LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Slackware (http://www.linuxquestions.org/questions/slackware-14/)
-   -   20.1" Flat Panel LCD Artifacts @startup Problem (http://www.linuxquestions.org/questions/slackware-14/20-1-flat-panel-lcd-artifacts-%40startup-problem-600214/)

NightSky 11-16-2007 04:19 PM

20.1" Flat Panel LCD Artifacts @startup Problem
 
Getting Monitor Artifacts at XFCE startup issue: ATI Rage 128 Pro. Running Xfce with hugesmp.s kernel can't compile kernel if I cant get xorg configured right.

Do u think I shouldn't be using slackware12? Hope this is all not too much.

1. I don't know what my LCD Monitor Dot Frequency Clock is and there is no mention of it in its manual.

2. What is the refresh rate? Is it the same as monitor's response time, ie.25ms?

Monitor Auto Self adjusts, No software Driver. When I tried to generate a modeline using, (http://xtiming.sourceforge.net/cgi-bin/xtiming.pl this is what) I got:

Use this modeline at your own risk.
Modeline "1600x1200@59" 174.01 1600 1632 2288 2320 1200 1224 1236 1261
Horizontal sync frequency: 75 kHz
This is not encouraging!
Warning!
# Horizontal sync frequency below minimum of 79.976kHz!
# Horizontal sync frequency above maximum of 31.475kHz!
# Refresh rate below minimum of 75.024Hz!

Don't understand the Warning Lines? They don't make sense because the manual states Frequency range is: FH:31.469~79.97Khz
FV:59.9~75.0240Hz

What is more important to have the most accurate the Horizontal or Veritical refresh rates?

simcox1 11-17-2007 04:15 AM

Issue this command.

cat /etc/X11/xorg.conf

And copy/paste it to here. If using xterm, highlight the page by holding down the left mouse button, and paste with middle button.

H_TeXMeX_H 11-17-2007 05:50 AM

Try running 'xorgsetup', it will help you get a usable configuration.

NightSky 11-17-2007 11:26 PM

MY Xorgconfig Settings
 
Quote:

Originally Posted by simcox1 (Post 2961799)
Issue this command.

cat /etc/X11/xorg.conf

And copy/paste it to here. If using xterm, highlight the page by holding down the left mouse button, and paste with middle button.

Code:

cat /etc/X11/xorg.conf
# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"  # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
    Load      "glx"
# This loads the DRI module
    Load      "dri"
EndSection


# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

#    RgbPath    "/usr/share/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#

    FontPath  "/usr/share/fonts/TTF"
    FontPath  "/usr/share/fonts/OTF"
    FontPath  "/usr/share/fonts/Type1"
    FontPath  "/usr/share/fonts/misc"
    FontPath  "/usr/share/fonts/75dpi/:unscaled"
#    FontPath  "/usr/lib/X11/fonts/local/"
    FontPath  "/usr/lib/X11/fonts/misc/"
    FontPath  "/usr/lib/X11/fonts/75dpi/:unscaled"
    FontPath  "/usr/lib/X11/fonts/100dpi/:unscaled"
    FontPath  "/usr/lib/X11/fonts/Speedo/"
    FontPath  "/usr/lib/X11/fonts/Type1/"
    FontPath  "/usr/lib/X11/fonts/TTF/"
    FontPath  "/usr/lib/X11/fonts/OTF/"
    FontPath  "/usr/lib/X11/fonts/cyrillic/"
    FontPath  "/usr/lib/X11/fonts/75dpi/"
    FontPath  "/usr/lib/X11/fonts/100dpi/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/lib/xorg/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Ctrl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Ctrl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Ctrl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier  "Keyboard1"
    Driver      "kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option    "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option    "Xleds"      "1 2 3"

#    Option "LeftAlt"    "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"  "de"
# or:
#    Option "XkbLayout"  "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"  "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"  "xorg"
    Option "XkbModel"  "logicdpa"
    Option "XkbLayout"  "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier  "Mouse1"
    Driver      "mouse"
    Option "Protocol"    "Auto" # Auto detect
    Option "Device"      "/dev/input/mice"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"  "Xqueue"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"        "256"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"  "9600"
#    Option "SampleRate"        "150"

# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.  Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.

    Option "ZAxisMapping"  "4 5 6 7"

# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver    "magellan"
#    Option    "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver    "spaceorb"
#    Option    "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver    "microtouch"
#    Option    "Device"        "/dev/ttyS0"
#    Option    "MinX"          "1412"
#    Option    "MaxX"          "15184"
#    Option    "MinY"          "15372"
#    Option    "MaxY"          "1230"
#    Option    "ScreenNumber"  "0"
#    Option    "ReportingMode" "Scaled"
#    Option    "ButtonNumber"  "1"
#    Option    "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver    "elo2300"
#    Option    "Device"        "/dev/ttyS0"
#    Option    "MinX"          "231"
#    Option    "MaxX"          "3868"
#    Option    "MinY"          "3858"
#    Option    "MaxY"          "272"
#    Option    "ScreenNumber"  "0"
#    Option    "ReportingMode" "Scaled"
#    Option    "ButtonThreshold"      "17"
#    Option    "ButtonNumber"  "1"
#    Option    "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "SYNAPS, Composite, DPMS"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync  31-79

#    HorizSync  30-64        # multisync
#    HorizSync  31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync  15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 59-75

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier  "Standard VGA"
    VendorName  "Unknown"
    BoardName  "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset    "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver    "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam  256

#    Clocks    25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "ATI RAGE 128 PRO, 32M, AGP"
    Driver      "r128"
    #VideoRam    32000
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "ATI RAGE 128 PRO, 32M, AGP"
    Monitor    "SYNAPS, Composite, DPMS"
    DefaultDepth 24

    Subsection "Display"
        Depth      8
        Modes      "1600x1200" "1280x1024" "1024x768"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth      16
        Modes      "1600x1200" "1280x1024" "1024x768"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth      24
        Modes      "1600x1200" "1280x1024" "1024x768"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

 Section "DRI"
    Mode 0666
EndSection

Do I run xorsetup as root or user? Maybe all I need is to enter Display Demensions and an accurate modeline? Thanks you guys are great.

H_TeXMeX_H 11-18-2007 05:39 AM

run 'xorgsetup' as root, while X is not running.

simcox1 11-18-2007 10:12 AM

Quote:

Warning!
# Horizontal sync frequency below minimum of 79.976kHz!
# Horizontal sync frequency above maximum of 31.475kHz!
# Refresh rate below minimum of 75.024Hz!
It might just be that you need to set more exact horiz and vert refresh rates. So maybe change it to this:

HorizSync 31.475 - 79.976
VertRefresh 59.9 - 75.024


Or round them up rather than down.

NightSky 11-18-2007 10:32 PM

My optimal 1600x1200 @
Horizontal Frequency 75.00KHz
Vertical Frequency 60.00Hz
I will try your suggestions. Thanks

NightSky 11-19-2007 02:41 AM

How do I revert to xorgconfig backup file?
 
Quote:

Originally Posted by H_TeXMeX_H (Post 2962848)
run 'xorgsetup' as root, while X is not running.

Ran 'xorgsetup' as root and monitor artifacts increased at the startup of xfce.

Can u tell me how to revert to previous xorgconfig
file(backup file). Thanks

Alien_Hominid 11-19-2007 04:23 AM

1) Kernel compilation is not related to X.
2) Check /etc/X11 for xorg.conf~ or smth similar
Code:

cd /etc/X11
ls


H_TeXMeX_H 11-19-2007 04:23 AM

There should be an 'xorg.conf.backup'.

Alien_Hominid 11-19-2007 04:39 AM

You can also try xorgconfig but I recommend setting things manually.

tobyl 11-19-2007 04:48 AM

Hi NightSky,

The xorg.conf that you posted had two device sections, one stating the driver was "vga" the other said "r128"
I think "r128" is the correct one, and personally I would comment out or remove the reference to vga in case the wrong driver is getting loaded.
You could check that the correct driver is being loaded (and for errors) by looking at /var/log/Xorg.0.log

tobyl

NightSky 11-19-2007 01:18 PM

How do I change it back?
 
Quote:

Originally Posted by H_TeXMeX_H (Post 2963821)
There should be an 'xorg.conf.backup'.

I am qcommandline beginner user.*

There is an xorgconfig backup file, but I don't know how to change it back? Please explain, like this:

1. Find the path in XFCE GUI
2. Logout of GUI
3. commandline su root
4.
Code:

cd /etc/X11/xorg.conf
? 5. vi xorg.conf ?
? 6. delete the backup extension and replace it with what?
? 7. delete current xorgconfig ?
? 8. :wq ?


tobyl: "r128" is the correct driver for my video card.

I thought the following section is just for discriptive purposes?
# Graphics device sections:
# Standard VGA Device:"
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
Is the above just a discriptive example, automatically generated?


Should I remove # from videoram and what are clock lines?
# Device configured by xorgconfig:

Section "Device"
Identifier "ATI RAGE 128 PRO, 32M, AGP"
Driver "r128"
#VideoRam 32000 (remove # ..?)
# Insert Clocks lines here if appropriate (What are clock lines?)
EndSection

tobyl 11-19-2007 02:12 PM

NightSky,

Lines beginning with # and whitespace are ignored, so you effectively have

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
Driver "vga"
EndSection

Section "Device"
Identifier "ATI RAGE 128 PRO, 32M, AGP"
Driver "r128"
EndSection

I believe the last entry will be the one thats used anyway, but its a good idea to keep things clean and simple, so comment out with # the entries you dont want.
The video memory entry is commented out by xorgconfig on purpose.You only need to uncomment it if the system reads the amount of video ram incorrectly

If you want to change a file's name from the command line, you use the mv command, something like this


su (root)
cd /etc/X11
mv xorg.conf xorg.conf.old
mv xorg.conf.backup xorg.conf

tobyl

edit: i'm not sure if Vendorname and Boardname are required entries or not (i doubt it) but in any case you can write whatever you like for those entries. Some xorg config programs interrogate the video card and put entries in there, but they are basically just informational if you only have one video card.

edit2:
Ok, one more thing, if you want to edit files from the command line, but are not used to vi or vim, it is just too much to master right now, you can learn that later. Instead use nano. Eg
(as root)
# nano /etc/X11/xorg.conf

its as easy as notepad! (ctrl+x to exit)

NightSky 11-19-2007 08:43 PM

Found EE and WW
 
Super Thanks, I am comfortable using Vi with Old Slackware Book instructions.
I am commands defficient.

Commenting out: Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
Driver "vga"
EndSection ---> resulted in no screen error...
Added video crd info and StartX worked. 1/4"-1/2" color artifact band across top of display persists. Found Display EE and WW - how do I fix them? Thanks


Code:


cat /var/log/Xorg.0.log

(II) Setting vga for screen 0.
(II) R128(0): PCI bus 1 card 0 func 0
(**) R128(0): Depth 24, (--) framebuffer bpp 32
(II) R128(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) R128(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
        compiled for 1.3.0, module version = 0.1.0
        ABI class: X.Org Video Driver, version 1.2
(II) R128(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) R128(0): RGB weight 888
(II) R128(0): Using 8 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
        compiled for 1.3.0, module version = 1.0.0
        ABI class: X.Org Video Driver, version 1.2
(II) R128(0): initializing int10
(II) R128(0): Primary V_BIOS segment is: 0xc000
(--) R128(0): Chipset: "ATI Rage 128 Pro ULTRA TF (AGP)" (ChipID = 0x5446)
(--) R128(0): Linear framebuffer at 0xd4000000
(--) R128(0): MMIO registers at 0xd9000000
(--) R128(0): VideoRAM: 32768 kByte (128-bit SDR SGRAM 1:1)

(**) R128(0): Using external CRT for display -->? Problem? Using FlatPanel ?
(II) R128(0): Primary Display == Type 3
(WW) R128(0): Can't determine panel dimensions, and none specified.-->? Problem?
        Disabling programming of FP registers. --> ? 411 310 display size
(II) R128(0): PLL parameters: rf=2950 rd=65 min=12500 max=35000; xclk=12000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module already built-in
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
        compiled for 1.3.0, module version = 1.1.0
        ABI class: X.Org Video Driver, version 1.2
(II) R128(0): VESA BIOS detected
(II) R128(0): VESA VBE Version 2.0


(II) R128(0): Max H-Image Size [cm]: horiz.: 41  vert.: 31 ->
(II) R128(0): Gamma: 2.


(EE) R128(0): No DFP detected --> What is DFP? --> ?Problem?
(II) R128(0): SYNAPS, Composite, DPMS: Using hsync range of 31.00-79.00 kHz
(II) R128(0): SYNAPS, Composite, DPMS: Using vrefresh range of 59.00-75.00 Hz
(II) R128(0): Clock range:  12.50 to 350.00 MHz


Setting up tile and stipple cache:
                32 128x128 slots
                19 256x256 slots
(II) R128(0): Acceleration enabled
(==) R128(0): Backing store disabled
(==) R128(0): Silken mouse enabled
(II) R128(0): Using hardware cursor (scanline 14412)
(II) R128(0): Largest offscreen area available: 1600 x 1198->? Problem 1600x1200
(II) R128(0): X context handle = 0x1
(II) R128(0): [drm] installed DRM signal handler
(II) R128(0): [DRI] installation complete
(II) R128(0): [drm] Added 128 16384 byte vertex/indirect buffers
(II) R128(0): [drm] Mapped 128 vertex/indirect buffers
(II) R128(0): [drm] dma control initialized, using IRQ 11
(II) R128(0): Direct rendering enabled



drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(WW) AIGLX: 3D driver claims to not support visual 0x23
(WW) AIGLX: 3D driver claims to not support visual 0x24
(WW) AIGLX: 3D driver claims to not support visual 0x25
(WW) AIGLX: 3D driver claims to not support visual 0x26
(WW) AIGLX: 3D driver claims to not support visual 0x27
(WW) AIGLX: 3D driver claims to not support visual 0x28
(WW) AIGLX: 3D driver claims to not support visual 0x29
(WW) AIGLX: 3D driver claims to not support visual 0x2a
(WW) AIGLX: 3D driver claims to not support visual 0x2b
(WW) AIGLX: 3D driver claims to not support visual 0x2c
(WW) AIGLX: 3D driver claims to not support visual 0x2d
(WW) AIGLX: 3D driver claims to not support visual 0x2e
(WW) AIGLX: 3D driver claims to not support visual 0x2f
(WW) AIGLX: 3D driver claims to not support visual 0x30
(WW) AIGLX: 3D driver claims to not support visual 0x31
(WW) AIGLX: 3D driver claims to not support visual 0x32
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r128_dri.so
(II) GLX: Initialized DRI GL provider for screen 0



All times are GMT -5. The time now is 11:40 PM.