LinuxQuestions.org
Latest LQ Deal: Latest LQ Deals
Home Forums Tutorials Articles Register
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
Reload this Page kobject_register failed Any help ?
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices


Reply
  Search this Thread
Old 06-17-2005, 03:18 AM   #1
props666999
Member
 
Registered: Oct 2003
Location: Greece
Posts: 260

Rep: Reputation: 30
kobject_register failed Any help ?

dmesg reports the following error .Can i do somethink about it or just ignore it .Its usb related and the 2 final lines of the code give a radeon error maybe thats why glxinfo states No acceleration

Any help is really apreaciated

Code:
eth0: SiS 900 PCI Fast Ethernet at 0xd800, IRQ 19, 00:0d:61:57:44:2f.
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem 0xeb006000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 21, pci mem 0xeb008000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb 2-2: new full speed USB device using ohci_hcd and address 2
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
SIS5513: port 0x01f0 already claimed by ide0
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide1...
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3242
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usblp (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
agpgart: Detected SiS 746 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xd0000000
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
eth0: Media Link On 100mbps full-duplex 
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for uhci_hcd (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usblp (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
mtrr: 0xd8000000,0x8000000 overlaps existing 0xd8000000,0x1000000
mtrr: 0xd8000000,0x8000000 overlaps existing 0xd8000000,0x1000000
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:radeon_unlock] *ERROR* Process 3618 using kernel context 0
 
Old 06-17-2005, 03:36 AM   #2
keefaz
LQ Guru
 
Registered: Mar 2004
Distribution: Slackware
Posts: 6,552

Rep: Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872
I would try in a first step to put usbcore, usblp, uhci_hcd
and ehci_hcd in /etc/hotplug/blacklist (temporarly)
Then, after a reboot, I would try to load them by hand with
modprobe <module_name> for each module
If it works, you can add modprobe lines in /etc/rc.d/rc.modules
 
Old 06-17-2005, 07:17 AM   #3
props666999
Member
 
Registered: Oct 2003
Location: Greece
Posts: 260

Original Poster
Rep: Reputation: 30
I've tried to blacklist the modules but was unsucesfull so i recompiled the
kernel removing all theese modules .No i get less erors apart from the following :

Code:
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb
kobject_register failed for usblp (-17)
 [<c01fa8c7>] kobject_register+0x57/0x60
 [<c01313a7>] mod_sysfs_setup+0x77/0xe0
 [<c01325a7>] load_module+0x8a7/0xbb0
 [<c0132911>] sys_init_module+0x61/0x220
 [<c010290f>] syscall_call+0x7/0xb

usbcore appears to be the basic USB functionality in the kernel
appears on the top of the page under USB devices (Thereafter without it cannot
make the rest of the list visible )

I've got it as a module but i can add it to the kernel .
The other problem is the 3d capability

Code:
drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:radeon_unlock] *ERROR* Process 3422 using kernel context 0

Thanks in advance
 
Old 06-17-2005, 12:35 PM   #4
keefaz
LQ Guru
 
Registered: Mar 2004
Distribution: Slackware
Posts: 6,552

Rep: Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872
What is your output with :
/sbin/lspci | grep -i usb
 
Old 06-17-2005, 03:06 PM   #5
props666999
Member
 
Registered: Oct 2003
Location: Greece
Posts: 260

Original Poster
Rep: Reputation: 30
This is what come up

Code:
/sbin/lspci | grep -i usb
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
 
Old 06-18-2005, 02:33 AM   #6
keefaz
LQ Guru
 
Registered: Mar 2004
Distribution: Slackware
Posts: 6,552

Rep: Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872
Did you enable usb hid driver in config ?
--USB Human Interface Device (full HID) support
--HID input layer support

Also what is your output, from the kernel directory
with :
grep -v ^# .config | grep -i usb
 
Old 06-18-2005, 11:17 AM   #7
props666999
Member
 
Registered: Oct 2003
Location: Greece
Posts: 260

Original Poster
Rep: Reputation: 30
USB Human Interface Device (full HID) support is not selected at all

and the output from the command is :

CONFIG_USB=m
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_HAS_OHCI=y
CONFIG_USB_PRINTER=m
 
Old 06-18-2005, 01:30 PM   #8
keefaz
LQ Guru
 
Registered: Mar 2004
Distribution: Slackware
Posts: 6,552

Rep: Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872Reputation: 872
Try recompile the kernel with HID
also add HIDINPUT, EHCI_HCD and UHCI_HCD as modules
maybe add USB_STORAGE, up to you
 
Old 06-22-2005, 07:20 AM   #9
props666999
Member
 
Registered: Oct 2003
Location: Greece
Posts: 260

Original Poster
Rep: Reputation: 30
HIDINPUT is added on the kernel ( but don't use any usb mice keyboard though

apart from that dmesg reports no errors .

Thanks keefaz
 
Old 07-08-2005, 01:15 PM   #10
mrIgli
LQ Newbie
 
Registered: May 2004
Distribution: Mandrake and Gentoo
Posts: 3

Rep: Reputation: 0
I'm not sure about the USB stuff, but wrt to the Radeon, I'm having the same problem. AFAICT it's something to do with having the correct AGP bridge drivers, at least in my case. Check out the DRI Wiki for more info.

First though, the stuff about mtrr overlap; I fixed this on mine by starting linux non-fb (the framebuffer is using the same range.) This may be your only problem as your agp_gart is starting fine.
 
  


Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bind9: NDC command failed : rndc: connect failed: connection refused Boudewijn Linux - Networking 19 01-02-2014 07:19 AM
Weird dmesg output. [<c01b16f3>] kobject_register+0x43/0x50 gian2oo1 Slackware 1 07-27-2005 12:11 AM
online_update failed - ERROR(Media:connection failed)[Connect failed] rover SUSE / openSUSE 8 02-22-2005 07:57 AM
unpacking of archive failed: cpio: read failed-input/output error rafc Linux - Newbie 0 04-21-2004 09:03 AM
Loosing CD Drive while installing Mandrake 9.2 (ldconfig failed or idconfig failed) sjzabel Linux - General 3 02-26-2004 04:35 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware

All times are GMT -5. The time now is 04:59 PM.

Contact Us - Advertising Info - Rules - Privacy - LQ Merchandise - Donations - Contributing Member - LQ Sitemap -
Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration