LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Slackware - Installation (http://www.linuxquestions.org/questions/slackware-installation-40/)
-   -   Slackware 13 on a aspire one netbook (http://www.linuxquestions.org/questions/slackware-installation-40/slackware-13-on-a-aspire-one-netbook-754080/)

faiscaheisler 09-10-2009 02:13 AM

Slackware 13 on a aspire one netbook
 
Slackware 13 donīt find my sata HD.
Slackware 12.2 have the same problem.
Slackware 12.1 ok, the HD was found under /dev/hda.

So, what is the problem? Can i install the version 12.1 and then upgrade to 13?
How did i make this upgrade?

Ismael.

MS3FGX 09-10-2009 08:23 PM

Are you using the huge kernel on Slackware 13?

faiscaheisler 09-11-2009 12:19 AM

Quote:

Originally Posted by MS3FGX (Post 3678098)
Are you using the huge kernel on Slackware 13?

I tried with huge.s and hugesmp.s
Also tried with many combinations of noacpi, noudev, nomsi, acpi=off, hda=noprobe options but the HD is not detected.

If it helps, lspci command says that i have a Intel IDE SCH Poulsbo interface and the HD is a Hitachi sata.
The netbook is a Aspire One AO751h-1340.

Today i tryed a install with one Ubuntu 9.04 iso and it works fine.

Ismael.

onebuck 09-11-2009 09:26 AM

Hi,

Quote:

Originally Posted by faiscaheisler (Post 3678233)
I tried with huge.s and hugesmp.s
Also tried with many combinations of noacpi, noudev, nomsi, acpi=off, hda=noprobe options but the HD is not detected.

If it helps, lspci command says that i have a Intel IDE SCH Poulsbo interface and the HD is a Hitachi sata.
The netbook is a Aspire One AO751h-1340.

Today i tryed a install with one Ubuntu 9.04 iso and it works fine.

Ismael.

Try passing the 'noapic' along with the 'noudev' at the boot of the installer.

When you installed Ubuntu how was the the device designated/recognized?

BTW, I do suggest that you stay within this thread to allow Diagnosis and solution.

faiscaheisler 09-11-2009 11:27 PM

Quote:

Originally Posted by onebuck (Post 3678834)
Hi,



Try passing the 'noapic' along with the 'noudev' at the boot of the installer.

When you installed Ubuntu how was the the device designated/recognized?

BTW, I do suggest that you stay within this thread to allow Diagnosis and solution.

Hi!

I tryed 'huge.s noapic noudev' and 'hugesmp.s noapic noudev' and nothing from HD.

In Ubuntu the device recognized was '/dev/sda'.

Antecipated thanks for helping!

Ismael.

onebuck 09-13-2009 08:35 AM

Hi,

When you boot Slackware then provide us with the output of 'lspci -vv'. Also what does 'dmesg |grep -i hd' & 'dmesg |grep -i sd' show?

faiscaheisler 09-14-2009 04:48 PM

Hi!

I boot with hugesmp.s without any extra parameters.
The output from 'lspci -vv' is:
Code:

00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0


00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07) (prog-if 00 [VGA controller])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 7

        Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]

        Region 1: I/O ports at 1800 [size=8]

        Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=256M]

        Region 3: Memory at b0000000 (32-bit, non-prefetchable) [size=256K]

        Expansion ROM at <unassigned> [disabled]

        Capabilities: [d0] Power Management version 2

                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [b0] Vendor Specific Information <?>

        Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-

                Address: 00000000  Data: 0000


00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 255

        Region 0: Memory at b0050000 (64-bit, non-prefetchable) [size=16K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

                        ExtTag- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

                LnkCap:        Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM L0s Enabled; Disabled- Retrain- CommClk-

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [130] Root Complex Link <?>


00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07) (prog-if 00 [Normal decode])

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

        I/O behind bridge: 00002000-00002fff

        Memory behind bridge: 88000000-880fffff

        Prefetchable memory behind bridge: d0100000-d01fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us

                        ClockPM+ Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  2, PowerLimit 6.500000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

                        Changed: MRL- PresDet- LinkState-

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [90] Subsystem: Acer Incorporated [ALI] Device 0244

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Kernel driver in use: pcieport-driver


00:1c.1 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 2 (rev 07) (prog-if 00 [Normal decode])

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0

        Memory behind bridge: d0000000-d00fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us

                        ClockPM+ Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  3, PowerLimit 6.500000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

                        Changed: MRL- PresDet- LinkState-

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [90] Subsystem: Acer Incorporated [ALI] Device 0244

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Kernel driver in use: pcieport-driver


00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 23

        Region 4: I/O ports at 1820 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin B routed to IRQ 19

        Region 4: I/O ports at 1840 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin C routed to IRQ 18

        Region 4: I/O ports at 1860 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07) (prog-if 20 [EHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin D routed to IRQ 21

        Region 0: Memory at b0054000 (32-bit, non-prefetchable) [size=1K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [58] Debug port: BAR=1 offset=00a0

        Kernel driver in use: ehci_hcd


00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-


00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07) (prog-if 80 [Master])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]

        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]

        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]

        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]

        Region 4: I/O ports at 1810 [size=16]


02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 24

        Region 0: I/O ports at 2000 [size=256]

        Region 2: Memory at d0110000 (64-bit, prefetchable) [size=4K]

        Region 4: Memory at d0100000 (64-bit, prefetchable) [size=64K]
        [virtual] Expansion ROM at d0120000 [disabled] [size=64K]

        Capabilities: [40] Power Management version 3

                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)

                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+

                Address: 00000000fee0300c  Data: 4179

        Capabilities: [70] Express (v2) Endpoint, MSI 01

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <128ns, L1 <2us

                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 4096 bytes

                DevSta:        CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us

                        ClockPM+ Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

                DevCap2: Completion Timeout: Not Supported, TimeoutDis+

                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-

                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

                        Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

                        Compliance De-emphasis: -6dB

                LnkSta2: Current De-emphasis Level: -6dB

        Capabilities: [ac] MSI-X: Enable- Count=2 Masked-

                Vector table: BAR=4 offset=00000000

                PBA: BAR=4 offset=00000800

        Capabilities: [cc] Vital Product Data

                Unknown small resource type 00, will not decode more.

        Capabilities: [100] Advanced Error Reporting

                UESta:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UEMsk:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt:        DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:        RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

                CEMsk:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

                AERCap:        First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

        Capabilities: [140] Virtual Channel <?>

        Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00

        Kernel driver in use: r8169

        Kernel modules: r8169


03:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)

        Subsystem: Foxconn International, Inc. Device e00d

        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 0

        Region 0: Memory at d0000000 (64-bit, non-prefetchable) [disabled] [size=64K]

        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-

                Address: 00000000  Data: 0000

        Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us

                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 512 bytes

                DevSta:        CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

        Capabilities: [90] MSI-X: Enable- Count=1 Masked-

                Vector table: BAR=0 offset=00000000
                PBA: BAR=0 offset=00000000

        Capabilities: [100] Advanced Error Reporting

                UESta:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-

                UEMsk:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt:        DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                CEMsk:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                AERCap:        First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

        Capabilities: [140] Virtual Channel <?>

----------------------------------------------
The output from 'dmesg | grep -i hd' is nothing.
----------------------------------------------
The output from 'dmesg | grep -i sd' is:
Driver 'sd' needs updating - please use bus_type methods
----------------------------------------------
And for more data research here is the complete output from 'dmesg':
(ops, it is too large to put in the same thread...i will put it on a separate answer...)

faiscaheisler 09-14-2009 05:10 PM

And for more data research here is the complete output from 'dmesg':

Code:

0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfd000000-0xfd003fff has been reserved
system 00:01: iomem range 0x3f800000-0xafffffff could not be reserved
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xfed00000-0xfed3ffff could not be reserved
system 00:01: iomem range 0xfed45000-0xfed4bfff has been reserved
system 00:05: ioport range 0x110-0x12e has been reserved
system 00:05: ioport range 0x374-0x375 has been reserved
system 00:05: ioport range 0x3f4-0x3f5 has been reserved
system 00:05: ioport range 0x680-0x69f has been reserved
system 00:05: ioport range 0x8080-0x8080 has been reserved
system 00:05: ioport range 0x1000-0x107f has been reserved
system 00:05: ioport range 0x1180-0x11bf has been reserved
system 00:05: ioport range 0x1640-0x164f has been reserved
system 00:05: ioport range 0xfe00-0xfe00 has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:  IO window: 0x2000-0x2fff
pci 0000:00:1c.0:  MEM window: 0x88000000-0x880fffff
pci 0000:00:1c.0:  PREFETCH window: 0x000000d0100000-0x000000d01fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:  IO window: disabled
pci 0000:00:1c.1:  MEM window: 0xd0000000-0xd00fffff
pci 0000:00:1c.1:  PREFETCH window: disabled
pci 0000:00:1c.0: enabling device (0000 -> 0003)
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: enabling device (0000 -> 0002)
pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.1: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:02: resource 0 io:  [0x2000-0x2fff]
pci_bus 0000:02: resource 1 mem: [0x88000000-0x880fffff]
pci_bus 0000:02: resource 2 mem: [0xd0100000-0xd01fffff]
pci_bus 0000:02: resource 3 mem: [0x0-0x0]
pci_bus 0000:03: resource 0 mem: [0x0-0x0]
pci_bus 0000:03: resource 1 mem: [0xd0000000-0xd00fffff]
pci_bus 0000:03: resource 2 mem: [0x0-0x0]
pci_bus 0000:03: resource 3 mem: [0x0-0x0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 13414k freed
Simple Boot Flag at 0x36 set to 0x1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Aug 17 2009 00:51:32) installed
msgmni has been set to 1720
alg: No test for cipher_null (cipher_null-generic)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
ide-cd driver 5.00
Loading iSCSI transport class v2.0-870.
rdac: device handler registered
hp_sw: device handler registered
emc: device handler registered
alua: device handler registered
fcoe_transport_register:fcoesw
Adaptec aacraid driver 1.1-5[2456]-ms
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.03.00-k4
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.3.0
Copyright(c) 2004-2008 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
      with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
stex: Promise SuperTrak EX Driver version: 3.6.0000.1
st: Version 20081215, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
pata_acpi 0000:00:1f.1: setting latency timer to 64
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xb0054000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29.6-smp ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
r8a66597_hcd: driver r8a66597_hcd, 10 Apr 2008
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    89 MB/s
raid6: int32x2    121 MB/s
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
raid6: int32x4    148 MB/s
raid6: int32x8    148 MB/s
raid6: mmxx1      179 MB/s
raid6: mmxx2      351 MB/s
raid6: sse1x1    152 MB/s
raid6: sse1x2    273 MB/s
raid6: sse2x1    292 MB/s
raid6: sse2x2    542 MB/s
raid6: using algorithm sse2x2 (542 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
Freeing unused kernel memory: 456k freed
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: New USB device found, idVendor=152e, idProduct=2507
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: Super Multi Rewriter
usb 1-2: Manufacturer: HLDS Inc.
usb 1-2: SerialNumber: P01070718004102
usb 1-2: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: New USB device found, idVendor=0c45, idProduct=62c0
usb 1-4: New USB device strings: Mfr=2, Product=1, SerialNumber=0
usb 1-4: Product: WebCam
usb 1-4: Manufacturer: Sonix Technology Co., Ltd.
usb 1-4: configuration #1 chosen from 1 choice
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: enabling device (0004 -> 0007)
r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 24 for MSI/MSI-X
eth0: RTL8102e at 0xf8524000, 00:23:8b:ee:b0:ee, XID 24c00000 IRQ 24
r8169: eth0: link down
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVD-RAM GSA-E60N 1.00 PQ: 0 ANSI: 0
sr0: scsi3-mmc drive: 125x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
usb-storage: device scan complete
usb 1-3: new high speed USB device using ehci_hcd and address 4
usb 1-3: New USB device found, idVendor=0951, idProduct=1607
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3: Product: DataTraveler 2.0
usb 1-3: Manufacturer: Kingston
usb 1-3: SerialNumber: 000AEB91BC8C5C891C120014
usb 1-3: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi 3:0:0:0: Direct-Access    Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
sd 3:0:0:0: [sda] 3905407 512-byte hardware sectors: (1.99 GB/1.86 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 3:0:0:0: [sda] Assuming drive cache: write through
sd 3:0:0:0: [sda] 3905407 512-byte hardware sectors: (1.99 GB/1.86 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 3:0:0:0: [sda] Assuming drive cache: write through
 sda:
sd 3:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete
usb 1-3: USB disconnect, address 4
usb 1-3: new high speed USB device using ehci_hcd and address 5
usb 1-3: New USB device found, idVendor=0951, idProduct=1607
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3: Product: DataTraveler 2.0
usb 1-3: Manufacturer: Kingston
usb 1-3: SerialNumber: 000AEB91BC8C5C891C120014
usb 1-3: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 4:0:0:0: Direct-Access    Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
sd 4:0:0:0: [sda] 3905407 512-byte hardware sectors: (1.99 GB/1.86 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] 3905407 512-byte hardware sectors: (1.99 GB/1.86 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sda] Assuming drive cache: write through
 sda:
sd 4:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete


onebuck 09-14-2009 06:43 PM

Hi,

Put your data or long list within vbcode tags, either # or quote.

It will make things cleaner therefore easier to aid in diagnosis.


Quote:

Originally Posted by faiscaheisler (Post 3682731)
Hi!

I boot with hugesmp.s without any extra parameters.
The output from 'lspci -vv' is:
Code:

00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0


00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07) (prog-if 00 [VGA controller])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 7

        Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]

        Region 1: I/O ports at 1800 [size=8]

        Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=256M]

        Region 3: Memory at b0000000 (32-bit, non-prefetchable) [size=256K]

        Expansion ROM at <unassigned> [disabled]

        Capabilities: [d0] Power Management version 2

                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [b0] Vendor Specific Information <?>

        Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-

                Address: 00000000  Data: 0000


00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 255

        Region 0: Memory at b0050000 (64-bit, non-prefetchable) [size=16K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

                        ExtTag- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

                LnkCap:        Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM L0s Enabled; Disabled- Retrain- CommClk-

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [130] Root Complex Link <?>


00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07) (prog-if 00 [Normal decode])

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

        I/O behind bridge: 00002000-00002fff

        Memory behind bridge: 88000000-880fffff

        Prefetchable memory behind bridge: d0100000-d01fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us

                        ClockPM+ Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  2, PowerLimit 6.500000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

                        Changed: MRL- PresDet- LinkState-

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [90] Subsystem: Acer Incorporated [ALI] Device 0244

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Kernel driver in use: pcieport-driver


00:1c.1 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 2 (rev 07) (prog-if 00 [Normal decode])

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0

        Memory behind bridge: d0000000-d00fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us

                        ClockPM+ Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  3, PowerLimit 6.500000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

                        Changed: MRL- PresDet- LinkState-

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [90] Subsystem: Acer Incorporated [ALI] Device 0244

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Kernel driver in use: pcieport-driver


00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 23

        Region 4: I/O ports at 1820 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin B routed to IRQ 19

        Region 4: I/O ports at 1840 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07) (prog-if 00 [UHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin C routed to IRQ 18

        Region 4: I/O ports at 1860 [size=32]

        Kernel driver in use: uhci_hcd


00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07) (prog-if 20 [EHCI])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin D routed to IRQ 21

        Region 0: Memory at b0054000 (32-bit, non-prefetchable) [size=1K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [58] Debug port: BAR=1 offset=00a0

        Kernel driver in use: ehci_hcd


00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-


00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07) (prog-if 80 [Master])

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]

        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]

        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]

        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]

        Region 4: I/O ports at 1810 [size=16]


02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

        Subsystem: Acer Incorporated [ALI] Device 0244

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 24

        Region 0: I/O ports at 2000 [size=256]

        Region 2: Memory at d0110000 (64-bit, prefetchable) [size=4K]

        Region 4: Memory at d0100000 (64-bit, prefetchable) [size=64K]
        [virtual] Expansion ROM at d0120000 [disabled] [size=64K]

        Capabilities: [40] Power Management version 3

                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)

                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+

                Address: 00000000fee0300c  Data: 4179

        Capabilities: [70] Express (v2) Endpoint, MSI 01

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <128ns, L1 <2us

                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 4096 bytes

                DevSta:        CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us

                        ClockPM+ Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

                DevCap2: Completion Timeout: Not Supported, TimeoutDis+

                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-

                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

                        Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

                        Compliance De-emphasis: -6dB

                LnkSta2: Current De-emphasis Level: -6dB

        Capabilities: [ac] MSI-X: Enable- Count=2 Masked-

                Vector table: BAR=4 offset=00000000

                PBA: BAR=4 offset=00000800

        Capabilities: [cc] Vital Product Data

                Unknown small resource type 00, will not decode more.

        Capabilities: [100] Advanced Error Reporting

                UESta:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UEMsk:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt:        DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:        RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

                CEMsk:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

                AERCap:        First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

        Capabilities: [140] Virtual Channel <?>

        Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00

        Kernel driver in use: r8169

        Kernel modules: r8169


03:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)

        Subsystem: Foxconn International, Inc. Device e00d

        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes

        Interrupt: pin A routed to IRQ 0

        Region 0: Memory at d0000000 (64-bit, non-prefetchable) [disabled] [size=64K]

        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-

                Address: 00000000  Data: 0000

        Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us

                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 512 bytes

                DevSta:        CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

        Capabilities: [90] MSI-X: Enable- Count=1 Masked-

                Vector table: BAR=0 offset=00000000
                PBA: BAR=0 offset=00000000

        Capabilities: [100] Advanced Error Reporting

                UESta:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-

                UEMsk:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt:        DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                CEMsk:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                AERCap:        First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

        Capabilities: [140] Virtual Channel <?>

----------------------------------------------
The output from 'dmesg | grep -i hd' is nothing.
----------------------------------------------
The output from 'dmesg | grep -i sd' is:
Driver 'sd' needs updating - please use bus_type methods
----------------------------------------------
And for more data research here is the complete output from 'dmesg':
(ops, it is too large to put in the same thread...i will put it on a separate answer...)

Notice how easy it is too scroll through the list.

You can edit your post(s) to place them within the tags by high lighting the text then choose the tag of choice.

onebuck 09-14-2009 06:49 PM

Hi,

How is the USB setup in the BIOS?

faiscaheisler 09-14-2009 09:40 PM

Quote:

Originally Posted by onebuck (Post 3682831)
Hi,

How is the USB setup in the BIOS?

Hi!

The BIOS setup is very poor, only options to set date, time, passwords, and boot order.

Ismael.

PS.: Thanks for the tips on sending big reports...

onebuck 09-15-2009 08:29 AM

Hi,

Your 'dmesg' shows a USB Flash drive plugged in. What happens when you remove that and attempt to boot the install media?

faiscaheisler 09-15-2009 04:22 PM

Quote:

Originally Posted by onebuck (Post 3683579)
Hi,

Your 'dmesg' shows a USB Flash drive plugged in. What happens when you remove that and attempt to boot the install media?

Hi,

The USB Flash that 'dmesg' shows was plugged in after i have booted and tryed to see if the HD was under /dev/sda or /dev/hda.
I plugged them to write the output from 'dmesg' in a archive to send to the forum!

The boot from slackware install dvd i made from a external USB DVD unit without the USB Flash plugged.

Ismael.

onebuck 09-15-2009 10:08 PM

Hi,

Just another shot in the dark. You did check the md5sum for download and the burnt image on the dvd? Don't rely on the burner application as the verify method. Check it, via verify on the ISO with 'md5sum' and the DVD image.

As for the 'USB', I've seen the device change the way things are recognized so that is why I question the removal.

onebuck 09-15-2009 11:16 PM

Hi,

What does 'fdisk -l' show with the USB inserted and removed. Also try 'lsusb -v' and 'lsscsi -d' and please post the output.


All times are GMT -5. The time now is 11:00 AM.