LinuxQuestions.org
Visit Jeremy's Blog.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices

Reply
 
Search this Thread
Old 07-15-2004, 09:01 PM   #1
kntgtaid
LQ Newbie
 
Registered: Jul 2003
Distribution: Slackware 9.0
Posts: 17

Rep: Reputation: 0
enlightenment sound does not work, but sound works for other apps????


I recently upgraded from slack 8 to 9.1 (big headache!). The problem I am seeing is that I enable audio for enlightenment and I never hear anything. If I start up xmms or mplayer I get sound.

================================================================
here is my lsmod:
Module Size Used by Tainted: P
nvidia 1968064 12 (autoclean)
parport_pc 14724 0
parport 23264 0 [parport_pc]
uhci 24496 0 (unused)
usbcore 58400 0 [uhci]
3c59x 26832 1
ide-scsi 9424 0
snd-ens1371 13380 0
gameport 1452 0 [snd-ens1371]
snd-rawmidi 14592 0 [snd-ens1371]
snd-seq-device 4320 0 [snd-rawmidi]
snd-ac97-codec 52076 0 [snd-ens1371]
snd-pcm-oss 46408 0
snd-pcm 67360 0 [snd-ens1371 snd-pcm-oss]
snd-timer 16100 0 [snd-pcm]
snd-page-alloc 6936 0 [snd-pcm]
snd-mixer-oss 14392 0 [snd-pcm-oss]
snd 38468 0 [snd-ens1371 snd-rawmidi snd-seq-device snd-ac97-codec snd-pcm-oss snd-pcm snd-timer snd-mixer-oss]
soundcore 3332 6 [snd]
agpgart 39576 3
================================================================

here is cat /proc/pci

PCI devices found:
Bus 0, device 0, function 0:
Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 196
).
Prefetchable 32 bit memory at 0xe0000000 [0xe3ffffff].
Bus 0, device 1, function 0:
PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (
rev 0).
Master Capable. No bursts. Min Gnt=12.
Bus 0, device 7, function 0:
ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 34).
Bus 0, device 7, function 1:
IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PI
PC Bus Master IDE (rev 16).
Master Capable. Latency=32.
I/O at 0xd000 [0xd00f].
Bus 0, device 7, function 2:
USB Controller: VIA Technologies, Inc. USB (rev 16).
IRQ 10.
Master Capable. Latency=32.
I/O at 0xd400 [0xd41f].
Bus 0, device 7, function 3:
USB Controller: VIA Technologies, Inc. USB (#2) (rev 16).
IRQ 10.
Master Capable. Latency=32.
I/O at 0xd800 [0xd81f].
Bus 0, device 7, function 4:
Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 48).
IRQ 9.
Bus 0, device 16, function 0:
Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 7).
IRQ 9.
Master Capable. Latency=32. Min Gnt=12.Max Lat=128.
I/O at 0xdc00 [0xdc3f].
Bus 0, device 17, function 0:
Ethernet controller: 3Com Corporation 3c900B-TPO [Etherlink XL TPO] (rev 4).
IRQ 11.
Master Capable. Latency=32. Min Gnt=10.Max Lat=48.
I/O at 0xe000 [0xe07f].
Non-prefetchable 32 bit memory at 0xe7000000 [0xe700007f].
Bus 1, device 0, function 0:
VGA compatible controller: nVidia Corporation NV17 [GeForce4 MX 440] (rev 16
3).
IRQ 10.
Master Capable. Latency=248. Min Gnt=5.Max Lat=1.
Non-prefetchable 32 bit memory at 0xe4000000 [0xe4ffffff].
Prefetchable 32 bit memory at 0xd0000000 [0xd7ffffff].
Prefetchable 32 bit memory at 0xd8000000 [0xd807ffff].
================================================================

in order to get the sound working for the other applications I put the following into /etc/rc.d/rc.modules:

/sbin/modprobe snd-pcm-oss
/sbin/modprobe snd-ens1371

================================================================
here is my dmesg, I don't see anything specific abou the snd-ens1371 (which I used to with slack 8 on startup) . The only line I see having anything to do with the card is "PCI: Found IRQ 9 for device 00:10.0".

Linux version 2.4.22 (root@midas) (gcc version 3.2.3) #6 Tue Sep 2 17:43:01 PDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
DMI not present.
Kernel command line: auto BOOT_IMAGE=Linux ro root=302 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 651.505 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1297.61 BogoMIPS
Memory: 515364k/524224k available (1813k kernel code, 8472k reserved, 614k data, 116k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb390, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI: Via IRQ fixup for 00:07.3, from 255 to 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xd0000000, mapped to 0xe080d000, size 1536k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:f910
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdcMA, hddio
hda: WDC WD400EB-00CPF0, ATA DISK drive
hdb: Maxtor 6Y080P0, ATA DISK drive
blk: queue c03a9d80, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03a9ebc, I/O limit 4095Mb (mask 0xffffffff)
hdc: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(33)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=9964/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3 hda4
hdb: hdb1
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 1077.600 MB/sec
32regs : 646.000 MB/sec
pIII_sse : 1334.400 MB/sec
pII_mmx : 1460.400 MB/sec
p5_mmx : 1523.600 MB/sec
raid5: using function: pIII_sse (1334.400 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 116k freed
Adding Swap: 1028120k swap-space (priority -1)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xe0000000
PCI: Found IRQ 9 for device 00:10.0
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-52327S Rev: QS03
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
PCI: Found IRQ 11 for device 00:11.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:11.0: 3Com PCI 3c900 Cyclone 10Mbps TPO at 0xe000. Vers LK1.1.18-ac
00:50:da:11:a1:46, IRQ 11
product code 5751 rev 00.4 date 08-03-99
Internal config register is 1800000, transceivers 0x8.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 182d.
Enabling bus-master transmits and whole-frame receives.
00:11.0: scatter/gather enabled. h/w checksums enabled
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Assigned IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:07.3
uhci.c: USB UHCI at I/O 0xd400, IRQ 10
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:07.3
PCI: Sharing IRQ 10 with 00:07.2
uhci.c: USB UHCI at I/O 0xd800, IRQ 10
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 [PCSPP,EPP]
parport_pc: Via 686A parallel port: io=0x378
lp0: using parport0 (polling).
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-5328 Wed Dec 17 13:54:51 PST 2003


================================================================

My soundcard was muted in the to start off, so I had to load alsactl restore during start up in rc.local

================================================================

I have configured enlightenment with sound, downloaded and installed the latest versions for esound, and alsa-drivers, but no luck.

Does anybody have any ideas on what I can try next to get E's sound working?

Thanks

Bryan

Last edited by kntgtaid; 07-15-2004 at 10:05 PM.
 
Old 07-16-2004, 04:50 PM   #2
kntgtaid
LQ Newbie
 
Registered: Jul 2003
Distribution: Slackware 9.0
Posts: 17

Original Poster
Rep: Reputation: 0
Tested X with KDE and sound started up. My guess is something with esd???
 
Old 07-17-2004, 01:50 AM   #3
320mb
Senior Member
 
Registered: Nov 2002
Location: pikes peak
Distribution: Slackware, LFS
Posts: 2,577

Rep: Reputation: 47
Re: enlightenment sound does not work, but sound works for other apps????

Quote:
Originally posted by kntgtaid
I recently upgraded from slack 8 to 9.1 (big headache!).
that's a big jump, you should have just done a complete re-install to a "clean" partition.............

less headaches that way.
 
Old 07-17-2004, 06:08 AM   #4
kntgtaid
LQ Newbie
 
Registered: Jul 2003
Distribution: Slackware 9.0
Posts: 17

Original Poster
Rep: Reputation: 0
Quote:
that's a big jump, you should have just done a complete re-install to a "clean" partition.............
sorry, didn't mean to cause confusion, when I said that I upgraded to 9.1 I did format and to a complete new install from scratch.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Startup Sound Works... CD Sound Doesn't Work... GNewbie MEPIS 8 01-02-2006 10:35 PM
Running apps within enlightenment brings up KDE/Gnome ColKurtz Linux - Software 0 01-24-2005 12:11 PM
sound works for desktop but not other apps dauphinfay Linux - Newbie 9 11-10-2004 12:45 AM
Sound doesn't work with Enlightenment enigma Z Linux - Software 0 09-15-2004 06:43 PM
Need help getting Enlightenment to work. Kyral Retsam Linux - Software 2 07-27-2004 03:43 PM


All times are GMT -5. The time now is 10:31 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration