LinuxQuestions.org
Register a domain and help support LQ
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices



Reply
 
Search this Thread
Old 01-27-2003, 10:55 PM   #1
BittaBrotha
Member
 
Registered: Jan 2002
Location: Third Stone from the Sun
Distribution: Debian Sid, SourceMage 0.9.5, & To be Continued on a TP
Posts: 800

Rep: Reputation: 31
New Kernel Error


I've just reinstalled Slackware 8.0 with kernel 2.2.19 and once installed, it will boot fine. When I try to compile kernel 2.4.19, everything goes fine until time to reboot the system.

When it reboots, the info that displays while booting, I see something about {Disk Seek Errors} or something similar. I see a few of them and then I get the Kernel Panic errors.

I've checked and doubled check the new kernel and everything seems to look okay. Why would I get this error on the 2.4.19 kernel but not with the 2.2.19 kernel? I guess I will try downloading the 2.4.20 kernel and try that.

Also I've recompiled kernels for Slack 8.0 numerous times without this happening. But this is a different kernel then the other one's I used. Maybe it's a bad kernel, I dunno!

Any ideas/suggestions?

Thnx.
 
Old 01-27-2003, 11:01 PM   #2
trotfox
LQ Newbie
 
Registered: Jan 2003
Posts: 10

Rep: Reputation: 0
Hi Bitta Brother,
There could be numerous reason why the new Kernel is not working, It may help if you send through the error messages that you get on boot.

I don't think that the 2.4.20 kernel will give much of a change from the 2.4.19.

Possibly there are some "additional" options that need to be specified in your Kernel configuration for your hard disks to work properly.

RG
Aaron
 
Old 01-27-2003, 11:16 PM   #3
Excalibur
Senior Member
 
Registered: Jun 2002
Location: Northern VA, USA
Distribution: Ubuntu
Posts: 1,180

Rep: Reputation: 45
My first thought would be a disk error. You might try to recopy the kernel and rerun lilo. However, it could also be a DMA issue if the high speed IDE controller drivers were enabled. So you might try a kernel parameter ide=nodma to disable DMA operations. It can be done in your lilo.conf file by adding the "append = ide=nodma" statement to the new kernel section. Then run lilo to write the new boot record. Also, if the prior kernel install of lilo used the MBR to boot and the new kernel is using the partition (i.e. hda1 instead of hda for example) then the old boot loader could be trying to load from the MBR. Simply change it back to the MBR of the disk (hda) and rerun lilo to write the new MBR record.

Just a few thoughts to perhaps help isolate where the problem is. I am running 2.4.19 with Slack 8.1 and very stable other than VM issues under high memory demands. But I have those problems with 18, 19 and 20.
 
Old 01-27-2003, 11:22 PM   #4
BittaBrotha
Member
 
Registered: Jan 2002
Location: Third Stone from the Sun
Distribution: Debian Sid, SourceMage 0.9.5, & To be Continued on a TP
Posts: 800

Original Poster
Rep: Reputation: 31
Thnx for the replies...well I've done it before without any problems but then I may have left something out of the new kernel. I'm at work now but will try your suggestions when I get home in the morning.

I didn't give my hardware specs so here goes:

An AMD XP 1700 cpu, Shuttle AK31A with VIA 266 chipset, 256mb ram, 40gb Maxtor IDE HD, ATI Radeon 7200 agp video card and a DVD/CD drive.

This same setup worked once before without any problems using the 2.4.19 kernel but I did reformat my hard drive and this is when the problems began!
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Kernel Audit Support Unavaible error when booting after kernel upgrade abefroman Red Hat 2 03-21-2013 09:32 AM
Kernel compilation error: Error 15: File not found Niceman2005 Linux - General 9 10-04-2007 04:45 AM
kernel panic error after rebooting new kernel image fiero Linux - General 4 07-13-2005 09:32 AM
Kernel 2.6.7 install error, initrd-2.6.7.img error jjorloff1 Linux - General 3 09-15-2004 01:15 AM
Problem booting up new kernel. Kernel panic error... RHLinuxGUY Red Hat 2 04-11-2004 05:59 AM


All times are GMT -5. The time now is 10:25 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration