Alright, as far as I can tell ATI.com doesnt have a linux driver for a 7500 radeon 64mb card. How can I check to see if gl, dri, or whatever required for perfomance, is loaded? The bois of my a7n8x has agp up to 8x enabled ( i know, the card only does 4x), just curious if my system need any further settings than what is being run stock on my default kernel slack 10...
much thanks

type glxinfo in a X session, more info available here http://dri.sourceforge.net/cgi-bin/moin.cgi/ and here http://gatos.sourceforge.net/

alright, I have dri an gl running now. thank you.
Im at about 140 FPS on full screen, but thats alright. This is just for playing Neverwinter nights every once in a while. Thank you

can we have a look at your xorg.conf or x86free.conf

sorry for getting back so late but yes here it is, it an xorgconfig, so its a bit lengthy:

Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "speedo"
Load "freetype"
# Load "xtt"

# This loads the GLX module
Load "glx"
# This loads the DRI module
Load "dri"

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/TTF/"
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for X.Org
# Option "XkbRules" "__XKBDEFRULES__"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xorg"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/mouse"
Option "ZAxisMapping""4 5"

# Mouse-speed setting for PS/2 mouse.

# Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

Identifier "nec"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 31.5 - 57.0

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 50-90

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# Device configured by xf86config:

Section "Device"
Identifier "7500 radeon"
Driver "radeon"
#VideoRam 65536
# Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "7500 radeon"
Monitor "nec"
DefaultDepth 24

Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

Section "DRI"
Mode 0666
EndSection

like i said, sorry for the length. If its commented out, can i just remove the line from the file to shorten it up a bit?

thanks...

i get around 204fps on glxgears full screen

6252 frames in 5.0 seconds = 1250.400 FPS
3458 frames in 5.0 seconds = 691.600 FPS
964 frames in 5.0 seconds = 192.800 FPS
1020 frames in 5.0 seconds = 204.000 FPS
1020 frames in 5.0 seconds = 204.000 FPS
1020 frames in 5.0 seconds = 204.000 FPS

oh, thats great and all, but that doesnt realy help me out. Nice though...

the command is $glxinfo
and if direct rendering says yes, that mean hardware acceleration is on...

Option "AGPMode" "4"
Option "AGPFastWrite" "on"
Option "EnablePageFlip" "on"

adding the following did also help...

bash-2.05b$ glxinfo
name of display: :0.0
display: :0 screen: 0
direct rendering: No
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
GLX_EXT_import_context, GLX_SGI_make_current_read, GLX_SGIS_multisample
client glx vendor string: SGI
client glx version string: 1.2
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_allocate_memory,
GLX_MESA_swap_control, GLX_MESA_swap_frame_usage, GLX_OML_swap_method,
GLX_OML_sync_control, GLX_SGI_make_current_read, GLX_SGI_swap_control,
GLX_SGI_video_sync, GLX_SGIS_multisample, GLX_SGIX_fbconfig,
GLX_SGIX_visual_select_group
GLX extensions:
GLX_ARB_get_proc_address, GLX_EXT_import_context, GLX_EXT_visual_info,
GLX_EXT_visual_rating
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.4 Mesa 5.0.2)

blah blah blah....ther is more, but I will try
Option "AGPMode" "4"
Option "AGPFastWrite" "on"
Option "EnablePageFlip" "on"
when I get home from work, thanks again!

I added the lines you suggested, but I still get the
Direct Rendering: no line in glxinfo
might there be a module or something missing from the kernel that I might need?

I am running the default slack 10 bare.i at the moment

is the agpgart.o module loaded?

i did an lsmod and its shows up as a listing in this way:

agpgart 43940 0 (unused)


then, as root I did a modprobe, still the same. Isn't there a rc/ directory to check for modules?

/etc/rc.d/rc.modules

ne ways... i'll have to wait till i get ma desktop back from repairs to give us a full sp about the ati issue...