC decoder enabled
[    18.714] (II) intel(0): Set up textured video
[    18.714] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[    18.714] (II) intel(0): direct rendering: DRI2 Enabled
[    18.714] (==) intel(0): hotplug detection: "enabled"
[    18.823] (--) RandR disabled
[    18.823] (II) Initializing built-in extension Generic Event Extension
[    18.823] (II) Initializing built-in extension SHAPE
[    18.823] (II) Initializing built-in extension MIT-SHM
[    18.823] (II) Initializing built-in extension XInputExtension
[    18.823] (II) Initializing built-in extension XTEST
[    18.823] (II) Initializing built-in extension BIG-REQUESTS
[    18.823] (II) Initializing built-in extension SYNC
[    18.823] (II) Initializing built-in extension XKEYBOARD
[    18.823] (II) Initializing built-in extension XC-MISC
[    18.823] (II) Initializing built-in extension XINERAMA
[    18.823] (II) Initializing built-in extension XFIXES
[    18.823] (II) Initializing built-in extension RENDER
[    18.823] (II) Initializing built-in extension RANDR
[    18.823] (II) Initializing built-in extension COMPOSITE
[    18.823] (II) Initializing built-in extension DAMAGE
[    18.845] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    18.845] (II) AIGLX: enabled GLX_INTEL_swap_event
[    18.845] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    18.845] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    18.845] (II) AIGLX: Loaded and initialized i965
[    18.845] (II) GLX: Initialized DRI2 GL provider for screen 0
[    18.845] (II) intel(0): Setting screen physical size to 508 x 285
[    18.948] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    18.948] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    18.948] (**) Power Button: Applying InputClass "keyboard-all"
[    18.948] (II) LoadModule: "evdev"
[    18.948] (II) Loading /usr/lib64/xorg/modules/input/evdev_drv.so
[    18.957] (II) Module evdev: vendor="X.Org Foundation"
[    18.957] 	compiled for 1.12.1, module version = 2.7.0
[    18.957] 	Module class: X.Org XInput Driver
[    18.957] 	ABI class: X.Org XInput driver, version 16.0
[    18.957] (II) Using input driver 'evdev' for 'Power Button'
[    18.957] (**) Power Button: always reports core events
[    18.957] (**) evdev: Power Button: Device: "/dev/input/event2"
[    18.957] (--) evdev: Power Button: Vendor 0 Product 0x1
[    18.958] (--) evdev: Power Button: Found keys
[    18.958] (II) evdev: Power Button: Configuring as keyboard
[    18.958] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[    18.958] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    18.958] (**) Option "xkb_rules" "evdev"
[    18.958] (**) Option "xkb_model" "evdev"
[    18.958] (**) Option "xkb_layout" "us"
[    18.958] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.972] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[    18.972] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    18.972] (**) Video Bus: Applying InputClass "keyboard-all"
[    18.972] (II) Using input driver 'evdev' for 'Video Bus'
[    18.972] (**) Video Bus: always reports core events
[    18.972] (**) evdev: Video Bus: Device: "/dev/input/event7"
[    18.972] (--) evdev: Video Bus: Vendor 0 Product 0x6
[    18.972] (--) evdev: Video Bus: Found keys
[    18.972] (II) evdev: Video Bus: Configuring as keyboard
[    18.972] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7/event7"
[    18.972] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    18.972] (**) Option "xkb_rules" "evdev"
[    18.972] (**) Option "xkb_model" "evdev"
[    18.972] (**) Option "xkb_layout" "us"
[    18.972] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.972] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    18.972] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    18.972] (**) Power Button: Applying InputClass "keyboard-all"
[    18.972] (II) Using input driver 'evdev' for 'Power Button'
[    18.972] (**) Power Button: always reports core events
[    18.972] (**) evdev: Power Button: Device: "/dev/input/event1"
[    18.972] (--) evdev: Power Button: Vendor 0 Product 0x1
[    18.972] (--) evdev: Power Button: Found keys
[    18.972] (II) evdev: Power Button: Configuring as keyboard
[    18.972] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[    18.972] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    18.972] (**) Option "xkb_rules" "evdev"
[    18.972] (**) Option "xkb_model" "evdev"
[    18.972] (**) Option "xkb_layout" "us"
[    18.972] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.972] (II) config/udev: Adding input device USB Optical Mouse (/dev/input/event3)
[    18.972] (**) USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[    18.972] (II) Using input driver 'evdev' for 'USB Optical Mouse'
[    18.972] (**) USB Optical Mouse: always reports core events
[    18.972] (**) evdev: USB Optical Mouse: Device: "/dev/input/event3"
[    18.972] (--) evdev: USB Optical Mouse: Vendor 0x4b3 Product 0x310c
[    18.972] (--) evdev: USB Optical Mouse: Found 3 mouse buttons
[    18.972] (--) evdev: USB Optical Mouse: Found scroll wheel(s)
[    18.972] (--) evdev: USB Optical Mouse: Found relative axes
[    18.972] (--) evdev: USB Optical Mouse: Found x and y relative axes
[    18.972] (II) evdev: USB Optical Mouse: Configuring as mouse
[    18.972] (II) evdev: USB Optical Mouse: Adding scrollwheel support
[    18.972] (**) evdev: USB Optical Mouse: YAxisMapping: buttons 4 and 5
[    18.972] (**) evdev: USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    18.972] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3:1.0/input/input3/event3"
[    18.972] (II) XINPUT: Adding extended input device "USB Optical Mouse" (type: MOUSE, id 9)
[    18.973] (II) evdev: USB Optical Mouse: initialized for relative axes.
[    18.973] (**) USB Optical Mouse: (accel) keeping acceleration scheme 1
[    18.973] (**) USB Optical Mouse: (accel) acceleration profile 0
[    18.973] (**) USB Optical Mouse: (accel) acceleration factor: 2.000
[    18.973] (**) USB Optical Mouse: (accel) acceleration threshold: 4
[    18.973] (II) config/udev: Adding input device USB Optical Mouse (/dev/input/mouse0)
[    18.973] (II) No input driver specified, ignoring this device.
[    18.973] (II) This device may have been added with another device file.
[    18.973] (II) config/udev: Adding input device Razer Razer BlackWidow (/dev/input/event4)
[    18.973] (**) Razer Razer BlackWidow: Applying InputClass "evdev keyboard catchall"
[    18.973] (**) Razer Razer BlackWidow: Applying InputClass "keyboard-all"
[    18.973] (II) Using input driver 'evdev' for 'Razer Razer BlackWidow'
[    18.973] (**) Razer Razer BlackWidow: always reports core events
[    18.973] (**) evdev: Razer Razer BlackWidow: Device: "/dev/input/event4"
[    18.973] (--) evdev: Razer Razer BlackWidow: Vendor 0x1532 Product 0x10e
[    18.973] (--) evdev: Razer Razer BlackWidow: Found keys
[    18.973] (II) evdev: Razer Razer BlackWidow: Configuring as keyboard
[    18.973] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input4/event4"
[    18.973] (II) XINPUT: Adding extended input device "Razer Razer BlackWidow" (type: KEYBOARD, id 10)
[    18.973] (**) Option "xkb_rules" "evdev"
[    18.973] (**) Option "xkb_model" "evdev"
[    18.973] (**) Option "xkb_layout" "us"
[    18.973] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.973] (II) config/udev: Adding input device Razer Razer BlackWidow (/dev/input/event5)
[    18.973] (**) Razer Razer BlackWidow: Applying InputClass "evdev keyboard catchall"
[    18.973] (**) Razer Razer BlackWidow: Applying InputClass "keyboard-all"
[    18.973] (II) Using input driver 'evdev' for 'Razer Razer BlackWidow'
[    18.973] (**) Razer Razer BlackWidow: always reports core events
[    18.973] (**) evdev: Razer Razer BlackWidow: Device: "/dev/input/event5"
[    18.973] (--) evdev: Razer Razer BlackWidow: Vendor 0x1532 Product 0x10e
[    18.973] (--) evdev: Razer Razer BlackWidow: Found 1 mouse buttons
[    18.973] (--) evdev: Razer Razer BlackWidow: Found scroll wheel(s)
[    18.973] (--) evdev: Razer Razer BlackWidow: Found relative axes
[    18.973] (II) evdev: Razer Razer BlackWidow: Forcing relative x/y axes to exist.
[    18.973] (--) evdev: Razer Razer BlackWidow: Found absolute axes
[    18.973] (II) evdev: Razer Razer BlackWidow: Forcing absolute x/y axes to exist.
[    18.973] (--) evdev: Razer Razer BlackWidow: Found keys
[    18.973] (II) evdev: Razer Razer BlackWidow: Configuring as mouse
[    18.973] (II) evdev: Razer Razer BlackWidow: Configuring as keyboard
[    18.973] (II) evdev: Razer Razer BlackWidow: Adding scrollwheel support
[    18.973] (**) evdev: Razer Razer BlackWidow: YAxisMapping: buttons 4 and 5
[    18.973] (**) evdev: Razer Razer BlackWidow: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    18.973] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.1/input/input5/event5"
[    18.973] (II) XINPUT: Adding extended input device "Razer Razer BlackWidow" (type: KEYBOARD, id 11)
[    18.973] (**) Option "xkb_rules" "evdev"
[    18.973] (**) Option "xkb_model" "evdev"
[    18.973] (**) Option "xkb_layout" "us"
[    18.973] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.974] (II) evdev: Razer Razer BlackWidow: initialized for relative axes.
[    18.974] (WW) evdev: Razer Razer BlackWidow: ignoring absolute axes.
[    18.974] (**) Razer Razer BlackWidow: (accel) keeping acceleration scheme 1
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration profile 0
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration factor: 2.000
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration threshold: 4
[    18.974] (II) config/udev: Adding input device Razer Razer BlackWidow (/dev/input/event6)
[    18.974] (**) Razer Razer BlackWidow: Applying InputClass "evdev pointer catchall"
[    18.974] (II) Using input driver 'evdev' for 'Razer Razer BlackWidow'
[    18.974] (**) Razer Razer BlackWidow: always reports core events
[    18.974] (**) evdev: Razer Razer BlackWidow: Device: "/dev/input/event6"
[    18.974] (--) evdev: Razer Razer BlackWidow: Vendor 0x1532 Product 0x10e
[    18.974] (--) evdev: Razer Razer BlackWidow: Found 3 mouse buttons
[    18.974] (--) evdev: Razer Razer BlackWidow: Found scroll wheel(s)
[    18.974] (--) evdev: Razer Razer BlackWidow: Found relative axes
[    18.974] (--) evdev: Razer Razer BlackWidow: Found x and y relative axes
[    18.974] (II) evdev: Razer Razer BlackWidow: Configuring as mouse
[    18.974] (II) evdev: Razer Razer BlackWidow: Adding scrollwheel support
[    18.974] (**) evdev: Razer Razer BlackWidow: YAxisMapping: buttons 4 and 5
[    18.974] (**) evdev: Razer Razer BlackWidow: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    18.974] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.2/input/input6/event6"
[    18.974] (II) XINPUT: Adding extended input device "Razer Razer BlackWidow" (type: MOUSE, id 12)
[    18.974] (II) evdev: Razer Razer BlackWidow: initialized for relative axes.
[    18.974] (**) Razer Razer BlackWidow: (accel) keeping acceleration scheme 1
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration profile 0
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration factor: 2.000
[    18.974] (**) Razer Razer BlackWidow: (accel) acceleration threshold: 4
[    18.974] (II) config/udev: Adding input device Razer Razer BlackWidow (/dev/input/mouse1)
[    18.974] (II) No input driver specified, ignoring this device.
[    18.974] (II) This device may have been added with another device file.
[    18.974] (II) config/udev: Adding input device Microsoft® LifeCam HD-3000 (/dev/input/event8)
[    18.974] (**) Microsoft® LifeCam HD-3000: Applying InputClass "evdev keyboard catchall"
[    18.974] (**) Microsoft® LifeCam HD-3000: Applying InputClass "keyboard-all"
[    18.974] (II) Using input driver 'evdev' for 'Microsoft® LifeCam HD-3000'
[    18.974] (**) Microsoft® LifeCam HD-3000: always reports core events
[    18.974] (**) evdev: Microsoft® LifeCam HD-3000: Device: "/dev/input/event8"
[    18.975] (--) evdev: Microsoft® LifeCam HD-3000: Vendor 0x45e Product 0x779
[    18.975] (--) evdev: Microsoft® LifeCam HD-3000: Found keys
[    18.975] (II) evdev: Microsoft® LifeCam HD-3000: Configuring as keyboard
[    18.975] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input8/event8"
[    18.975] (II) XINPUT: Adding extended input device "Microsoft® LifeCam HD-3000" (type: KEYBOARD, id 13)
[    18.975] (**) Option "xkb_rules" "evdev"
[    18.975] (**) Option "xkb_model" "evdev"
[    18.975] (**) Option "xkb_layout" "us"
[    18.975] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    18.975] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event9)
[    18.975] (II) No input driver specified, ignoring this device.
[    18.975] (II) This device may have been added with another device file.
[    18.975] (II) config/udev: Adding input device Speakup (/dev/input/event0)
[    18.975] (**) Speakup: Applying InputClass "evdev keyboard catchall"
[    18.975] (**) Speakup: Applying InputClass "keyboard-all"
[    18.975] (II) Using input driver 'evdev' for 'Speakup'
[    18.975] (**) Speakup: always reports core events
[    18.975] (**) evdev: Speakup: Device: "/dev/input/event0"
[    18.975] (--) evdev: Speakup: Vendor 0 Product 0
[    18.975] (--) evdev: Speakup: Found keys
[    18.975] (II) evdev: Speakup: Configuring as keyboard
[    18.975] (**) Option "config_info" "udev:/sys/devices/virtual/input/input0/event0"
[    18.975] (II) XINPUT: Adding extended input device "Speakup" (type: KEYBOARD, id 14)
[    18.975] (**) Option "xkb_rules" "evdev"
[    18.975] (**) Option "xkb_model" "evdev"
[    18.975] (**) Option "xkb_layout" "us"
[    18.975] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"

Last edited by textillis; 06-14-2013 at 10:43 AM.
 
Old 06-14-2013, 10:36 PM   #10
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,520

Rep: Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874
Code:
[    18.292] (II) intel(0): EDID for output VGA1
[    18.292] (II) intel(0): Manufacturer: AOC  Model: 2450  Serial#: 11613
Code:
[    18.558] (II) intel(0): EDID for output HDMI2
[    18.558] (II) intel(0): Manufacturer: AOC  Model: 2450  Serial#: 11613
Seems that you have two outputs connected to one monitor. What happens if you pull the VGA cable?
 
1 members found this post helpful.
Old 06-15-2013, 10:58 AM   #11
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
Not much, except:
the web cam now works,
my grub menu has been fixed (it was skipping two menu items per click),
and I hope, that when I re-install slack, it will recognize just one output
and install correctly, because, currently, it is still displaying fragmented.

THANK YOU most mostly!
For your time and kindness in getting back to me.
This is truly a classic example of gross violation of good old RTFM principle,
and for that, I owe you an apology, sincerely offered, for having wasted your time.

Cheers,
lebec
 
Old 06-15-2013, 01:20 PM   #12
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,520

Rep: Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874
No wuckers.
 
Old 06-18-2013, 07:25 AM   #13
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
GUI fragmenting on bootup

Actually, despite having solved a number of problems, the unplugging of one or the other of the second outputs for the monitor still has not solved my difficulties getting slackware to run in a gui, regardless of DE.

Anyone got any idea what this might indicate?

I have a perfect gui in both archbang and mint but regardless of which DE I try when i run slacware, I cannot get a clean gui:
all menus and their items have letters missing, to the point where after a few clicks and selections, it becomes all but unreadable.

Thanks for any ideas.
 
Old 06-18-2013, 08:34 AM   #14
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,520

Rep: Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874Reputation: 874
If the other distributions work on your hardware, then so will Slackware. The problems you describe suggest a corrupted Slackware install or missing libraries.
Are you running a full Slackware 14.0 install or did you skip some packages series?
Are you confident that the install media is OK?
Have you tried to upgrade to Slackware-current?
 
1 members found this post helpful.
Old 06-18-2013, 11:07 PM   #15
textillis
Member
 
Registered: May 2013
Location: Northern Rivers, NSW, Australia
Distribution: Slackware64-current, Mint Nadya
Posts: 299

Original Poster
Rep: Reputation: 2
Quote:
Originally Posted by allend View Post
If the other distributions work on your hardware, then so will Slackware. The problems you describe suggest a corrupted Slackware install or missing libraries.
Are you running a full Slackware 14.0 install or did you skip some packages series?
Are you confident that the install media is OK?
Have you tried to upgrade to Slackware-current?
Two things to note by way of response (thx so much for staying with me on this one!)

1. I have downloaded a fresh iso but the md5sum number doesn't match the iso!
2. Ever since my penultimate install attempt, during which I managed to get installer to wrongly "see" the contents of cdrom as a "swap-file", I now have a memtest in my grub menu (???!!!!)

I guess it is time to bite down and go for ANOTHER 2.4GB d.load of slack 14....

4 hous later: I dloaded Slack14 64-bit, again, burned it slower this time (just in case) went to boot up and noticed this time an error message flash by as first item after booting:
"error: no device ..." followed by what looks like a md5sum number, but i can't be sure and it goes by too quick to read

Last edited by textillis; 06-19-2013 at 04:01 AM. Reason: another failure to add
 
  


Reply

Tags
-current, broken, fresh, gui, hangs, installation, screen


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
[SOLVED] Upgraded to current - have a grub question Robert.Thompson Slackware 4 02-09-2011 10:56 AM
[current] rfkill upgraded? conraid Slackware 3 01-22-2011 01:02 PM
[SOLVED] upgraded current now i cannot build Slackbuilds mdynac Slackware 10 10-17-2010 10:49 AM
[SOLVED] Upgraded to 'current' and Now Have Dbus Problems, Among Others. cwizardone Slackware 6 02-23-2010 07:59 PM
Upgraded to Slack=current, now no sound! Slovak Slackware 15 11-25-2004 12:00 AM


All times are GMT -5. The time now is 06:38 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration