LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices



Reply
 
Search this Thread
Old 02-11-2006, 10:00 AM   #1
dx0r515t
Member
 
Registered: Jan 2005
Location: USA
Distribution: Slackware 10.2 & 11.0
Posts: 155

Rep: Reputation: 30
USB gamepad configuration help


I have been searching the forums for a solution to this problem but haven't been able to find a definitive solution.

I am running slackware 10.2 on the default 2.4.31 kernel. I have a logitech precision USB gamepad. My problem is that I just can't seem to get the gamepad to work. I have modprobed these modules: joydev, hid, adi, and input.
I tried following Mega Man X's post located here:

http://www.linuxquestions.org/questi...ht=usb+gamepad

But was only able to successfully modprobe hid and adi, when I try to modprobe usb-hc I got an error message saying "can't locate module usb-hc". When I try to modprobe usb-uhci I got these errors:
Quote:
/lib/modules/2.4.31/kernel/drivers/usb/host/usb-uhci.o.gz: init_module: No such device
/lib/modules/2.4.31/kernel/drivers/usb/host/usb-uhci.o.gz: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.31/kernel/drivers/usb/host/usb-uhci.o.gz: insmod /lib/modules/2.4.31/kernel/drivers/usb/host/usb-uhci.o.gz failed
/lib/modules/2.4.31/kernel/drivers/usb/host/usb-uhci.o.gz: insmod usb-uhci failed
Here is the output of lsmod:
Quote:
Module Size Used by Tainted: PF
joydev 5568 0
adi 6008 0 (unused)
keybdev 1892 0 (unused)
mousedev 4020 0 (unused)
hid 20868 0 (unused)
input 3200 0 (autoclean) [joydev adi keybdev mousedev hid]
vmnet 21120 6
parport_pc 15044 0
parport 22824 0 [parport_pc]
vmmon 89792 0 (unused)
snd-pcm-oss 36736 1
snd-mixer-oss 12376 0 [snd-pcm-oss]
ohci1394 23888 0 (unused)
ieee1394 41636 0 [ohci1394]
snd-cmipci 17920 1
gameport 1420 0 [adi snd-cmipci]
snd-pcm 54344 0 [snd-pcm-oss snd-cmipci]
snd-opl3-lib 5860 0 [snd-cmipci]
snd-hwdep 4352 0 [snd-opl3-lib]
snd-timer 13764 0 [snd-pcm snd-opl3-lib]
snd-mpu401-uart 3136 0 [snd-cmipci]
snd-rawmidi 12480 0 [snd-mpu401-uart]
snd-seq-device 3812 0 [snd-opl3-lib snd-rawmidi]
snd 32772 0 [snd-pcm-oss snd-mixer-oss snd-cmipci snd-pcm snd-opl3-lib snd-hwdep snd-timer snd-mpu401-uart snd-rawmidi snd-seq-device]
snd-page-alloc 4712 0 [snd-mixer-oss snd-pcm snd-hwdep snd-timer snd-rawmidi snd-seq-device snd]
soundcore 3396 4 [snd]
uhci 24284 0 (unused)
ehci-hcd 17516 0 (unused)
usbcore 59148 1 [hid uhci ehci-hcd]
via-rhine 12336 1
mii 2272 0 [via-rhine]
crc32 2880 0 [via-rhine]
nvidia 3421740 6
ide-scsi 9392 0
apm 9452 2
lsusb:
Quote:
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
lspci:
Quote:
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
00:0b.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link)
00:0e.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:0f.0 RAID bus controller: Triones Technologies, Inc. HPT366/368/370/370A/372/372N (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5500] (rev a1)
dmesg:
Quote:
Linux version 2.4.31 (root@tree) (gcc version 3.3.5) #6 Sun Jun 5 19:04:47 PDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=302
Initializing CPU#0
Detected 2000.120 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3984.58 BogoMIPS
Memory: 515340k/524224k available (1832k kernel code, 8496k reserved, 607k data, 120k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2400+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xe0000000, mapped to 0xe080d000, size 1536k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:e2e0
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT366: IDE controller at PCI slot 00:0f.0
PCI: Found IRQ 10 for device 00:0f.0
PCI: Sharing IRQ 10 with 00:10.2
HPT366: chipset revision 6
HPT366: not 100% native mode: will probe irqs later
hpt: HPT372N detected, using 372N timing.
FREQ: 132 PLL: 66
hpt: no known IDE timings, disabling DMA.
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdcMA, hddio
hda: WDC WD1600BB-00DAA0, ATA DISK drive
blk: queue c03af460, I/O limit 4095Mb (mask 0xffffffff)
hdc: CR-48XGTE, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hdc: attached ide-cdrom driver.
hdc: ATAPI 54X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 < hda5 > hda2
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2866.800 MB/sec
32regs : 1920.400 MB/sec
pIII_sse : 3819.200 MB/sec
pII_mmx : 4680.800 MB/sec
p5_mmx : 5980.400 MB/sec
raid5: using function: pIII_sse (3819.200 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.8(17/11/2003)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
FAT: bogus logical sector size 0
UMSDOS: msdos_read_super failed, mount aborted.
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,2)) ...
for (ide0(3,2))
ide0(3,2):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding Swap: 995988k swap-space (priority -1)
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7676 Fri Jul 29 12:58:54 PDT 2005
via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Found IRQ 11 for device 00:12.0
PCI: Sharing IRQ 11 with 00:10.0
eth0: VIA VT6102 Rhine-II at 0xe800, 00:50:2c:07:7b:d8, IRQ 11.
eth0: MII PHY found at address 1, status 0x782d advertising 01e1 Link 45e1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 5 for device 00:10.3
PCI: Sharing IRQ 5 with 00:0b.0
PCI: Sharing IRQ 5 with 00:0e.0
ehci_hcd 00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 00:10.3: irq 5, pci mem e0e70000
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 6 ports detected
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:10.0
PCI: Sharing IRQ 11 with 00:12.0
uhci.c: USB UHCI at I/O 0xd800, IRQ 11
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:10.1
uhci.c: USB UHCI at I/O 0xdc00, IRQ 11
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:10.2
PCI: Sharing IRQ 10 with 00:0f.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 10
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:0e.0
PCI: Sharing IRQ 5 with 00:0b.0
PCI: Sharing IRQ 5 with 00:10.3
ohci1394: $Rev: 1045 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 5 for device 00:0b.0
PCI: Sharing IRQ 5 with 00:0e.0
PCI: Sharing IRQ 5 with 00:10.3
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[ee024000-ee0247ff] Max Packet=[2048]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0020e50000022c9f]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
/dev/vmmon[2703]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[2703]: Module vmmon: initialized
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
/dev/vmnet: open called by PID 2719 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 2731 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2752 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 2753 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2783 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2781 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
spurious 8259A interrupt: IRQ7.
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:53:41 Jun 5 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Also I know that the USB gamepad works, because I used it in slackware 10.0 fine, however I can't seem to get it to work in 10.2

Any ideas?

EDIT: When I try cat /dev/input/js0 I get "cat: /dev/input/js0: No such device"

Last edited by dx0r515t; 02-11-2006 at 10:12 AM.
 
Old 02-11-2006, 06:15 PM   #2
Dankles
Member
 
Registered: May 2004
Location: /dev/null
Distribution: Slackware
Posts: 245

Rep: Reputation: 31
I had a problem with a logitech gamepad once. I just upgraded the Kernel to 2.6 and had no more problems.
 
Old 02-11-2006, 11:28 PM   #3
dx0r515t
Member
 
Registered: Jan 2005
Location: USA
Distribution: Slackware 10.2 & 11.0
Posts: 155

Original Poster
Rep: Reputation: 30
Thanks for the input Dankles, I'll try kernel 2.6 if I have to.
 
Old 02-12-2006, 02:30 AM   #4
cwwilson721
Senior Member
 
Registered: Dec 2004
Location: In my house.
Distribution: Ubuntu 10.10 64bit, Slackware 13.1 64-bit
Posts: 2,649
Blog Entries: 1

Rep: Reputation: 66
Default configs don't have gamepads enabled, as modules or builtin. Just configure/compile 2.6 for what you need.
 
Old 02-12-2006, 10:56 AM   #5
dx0r515t
Member
 
Registered: Jan 2005
Location: USA
Distribution: Slackware 10.2 & 11.0
Posts: 155

Original Poster
Rep: Reputation: 30
I just thought I would let you all know, I just finished compiling 2.6.15.4 and my gamepad works now.
Thanks for the advice.
 
Old 02-12-2006, 05:59 PM   #6
Dankles
Member
 
Registered: May 2004
Location: /dev/null
Distribution: Slackware
Posts: 245

Rep: Reputation: 31
Great! Good to see that it worked.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Usb Gamepad LostNLinux Linux - General 7 05-27-2005 06:27 PM
USB Gamepad mykrob Linux - Hardware 6 08-12-2004 09:32 PM
slackware 9.1 and USB gamepad fyrebird Slackware 2 12-01-2003 11:39 AM
Need some help installing my USB gamepad hbbtstar Linux - Newbie 1 09-18-2003 09:01 PM
Need some help with my USB gamepad- Linux doesn't know what it is hbbtstar Linux - Hardware 1 09-16-2003 10:54 PM


All times are GMT -5. The time now is 04:28 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration