LinuxQuestions.org
Latest LQ Deal: Complete CCNA, CCNP & Red Hat Certification Training Bundle
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware > Slackware - ARM
User Name
Password
Slackware - ARM This forum is for the discussion of Slackware ARM.

Notices


Reply
  Search this Thread
Old 02-24-2017, 12:50 PM   #1
drmozes
Slackware Contributor
 
Registered: Apr 2008
Location: Surrey, England
Distribution: Slackware
Posts: 502

Rep: Reputation: 386Reputation: 386Reputation: 386Reputation: 386
Orange Pi H3 support now available in -current


Hello!

ftp://ftp.arm.slackware.com/slackwar.../ChangeLog.txt
 
Old 02-24-2017, 03:26 PM   #2
Penthux
Member
 
Registered: Dec 2008
Location: Middlesbrough, UK
Distribution: Slackware
Posts: 134

Rep: Reputation: 32
Good news. Thanks Mozes.
 
Old 02-24-2017, 11:29 PM   #3
ricky_cardo
Member
 
Registered: Feb 2006
Location: Syracuse, NY
Distribution: Slackware 14.1x86_64 and Current
Posts: 55

Rep: Reputation: 7
Good job Mozes, I installed to the internal emmc on an Orange Pi Plus2. (planning to add a sata later once I splice in power to a 3.5 inch HD. using an old PC power supply)
>installed from USB connected media (after TFTP)
- just like you stated, on the first live system boot-up ,after install with the usb removed, I had to edit /etc/fstab and change root partition.
to mmcblk1p2 I think the installer wanted it to be mmcblk2p2.


had to use a remount command on the next boot then change up the /etc/fstab (changed all mmcblk2 to 1 example:"mmcblk2p1" to "mmcblk1p1"
Code:
mount -o rw,remount /
vim /etc/fstab 
init 6


BEFORE:
Code:
rich@orange ~ $ cat /etc/fstab 
/dev/mmcblk2p1   swap             swap        defaults         0   0
/dev/mmcblk2p2   /                ext4        defaults         1   1
#/dev/cdrom      /mnt/cdrom       auto        noauto,owner,ro,comment=x-gvfs-show 0   0
/dev/fd0         /mnt/floppy      auto        noauto,owner     0   0
devpts           /dev/pts         devpts      gid=5,mode=620   0   0
proc             /proc            proc        defaults         0   0
tmpfs            /dev/shm         tmpfs       defaults         0   0

AFTER:
Code:
rich@orange ~ $ cat /etc/fstab 
/dev/mmcblk1p1   swap             swap        defaults         0   0
/dev/mmcblk1p2   /                ext4        defaults         1   1
#/dev/cdrom      /mnt/cdrom       auto        noauto,owner,ro,comment=x-gvfs-show 0   0
/dev/fd0         /mnt/floppy      auto        noauto,owner     0   0
devpts           /dev/pts         devpts      gid=5,mode=620   0   0
proc             /proc            proc        defaults         0   0
tmpfs            /dev/shm         tmpfs       defaults         0   0

Really nice work on the ethernet !!!

Last edited by ricky_cardo; 02-25-2017 at 11:36 AM. Reason: Clarity
 
Old 02-25-2017, 02:02 PM   #4
drmozes
Slackware Contributor
 
Registered: Apr 2008
Location: Surrey, England
Distribution: Slackware
Posts: 502

Original Poster
Rep: Reputation: 386Reputation: 386Reputation: 386Reputation: 386
Quote:
Originally Posted by ricky_cardo View Post
Good job Mozes, I installed to the internal emmc on an Orange Pi Plus2. (planning to add a sata later once I splice in power to a 3.5 inch HD. using an old PC power supply)
[..]
had to use a remount command on the next boot then change up the /etc/fstab (changed all mmcblk2 to 1 example:"mmcblk2p1" to "mmcblk1p1"
Code:
mount -o rw,remount /
vim /etc/fstab 
init 6
I don't see why that would happen. If you put the u-boot on to the SD card as described, then the order should be the same in the installer as it is when the newly installed OS boots.
 
Old 02-26-2017, 07:50 AM   #5
ricky_cardo
Member
 
Registered: Feb 2006
Location: Syracuse, NY
Distribution: Slackware 14.1x86_64 and Current
Posts: 55

Rep: Reputation: 7
I think this was the culprit:
I had a USBstick with the package tree connected all during setup then removed for 1st boot up. (to grab the package tree from usb rather than NFS) ((this was my plan from before the Ethernet was working)) (((now a non-issue, since Ethernet works)))

This was a good note too:
I see it is suggested to connect USB after the OS boots.

(the USB installer will not include # the package tree, just the installer image)) then you'd need to add the USB
# stick _after_ the OS has booted.


So just a user issue, good learning experience. - I didn't panic and had my towel near by
 
Old 02-26-2017, 09:14 AM   #6
drmozes
Slackware Contributor
 
Registered: Apr 2008
Location: Surrey, England
Distribution: Slackware
Posts: 502

Original Poster
Rep: Reputation: 386Reputation: 386Reputation: 386Reputation: 386
Quote:
Originally Posted by ricky_cardo View Post
I think this was the culprit:
I had a USBstick with the package tree connected all during setup then removed for 1st boot up.
But USB is not mmc, it shows as a SCSI device (/dev/sdXX). Indeed I had the same problem as I had a USB stick left plugged in from developing the USB installer image, and had to edit the fstab from the rescue shell since the system would not boot (hence the note in the INSTALL file). If you had to change the mmc device then something unexpected has happened.
 
Old 02-27-2017, 12:43 PM   #7
SCerovec
Senior Member
 
Registered: Oct 2006
Location: Cp6uja
Distribution: Slackware on x86 and arm
Posts: 1,051
Blog Entries: 2

Rep: Reputation: 123Reputation: 123
Good news (just looked up)
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
Vote for Support for the Orange Pi drmozes Slackware - ARM 2 09-18-2015 12:50 AM
Does Slackware 14.1 or Current have NFSv4 support? Altiris Slackware 6 08-08-2015 04:30 AM
Banana Pi support now in -current drmozes Slackware - ARM 1 03-09-2015 09:59 AM
RTL8191SEvB support in -current? chexmix Slackware 3 12-15-2011 07:43 AM
Xorg 7.4 support in current? rvdboom Slackware 1 10-11-2008 12:36 PM


All times are GMT -5. The time now is 06:21 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration