LinuxQuestions.org - [SOLVED] Weird: eth0 no longer recognized after upgrade & ASUS mobo replace in -current

Below is the full lspci -vvv output, should you need it:
Code:
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

        Latency: 0

        Capabilities: [e0] Vendor Specific Information <?>

        Kernel driver in use: agpgart-intel

        Kernel modules: intel-agp



00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) (prog-if 00 [VGA controller])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 26

        Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]

        Region 1: I/O ports at dc00 [size=8]

        Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]

        Region 3: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]

        Expansion ROM at <unassigned> [disabled]

        Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-

                Address: fee0300c  Data: 4181

        Capabilities: [d0] Power Management version 2

                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-



00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)

        Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 32 bytes

        Interrupt: pin A routed to IRQ 16

        Region 0: Memory at fea78000 (64-bit, non-prefetchable) [size=16K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+

                Address: 0000000000000000  Data: 0000

        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

                        ExtTag- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; Disabled- Retrain- CommClk-

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [130] Root Complex Link <?>

        Kernel driver in use: HDA Intel

        Kernel modules: snd-hda-intel



00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 32 bytes

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

        I/O behind bridge: 00001000-00001fff

        Memory behind bridge: f4000000-f41fffff

        Prefetchable memory behind bridge: 00000000f4200000-00000000f43fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us

                        ClockPM- Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  4, PowerLimit 25.000000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-

                        Changed: MRL- PresDet- LinkState-

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

                Address: fee0300c  Data: 4159

        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 8179

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [180] Root Complex Link <?>

        Kernel driver in use: pcieport

        Kernel modules: shpchp



00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) (prog-if 00 [Normal decode])

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 32 bytes

        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0

        I/O behind bridge: 0000e000-0000efff

        Memory behind bridge: feb00000-febfffff

        Prefetchable memory behind bridge: 00000000f4400000-00000000f45fffff

        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00

                DevCap:        MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag- RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 128 bytes

                DevSta:        CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap:        Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us

                        ClockPM- Surprise- LLActRep+ BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-

                SltCap:        AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+

                        Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-

                SltCtl:        Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

                SltSta:        Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

                        Changed: MRL- PresDet+ LinkState+

                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-

                RootCap: CRSVisible-

                RootSta: PME ReqID 0000, PMEStatus- PMEPending-

        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

                Address: fee0300c  Data: 4161

        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 8179

        Capabilities: [a0] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [180] Root Complex Link <?>

        Kernel driver in use: pcieport

        Kernel modules: shpchp



00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 23

        Region 4: I/O ports at d400 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin B routed to IRQ 19

        Region 4: I/O ports at d480 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin C routed to IRQ 18

        Region 4: I/O ports at d800 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin D routed to IRQ 16

        Region 4: I/O ports at d880 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin A routed to IRQ 23

        Region 0: Memory at fea77c00 (32-bit, non-prefetchable) [size=1K]

        Capabilities: [50] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [58] Debug port: BAR=1 offset=00a0

        Kernel driver in use: ehci_hcd

        Kernel modules: ehci-hcd



00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Bus: primary=00, secondary=03, subordinate=03, sec-latency=32

        I/O behind bridge: 0000f000-00000fff

        Memory behind bridge: fff00000-000fffff

        Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff

        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

        Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 8179



00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Capabilities: [e0] Vendor Specific Information <?>

        Kernel modules: iTCO_wdt, intel-rng



00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+

        Latency: 0

        Interrupt: pin A routed to IRQ 18

        Region 0: I/O ports at 01f0 [size=8]

        Region 1: I/O ports at 03f4 [size=1]

        Region 2: I/O ports at 0170 [size=8]

        Region 3: I/O ports at 0374 [size=1]

        Region 4: I/O ports at ffa0 [size=16]

        Kernel driver in use: ata_piix



00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0

        Interrupt: pin B routed to IRQ 19

        Region 0: I/O ports at d080 [size=8]

        Region 1: I/O ports at d000 [size=4]

        Region 2: I/O ports at cc00 [size=8]

        Region 3: I/O ports at c880 [size=4]

        Region 4: I/O ports at c800 [size=16]

        Capabilities: [70] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Kernel driver in use: ata_piix



00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)

        Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard

        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Interrupt: pin B routed to IRQ 19

        Region 4: I/O ports at 0400 [size=32]

        Kernel driver in use: i801_smbus

        Kernel modules: i2c-i801



01:00.0 Ethernet controller: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0)

        Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard

        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 32 bytes

        Interrupt: pin A routed to IRQ 17

        Region 0: Memory at febc0000 (64-bit, non-prefetchable) [size=256K]

        Region 2: I/O ports at ec00 [size=128]

        Capabilities: [40] Power Management version 2

                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+

                Address: 0000000000000000  Data: 0000

        Capabilities: [58] Express (v1) Endpoint, MSI 00

                DevCap:        MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited

                        ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-

                DevCtl:        Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

                        MaxPayload 128 bytes, MaxReadReq 512 bytes

                DevSta:        CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-

                LnkCap:        Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited

                        ClockPM- Surprise- LLActRep- BwNot-

                LnkCtl:        ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta:        Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

        Capabilities: [100] Advanced Error Reporting

                UESta:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-

                UEMsk:        DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt:        DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                CEMsk:        RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                AERCap:        First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

        Capabilities: [180] Device Serial Number ff-93-24-a0-90-e6-ba-ff

        Kernel driver in use: ATL1E

        Kernel modules: atl1e