LinuxQuestions.org
View the Most Wanted LQ Wiki articles.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices

Reply
 
Search this Thread
Old 10-29-2006, 04:42 PM   #1
ganooch
Member
 
Registered: Aug 2006
Location: Dallas, TX
Distribution: Slackware 11.0
Posts: 39

Rep: Reputation: 15
Need help getting DRI to work with ATI and Slackware 11.0


I have an ATI Radeon Mobility X600 graphics card and I am trying to get DRI to work with KDE in Slackware 11.0. As you will see below, when I print glxinfo it says that DRI is not enabled. Also, glxgears only gives me ~120fps. Below is a bunch of stuff that I hope will be helpful.

My lspci:

root@chris:~# lspci
00:00.0 Host bridge: Intel Corporation 915G/P/GV/GL/PL/910GL Express Memory Controller Hub (rev 0e)
00:01.0 PCI bridge: Intel Corporation 915G/P/GV/GL/PL/910GL Express PCI Express Root Port (rev 0e)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [Radeon Mobility X600]
0b:00.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
0b:00.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
0b:00.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
0b:00.4 Class 0805: Texas Instruments PCI6411, PCI6421, PCI6611, PCI6621, PCI7411, PCI7421, PCI7611, PCI7621 Secure Digital (SD) Controller
0b:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0b:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
root@chris:~#
 
Old 10-29-2006, 04:43 PM   #2
ganooch
Member
 
Registered: Aug 2006
Location: Dallas, TX
Distribution: Slackware 11.0
Posts: 39

Original Poster
Rep: Reputation: 15
My xorg.conf:

root@chris:~# cat /etc/X11/xorg.conf
# File: xorg.conf
# File generated by fglrxconfig (C) ATI Technologies, a substitute for xf86config.

# Note by ATI: the below copyright notice is there for servicing possibly
# pending third party rights on the file format and the instance of this file.
#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# ************************************************** ********************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# ************************************************** ********************

# ************************************************** ********************
# DRI Section
# ************************************************** ********************
Section "dri"
# Access to OpenGL ICD is allowed for all users:
Mode 0666
# Access to OpenGL ICD is restricted to a specific user group:
# Group 100 # users
# Mode 0660
EndSection

# ************************************************** ********************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# ************************************************** ********************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx" # libglx.a
Load "dri" # libdri.a

EndSection

# ************************************************** ********************
# Files section. This allows default font and rgb paths to be set
# ************************************************** ********************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# ************************************************** ********************
# Server flags section.
# ************************************************** ********************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# ************************************************** ********************
# Input devices
# ************************************************** ********************

# ************************************************** ********************
# Core keyboard's InputDevice section
# ************************************************** ********************

Section "InputDevice"

Identifier "Keyboard1"
Driver "kbd"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"

EndSection


# ************************************************** ********************
# Core Pointer's InputDevice section
# ************************************************** ********************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection


#
 
Old 10-29-2006, 04:44 PM   #3
ganooch
Member
 
Registered: Aug 2006
Location: Dallas, TX
Distribution: Slackware 11.0
Posts: 39

Original Poster
Rep: Reputation: 15
xorg.conf (continued)
************************************************** ********************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# ************************************************** ********************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

#
************************************************** ********************
# Monitor section
# ************************************************** ********************

# Any number of monitor sections may be present

Section "Monitor"
Identifier "Monitor0"
# === mode lines based on GTF ===
# VGA @ 100Hz
# Modeline "640x480@100" 43.163 640 680 744 848 480 481 484 509 +hsync +vsync
# SVGA @ 100Hz
# Modeline "800x600@100" 68.179 800 848 936 1072 600 601 604 636 +hsync +vsync
# XVGA @ 100Hz
# Modeline "1024x768@100" 113.309 1024 1096 1208 1392 768 769 772 814 +hsync +vsync
# 1152x864 @ 60Hz
# Modeline "1152x864@60" 81.642 1152 1216 1336 1520 864 865 868 895 +hsync +vsync
# 1152x864 @ 85Hz
# Modeline "1152x864@85" 119.651 1152 1224 1352 1552 864 865 868 907 +hsync +vsync
# 1152x864 @ 100Hz
# Modeline "1152x864@100" 143.472 1152 1232 1360 1568 864 865 868 915 +hsync +vsync
# 1280x960 @ 75Hz
# Modeline "1280x960@75" 129.859 1280 1368 1504 1728 960 961 964 1002 +hsync +vsync
# 1280x960 @ 100Hz
# Modeline "1280x960@100" 178.992 1280 1376 1520 1760 960 961 964 1017 +hsync +vsync
# SXGA @ 100Hz
# Modeline "1280x1024@100" 190.960 1280 1376 1520 1760 1024 1025 1028 1085 +hsync +vsync
# SPEA GDM-1950 (60Hz,64kHz,110MHz,-,-): 1280x1024 @ V-freq: 60.00 Hz, H-freq: 63.73 KHz
# Modeline "GDM-1950" 109.62 1280 1336 1472 1720 1024 1024 1026 1062 -hsync -vsync
# 1600x1000 @ 60Hz
# Modeline "1600x1000" 133.142 1600 1704 1872 2144 1000 1001 1004 1035 +hsync +vsync
# 1600x1000 @ 75Hz
# Modeline "1600x1000" 169.128 1600 1704 1880 2160 1000 1001 1004 1044 +hsync +vsync
# 1600x1000 @ 85Hz
# Modeline "1600x1000" 194.202 1600 1712 1888 2176 1000 1001 1004 1050 +hsync +vsync
# 1600x1000 @ 100Hz
# Modeline "1600x1000" 232.133 1600 1720 1896 2192 1000 1001 1004 1059 +hsync +vsync
# 1600x1024 @ 60Hz
# Modeline "1600x1024" 136.385 1600 1704 1872 2144 1024 1027 1030 1060 +hsync +vsync
# 1600x1024 @ 75Hz
# Modeline "1600x1024" 174.416 1600 1712 1888 2176 1024 1025 1028 1069 +hsync +vsync
# 1600x1024 @ 76Hz
# Modeline "1600x1024" 170.450 1600 1632 1792 2096 1024 1027 1030 1070 +hsync +vsync
# 1600x1024 @ 85Hz
# Modeline "1600x1024" 198.832 1600 1712 1888 2176 1024 1027 1030 1075 +hsync +vsync
# 1920x1080 @ 60Hz
# Modeline "1920x1080" 172.798 1920 2040 2248 2576 1080 1081 1084 1118 -hsync -vsync
# 1920x1080 @ 75Hz
# Modeline "1920x1080" 211.436 1920 2056 2264 2608 1080 1081 1084 1126 +hsync +vsync
# 1920x1200 @ 60Hz
# Modeline "1920x1200" 193.156 1920 2048 2256 2592 1200 1201 1203 1242 +hsync +vsync
# 1920x1200 @ 75Hz
# Modeline "1920x1200" 246.590 1920 2064 2272 2624 1200 1201 1203 1253 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 1400x1050 @ 60Hz M9 Laptop mode
# ModeLine "1400x1050" 122.000 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync
# 1920x2400 @ 25Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@25" 124.620 1920 1928 1980 2048 2400 2401 2403 2434 +hsync +vsync
# 1920x2400 @ 30Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@30" 149.250 1920 1928 1982 2044 2400 2402 2404 2434 +hsync +vsync

EndSection


#
 
Old 10-29-2006, 04:44 PM   #4
ganooch
Member
 
Registered: Aug 2006
Location: Dallas, TX
Distribution: Slackware 11.0
Posts: 39

Original Poster
Rep: Reputation: 15
xorg.conf (continued)
************************************************** ********************
# Graphics device section
# ************************************************** ********************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# installed.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# === ATI device section ===

Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor ===
#Option "NoDDC"
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"
# === misc DRI settings ===
Option "mtrr" "off" # disable DRI mtrr mapper, driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ###
# === Screen Management ===
Option "DesktopSetup" "(null)"
Option "ScreenOverlap" "0"
Option "GammaCorrectionI" "0x00000000"
Option "GammaCorrectionII" "0x00000000"
# === OpenGL specific profiles/settings ===
Option "Capabilities" "0x00000000"
Option "CapabilitiesEx" "0x00000000"
# === Video Overlay for the Xv extension ===
Option "VideoOverlay" "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
# will be disabled automatically
Option "OpenGLOverlay" "off"
# === Center Mode (Laptops only) ===
Option "CenterMode" "off"
# === Pseudo Color Visuals (8-bit visuals) ===
Option "PseudoColorVisuals" "off"
# === QBS Management ===
Option "Stereo" "off"
Option "StereoSyncEnable" "1"
# === FSAA Management ===
Option "FSAAEnable" "yes"
Option "FSAAScale" "6"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
# === Misc Options ===
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "yes"
Option "ForceGenericCPU" "no"
BusID "PCI:1:0:0" # vendor=1002, device=3150
Screen 0
EndSection

# ************************************************** ********************
# Screen sections
# ************************************************** ********************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0 # initial origin if mode is smaller than desktop
# Virtual 1280 1024
EndSubsection
EndSection

# ************************************************** ********************
# ServerLayout sections.
# ************************************************** ********************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Server Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.

Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

Section "DRI"
Group 18 # video
# Group "dri"
Mode 0660
EndSection

### EOF ###
root@chris:~#


The output of glxinfo:

chris@chris:~$ glxinfo
name of display: :0.0
display: :0 screen: 0
direct rendering: No
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
GLX_EXT_import_context, GLX_OML_swap_method, GLX_SGI_make_current_read,
GLX_SGIS_multisample, GLX_SGIX_hyperpipe, GLX_SGIX_swap_barrier,
GLX_SGIX_fbconfig
client glx vendor string: ATI
client glx version string: 1.3
client glx extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_get_proc_address, GLX_SGI_video_sync, GLX_ARB_multisample,
GLX_ATI_pixel_format_float, GLX_ATI_render_texture
GLX extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_multisample
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.4.1)
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_texture_border_clamp,
GL_ARB_texture_cube_map, GL_ARB_texture_env_add,
GL_ARB_texture_env_combine, GL_ARB_texture_env_dot3,
GL_ARB_transpose_matrix, GL_EXT_abgr, GL_EXT_blend_color,
GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_texture_env_add,
GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
GL_EXT_texture_lod_bias
glu version: 1.3
glu extensions:
GLU_EXT_nurbs_tessellator, GLU_EXT_object_space_tess

visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
----------------------------------------------------------------------
0x23 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 1 0 None
0x24 24 tc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 1 0 None
0x25 24 tc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 1 0 None
0x26 24 tc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 1 0 None
0x27 24 dc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 1 0 None
0x28 24 dc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 1 0 None
0x29 24 dc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 1 0 None
0x2a 24 dc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 1 0 None
chris@chris:~$

glxgears;

chris@chris:~$ glxgears
612 frames in 5.0 seconds = 122.266 FPS

fglrxinfo:

chris@chris:~$ fglrxinfo
display: :0.0 screen: 0
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.4.1)

chris@chris:~$



And fgl_glxgears:

chris@chris:~$ fgl_glxgears
Using GLX_SGIX_pbuffer
X Error of failed request: BadMatch (invalid parameter attributes)
Major opcode of failed request: 142 (GLX)
Minor opcode of failed request: 5 (X_GLXMakeCurrent)
Serial number of failed request: 32
Current serial number in output stream: 32
chris@chris:~$



Please let me know if you need any other information. I would like to get DRI working so that I can try to get xgl to work with KDE.


Thanks,

ganooch
 
Old 10-29-2006, 06:36 PM   #5
Bruce Hill
HCL Maintainer
 
Registered: Jun 2003
Location: Tupelo, MS
Distribution: Gentoo
Posts: 6,926

Rep: Reputation: 124Reputation: 124
ganooch,

When you post that much stuff, use vbCodes so it's in one post, and easy to read. Just put [*code] without the * before your output, and [*/code] without the * after your output.

Check this thread and if that doesn't help, post back what you did and what you have accomplished and where you still have problems.
 
Old 10-30-2006, 11:44 AM   #6
cwwilson721
Senior Member
 
Registered: Dec 2004
Location: In my house.
Distribution: Ubuntu 10.10 64bit, Slackware 13.1 64-bit
Posts: 2,649
Blog Entries: 1

Rep: Reputation: 65
Oh, great Bruce. Refer another one to my thread about DRI....J/K

Sometimes, 'search' the forums will turn up much faster results,don't you agree?
 
Old 10-30-2006, 09:48 PM   #7
mpyusko
Member
 
Registered: Oct 2003
Location: Rochester, NY, USA
Distribution: Salckware ver 10.1 - 14.1, Debian too.
Posts: 348
Blog Entries: 1

Rep: Reputation: 36
I have to say that getting Direct Rendering enabled on my Slack box has got to be the biggest "pita" I have ever messed with.

I dowloaded the ATI driver and installed it. That wasn't enough. Somehow in the process I wound up with a /lib/modules/fglrx/build_mod directory. There, I ran the "sh ./make.sh" and found out not only did I not have a /usr/src/linux symlink, but I was also missing the /usr/src/linux/include/linux/version.h file. So I had to create it using "cd /usr/src/linux" "make include/linux/version.h"
After that I was able to go back to /lib/modules/fglrx/build_mod and run "sh ./make.sh" successfully. After that compiled, I went back to the /lib/modules/fglrx/ directory and ran "sh ./make_install.sh" that put the module into the kernel. Most of this I didn't know how to do ant it took me about 30 hours of Googling, and system reconstruction to figure out.
 
Old 10-30-2006, 09:51 PM   #8
Bruce Hill
HCL Maintainer
 
Registered: Jun 2003
Location: Tupelo, MS
Distribution: Gentoo
Posts: 6,926

Rep: Reputation: 124Reputation: 124
mpyusko,

These are some reasons most of us buy Nvidia chipset cards.
 
Old 10-30-2006, 10:52 PM   #9
mpyusko
Member
 
Registered: Oct 2003
Location: Rochester, NY, USA
Distribution: Salckware ver 10.1 - 14.1, Debian too.
Posts: 348
Blog Entries: 1

Rep: Reputation: 36
yeah, well, whenever I ask about anything HCL related, I'm told to look in the HCL. The answer "yes it works" is very rarely followed by a "but it'll take 30 hours and an Emu".
 
Old 10-30-2006, 11:58 PM   #10
Bruce Hill
HCL Maintainer
 
Registered: Jun 2003
Location: Tupelo, MS
Distribution: Gentoo
Posts: 6,926

Rep: Reputation: 124Reputation: 124
Sorry for your pain. Perhaps this will give you incentive to write better documentation for OSS for the guys coming after you.
 
Old 10-31-2006, 08:52 AM   #11
Eternal_Newbie
Member
 
Registered: Jun 2005
Location: The Pudding Isles
Distribution: Slackware 13.37
Posts: 573

Rep: Reputation: 58
In your xorg.conf:
Code:
Section "DRI"
Group 18 # video
# Group "dri"
Mode 0660
EndSection
This should probaby be:

Code:
Section "DRI"
   Mode 0666
EndSection
PS: cwwilson721's A Guide: Enabling 3D Acceleration in X11 is an incredibly useful thread. The advice in there got fglrx finally working properly on my Radeon 9600XT.

Last edited by Eternal_Newbie; 10-31-2006 at 09:00 AM.
 
Old 11-09-2006, 10:33 AM   #12
ganooch
Member
 
Registered: Aug 2006
Location: Dallas, TX
Distribution: Slackware 11.0
Posts: 39

Original Poster
Rep: Reputation: 15
I made that change to the DRI section and it didn't help. I also commented out the section with the VESA driver. glxinfo still shows no DRI and glxgears only gives ~120fps. I am open to any suggestions at this point. Also, just to rule out permissions, I checked and glxinfo shows no DRI, even while logged into the Xserver as root. Thanks in advance for any help.
 
Old 11-09-2006, 07:27 PM   #13
masonm
Senior Member
 
Registered: Mar 2003
Location: Following the white rabbit
Distribution: Slackware64 13.37 Android 4.0
Posts: 2,248

Rep: Reputation: 46
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"

Try commenting out those two options and put in

Option "DRI" "True"
 
Old 11-09-2006, 07:36 PM   #14
Eternal_Newbie
Member
 
Registered: Jun 2005
Location: The Pudding Isles
Distribution: Slackware 13.37
Posts: 573

Rep: Reputation: 58
Do you have tmpfs (POSIX Shared Memory (/dev/shm) to quote installation instruction at www.atitech.com) enabled? It's required for the ATI fglrx driver to function properly.

Add this line to your /etc/fstab file as root

Code:
tmpfs        /dev/shm        tmpfs        defaults    0   0
remember to leave a blank line at the end of the /etc/fstab

then as root
Code:
mount tmpfs
PS: Is it just me or has the ATI site gotten worse since the AMD takeover?

Last edited by Eternal_Newbie; 11-09-2006 at 07:40 PM.
 
Old 11-09-2006, 07:57 PM   #15
mpyusko
Member
 
Registered: Oct 2003
Location: Rochester, NY, USA
Distribution: Salckware ver 10.1 - 14.1, Debian too.
Posts: 348
Blog Entries: 1

Rep: Reputation: 36
Quote:
Originally Posted by Eternal_Newbie
PS: Is it just me or has the ATI site gotten worse since the AMD takeover?
for that to be true, The site would have been better before, and I think it's still just as brutal. I bought the card because it was a cheap performer. (radeon 9600 $15 a year ago.) I also saw the HCL say it works with Linux. But as I said before, "the HCL didn't tell me it would take 30+ hours and an Emu to do it." Still, I did do it, but unforunatly, I don't know what I did. The ati site was not even a factor.

Last edited by mpyusko; 11-09-2006 at 08:01 PM.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
ATI and DRI drivers help please Digitalsoldier Linux - Newbie 4 08-04-2005 10:18 PM
cannot get DRI to work with ATI fglrx drivers under X alesz Fedora 2 06-09-2005 07:39 AM
ATI 9600se running slower than older ATI card w/ DRI on euth665667 Linux - Hardware 0 07-03-2004 06:10 AM
ati problem..(DRI + tv out mix) NoirX252 Linux - Software 1 05-09-2004 01:04 PM
ATI radeon, no DRI breakerfall Linux - Hardware 3 11-11-2003 07:42 PM


All times are GMT -5. The time now is 12:47 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration