LinuxQuestions.org - Slackware Atheros AR5007 configuration(?) problem and Wifi issues

I think I've finally reached the point where I've exhausted all of my options. I'm running a Compaq A945US laptop with Slackware 12.1 (KDE 3.5), and I'm having some serious issues with my wireless. I finally dug up some information on the card (why does everyone insist on keeping it a secret?) and it's an Atheros AR5007 (or at least according to the very general specifics at HP.com). The lspci shows it as an Atheros AR242x chipset, which narrowed it down to the AR5006EGS or the AR5007. So I hope the AR5007 model is right. Anyway, I've been installing and modprobing like crazy to try and get this thing to work and I think I might have finally gotten it close to a working point. Hopefully someone can tell me where I need to fix something or if I'm completely off track. I've tried both ndiswrapper and madwifi, the lastest madwifi snapshot seems to have the best support and it modprobes nicely (ath_pci), but as far as the wifi being detected, that's just about all that happens. I can use iwconfig to change things like the essid and whatnot, but I can't connect to my network. If someone could help me out with this, I would really appreciate it. Here's my iwconfig and lspci -v.

Code:

root@Yrahcaz:~# iwconfig

lo        no wireless extensions.



eth0      no wireless extensions.



wifi0    no wireless extensions.



ath0      IEEE 802.11g  ESSID:"tesnet"  Nickname:"Yrahcaz"

          Mode:Managed  Frequency:2.437 GHz  Access Point: 00:1D:7E:56:C3:85

          Bit Rate=54 Mb/s  Tx-Power=16 dBm  Sensitivity=1/1

          Retry:off  RTS thr:off  Fragment thr:off

          Encryption key:off

          Power Management:off

          Link Quality=0/70  Signal level=-96 dBm  Noise level=-96 dBm

          Rx invalid nwid:1018  Rx invalid crypt:0  Rx invalid frag:0

          Tx excessive retries:0  Invalid misc:0  Missed beacon:0

Code:

root@Yrahcaz:~# lspci -v

00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, fast devsel, latency 0

        Capabilities: [e0] Vendor Specific Information <?>

        Kernel driver in use: agpgart-intel

        Kernel modules: intel-agp



00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, fast devsel, latency 0, IRQ 16

        Memory at d1000000 (64-bit, non-prefetchable) [size=1M]

        Memory at c0000000 (64-bit, prefetchable) [size=256M]

        I/O ports at 30d0 [size=8]

        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-

        Capabilities: [d0] Power Management version 3

        Kernel modules: intelfb



00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, fast devsel, latency 0

        Memory at d1100000 (64-bit, non-prefetchable) [size=1M]

        Capabilities: [d0] Power Management version 3



00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)

        Subsystem: Conexant Unknown device 5051

        Flags: bus master, fast devsel, latency 0, IRQ 22

        Memory at d2400000 (64-bit, non-prefetchable) [size=16K]

        Capabilities: [50] Power Management version 2

        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

        Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [130] Root Complex Link <?>

        Kernel driver in use: HDA Intel

        Kernel modules: snd-hda-intel



00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0

        I/O behind bridge: 00002000-00002fff

        Memory behind bridge: d1300000-d23fffff

        Prefetchable memory behind bridge: 00000000d0000000-00000000d0ffffff

        Capabilities: [40] Express Root Port (Slot+), MSI 00

        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-

        Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device 30d9

        Capabilities: [a0] Power Management version 2

        Capabilities: [100] Virtual Channel <?>

        Capabilities: [180] Root Complex Link <?>

        Kernel driver in use: pcieport-driver

        Kernel modules: shpchp



00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0, IRQ 21

        I/O ports at 3080 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0, IRQ 20

        I/O ports at 3060 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0, IRQ 19

        I/O ports at 3040 [size=32]

        Kernel driver in use: uhci_hcd

        Kernel modules: uhci-hcd



00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0, IRQ 23

        Memory at d2404800 (32-bit, non-prefetchable) [size=1K]

        Capabilities: [50] Power Management version 2

        Capabilities: [58] Debug port: BAR=1 offset=00a0

        Kernel driver in use: ehci_hcd

        Kernel modules: ehci-hcd



00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) (prog-if 01 [Subtractive decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=32

        I/O behind bridge: 00001000-00001fff

        Memory behind bridge: d1200000-d12fffff

        Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device 30d9



00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0

        Capabilities: [e0] Vendor Specific Information <?>

        Kernel modules: iTCO_wdt



00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 0, IRQ 19

        I/O ports at 01f0 [size=8]

        I/O ports at 03f4 [size=1]

        I/O ports at 0170 [size=8]

        I/O ports at 0374 [size=1]

        I/O ports at 30a0 [size=16]

        Kernel driver in use: PIIX_IDE



00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17

        I/O ports at 30b8 [size=8]

        I/O ports at 30dc [size=4]

        I/O ports at 30b0 [size=8]

        I/O ports at 30d8 [size=4]

        I/O ports at 3020 [size=32]

        Memory at d2404000 (32-bit, non-prefetchable) [size=2K]

        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/2 Enable-

        Capabilities: [70] Power Management version 3

        Capabilities: [a8] SATA HBA <?>

        Kernel driver in use: ahci



00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)





        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: medium devsel, IRQ 19

        Memory at d2404c00 (32-bit, non-prefetchable) [size=256]

        I/O ports at 3000 [size=32]

        Kernel driver in use: i801_smbus

        Kernel modules: i2c-i801



01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)

        Subsystem: Hewlett-Packard Company Unknown device 137a

        Flags: bus master, fast devsel, latency 0, IRQ 16

        Memory at d1300000 (64-bit, non-prefetchable) [size=64K]

        Capabilities: [40] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-

        Capabilities: [60] Express Legacy Endpoint, MSI 00

        Capabilities: [90] MSI-X: Enable- Mask- TabSize=1

        Capabilities: [100] Advanced Error Reporting <?>

        Capabilities: [140] Virtual Channel <?>

        Kernel driver in use: ath_pci

        Kernel modules: ath5k, ath_pci



02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

        Subsystem: Hewlett-Packard Company Unknown device 30d9

        Flags: bus master, medium devsel, latency 64, IRQ 16

        I/O ports at 1000 [size=256]

        Memory at d1200000 (32-bit, non-prefetchable) [size=256]

        Capabilities: [50] Power Management version 2

        Kernel driver in use: 8139too

        Kernel modules: 8139too, 8139cp

I can post just about anything else you need. Thanks!

Code:

root@Yrahcaz:~# dmesg

Linux version 2.6.26.3-smp (root@Yrahcaz) (gcc version 4.2.3) #4 SMP PREEMPT Sat Aug 23 18:56:32 MDT 2008

BIOS-provided physical RAM map:

 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)

 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)

 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)

 BIOS-e820: 0000000000100000 - 00000000bf4d2000 (usable)

 BIOS-e820: 00000000bf4d2000 - 00000000bf4dd000 (reserved)

 BIOS-e820: 00000000bf4dd000 - 00000000bf534000 (usable)

 BIOS-e820: 00000000bf534000 - 00000000bf537000 (reserved)

 BIOS-e820: 00000000bf537000 - 00000000bf5bb000 (usable)

 BIOS-e820: 00000000bf5bb000 - 00000000bf5bf000 (reserved)

 BIOS-e820: 00000000bf5bf000 - 00000000bf678000 (usable)

 BIOS-e820: 00000000bf678000 - 00000000bf6bf000 (ACPI NVS)

 BIOS-e820: 00000000bf6bf000 - 00000000bf700000 (ACPI data)

 BIOS-e820: 00000000bf700000 - 00000000c0000000 (reserved)

 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)

 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)

 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)

 BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)

 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)

 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)

2166MB HIGHMEM available.

896MB LOWMEM available.

found SMP MP-table at [c00fe270] 000fe270

Entering add_active_range(0, 0, 783992) 0 entries of 256 used

Zone PFN ranges:

  DMA            0 ->    4096

  Normal      4096 ->  229376

  HighMem    229376 ->  783992

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0:        0 ->  783992

On node 0 totalpages: 783992

  DMA zone: 32 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 4064 pages, LIFO batch:0

  Normal zone: 1760 pages used for memmap

  Normal zone: 223520 pages, LIFO batch:31

  HighMem zone: 4333 pages used for memmap

  HighMem zone: 550283 pages, LIFO batch:31

  Movable zone: 0 pages used for memmap

DMI 2.4 present.

ACPI: RSDP 000FE020, 0024 (r2 HP    )

ACPI: XSDT BF6FE120, 0064 (r1 HPQOEM SLIC-MPC        1      1000013)

ACPI: FACP BF6FD000, 00F4 (r4 HP    SPARTAN        1 LOHR        0)

ACPI: DSDT BF6F4000, 802F (r1 HP    SPARTAN        1 LOHR        0)

ACPI: FACS BF67D000, 0040

ACPI: APIC BF6F3000, 0068 (r2 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: HPET BF6F2000, 0038 (r1 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: MCFG BF6F1000, 003C (r1 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: ASF! BF6F0000, 00A5 (r32 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: SLIC BF6EF000, 0176 (r1 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: BOOT BF6EE000, 0028 (r1 HPQOEM SLIC-MPC        1 LOHR        0)

ACPI: SSDT BF6ED000, 04C4 (r1  PmRef    CpuPm    3000 INTL 20051117)

ACPI: DMI detected: Hewlett-Packard

ACPI: PM-Timer IO Port: 0x408

ACPI: Local APIC address 0xfee00000

ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)

ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)

ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])

ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])

ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])

IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23

ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

ACPI: IRQ0 used by override.

ACPI: IRQ2 used by override.

ACPI: IRQ9 used by override.

Enabling APIC mode:  Flat.  Using 1 I/O APICs

ACPI: HPET id: 0x8086a201 base: 0xfed00000

Using ACPI (MADT) for SMP configuration information

Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)

PM: Registered nosave memory: 000000000009f000 - 00000000000a0000

PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000

PM: Registered nosave memory: 00000000000e0000 - 0000000000100000

SMP: Allowing 2 CPUs, 0 hotplug CPUs

PERCPU: Allocating 39336 bytes of per cpu data

NR_CPUS: 32, nr_cpu_ids: 2

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 777867

Kernel command line: BOOT_IMAGE=Linux ro root=802 vt.default_utf8=0

mapped APIC to ffffb000 (fee00000)

mapped IOAPIC to ffffa000 (fec00000)

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Initializing CPU#0

PID hash table entries: 4096 (order: 12, 16384 bytes)

Detected 1862.025 MHz processor.

Console: colour dummy device 80x25

console [tty0] enabled

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 3104668k/3135968k available (2926k kernel code, 30160k reserved, 1157k data, 292k init, 2218392k highmem)

virtual kernel memory layout:

    fixmap  : 0xffe15000 - 0xfffff000  (1960 kB)

    pkmap  : 0xff800000 - 0xffc00000  (4096 kB)

    vmalloc : 0xf8800000 - 0xff7fe000  ( 111 MB)

    lowmem  : 0xc0000000 - 0xf8000000  ( 896 MB)

      .init : 0xc0504000 - 0xc054d000  ( 292 kB)

      .data : 0xc03dba03 - 0xc04fd120  (1157 kB)

      .text : 0xc0100000 - 0xc03dba03  (2926 kB)

Checking if this processor honours the WP bit even in supervisor mode...Ok.

CPA: page pool initialized 1 of 1 pages preallocated

SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

hpet clockevent registered

Calibrating delay using timer specific routine.. 3728.51 BogoMIPS (lpj=7457024)

Security Framework initialized

Capability LSM initialized

Mount-cache hash table entries: 512

CPU: L1 I cache: 32K, L1 D cache: 32K

CPU: L2 cache: 1024K

CPU: Physical Processor ID: 0

CPU: Processor Core ID: 0

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

using mwait in idle threads.

Checking 'hlt' instruction... OK.

ACPI: Core revision 20080321

ENABLING IO-APIC IRQs

..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1

CPU0: Intel(R) Pentium(R) Dual  CPU  T2390  @ 1.86GHz stepping 0d

Booting processor 1/1 ip 6000

Initializing CPU#1

Calibrating delay using timer specific routine.. 3723.95 BogoMIPS (lpj=7447909)

CPU: L1 I cache: 32K, L1 D cache: 32K

CPU: L2 cache: 1024K

CPU: Physical Processor ID: 0

CPU: Processor Core ID: 1

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#1.

CPU1: Intel(R) Pentium(R) Dual  CPU  T2390  @ 1.86GHz stepping 0d

checking TSC synchronization [CPU#0 -> CPU#1]: passed.

Brought up 2 CPUs

Total of 2 processors activated (7452.46 BogoMIPS).

net_namespace: 644 bytes

xor: automatically using best checksumming function: pIII_sse

  pIII_sse  :  6792.000 MB/sec

xor: using function: pIII_sse (6792.000 MB/sec)

NET: Registered protocol family 16

No dock devices found.

ACPI: bus type pci registered

PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255

PCI: MCFG area at e0000000 reserved in E820

PCI: Using MMCONFIG for extended config space

PCI: Using configuration type 1 for base access

Setting up standard PCI resources

ACPI: EC: Look up EC in DSDT

ACPI: BIOS _OSI(Linux) query ignored via DMI

ACPI: Interpreter enabled

ACPI: (supports S0 S3 S4 S5)

ACPI: Using IOAPIC for interrupt routing

ACPI: EC: non-query interrupt received, switching to interrupt mode

ACPI: EC: GPE storm detected, disabling EC GPE

ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62

ACPI: EC: driver started in poll mode

ACPI: PCI Root Bridge [PCI0] (0000:00)

pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO

pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO

PCI: Transparent bridge - 0000:00:1e.0

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]

ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)

ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)

ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)

Linux Plug and Play Support v0.97 (c) Adam Belay

pnp: PnP ACPI init

ACPI: bus type pnp registered

pnp: PnP ACPI: found 9 devices

ACPI: ACPI bus type pnp unregistered

SCSI subsystem initialized

libata version 3.00 loaded.

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

PCI: Using ACPI for IRQ routing

ACPI: RTC can wake from S4

system 00:01: ioport range 0x164e-0x164f has been reserved

system 00:01: ioport range 0x600-0x60f has been reserved

system 00:01: ioport range 0x610-0x610 has been reserved

system 00:01: ioport range 0x800-0x80f has been reserved

system 00:01: ioport range 0x810-0x817 has been reserved

system 00:01: ioport range 0x400-0x47f has been reserved

system 00:01: ioport range 0x500-0x53f has been reserved

system 00:01: ioport range 0xff2c-0xff2f has been reserved

system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved

system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved

system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved

system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved

system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved

system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved

system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved

PCI: Bridge: 0000:00:1c.0

  IO window: 2000-2fff

  MEM window: 0xd1300000-0xd23fffff

  PREFETCH window: 0x00000000d0000000-0x00000000d0ffffff

PCI: Bridge: 0000:00:1e.0

  IO window: 1000-1fff

  MEM window: 0xd1200000-0xd12fffff

  PREFETCH window: disabled.

ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 18 (level, low) -> IRQ 18

PCI: Setting latency timer of device 0000:00:1c.0 to 64

PCI: Setting latency timer of device 0000:00:1e.0 to 64

NET: Registered protocol family 2

IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

TCP bind hash table entries: 65536 (order: 7, 524288 bytes)

TCP: Hash tables configured (established 131072 bind 65536)

TCP reno registered

NET: Registered protocol family 1

Simple Boot Flag value 0x5 read from CMOS RAM was invalid

Simple Boot Flag at 0x44 set to 0x1

highmem bounce pool size: 64 pages

msgmni has been set to 1732

async_tx: api initialized (async)

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

pci 0000:00:02.0: Boot video device

PCI: Setting latency timer of device 0000:00:1c.0 to 64

assign_interrupt_mode Found MSI capability

Allocate Port Service[0000:00:1c.0:pcie00]

Allocate Port Service[0000:00:1c.0:pcie02]

Allocate Port Service[0000:00:1c.0:pcie03]

vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 3072k, total 7616k

vesafb: mode is 1024x768x16, linelength=2048, pages=3

vesafb: scrolling: redraw

vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0

Console: switching to colour frame buffer device 128x48

fb0: VESA VGA frame buffer device

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

floppy0: no floppy controllers found

brd: module loaded

loop: module loaded

input: Macintosh mouse button emulation as /class/input/input0

Uniform Multi-Platform E-IDE driver

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at  PCI slot 0000:00:1f.1

ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level, low) -> IRQ 19

ICH8M: not 100% native mode: will probe irqs later

    ide0: BM-DMA at 0x30a0-0x30a7

    ide1: BM-DMA at 0x30a8-0x30af

Probing IDE interface ide0...

hda: Optiarc DVD RW AD-7561A, ATAPI CD/DVD-ROM drive

hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4

hda: MWDMA2 mode selected

Probing IDE interface ide1...

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

ide1 at 0x170-0x177,0x376 on irq 15

ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports

ide_generic: I/O resource 0x1F0-0x1F7 not free.

ide_generic: I/O resource 0x170-0x177 not free.

hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache

Uniform CD-ROM driver Revision: 3.20

ide-floppy driver 1.00

Driver 'sd' needs updating - please use bus_type methods

Driver 'sr' needs updating - please use bus_type methods

ahci 0000:00:1f.2: version 3.0

ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 17 (level, low) -> IRQ 17

ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode

ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part

PCI: Setting latency timer of device 0000:00:1f.2 to 64

scsi0 : ahci

scsi1 : ahci

scsi2 : ahci

ata1: SATA max UDMA/133 abar m2048@0xd2404000 port 0xd2404100 irq 17

ata2: DUMMY

ata3: DUMMY

ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out

ata1.00: ATA-7: WDC WD1600BEVS-60RST0, 04.01G04, max UDMA/100

ata1.00: 312581808 sectors, multi 16: LBA48

ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out

ata1.00: configured for UDMA/100

scsi 0:0:0:0: Direct-Access    ATA      WDC WD1600BEVS-6 04.0 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

 sda: sda1 sda2

sd 0:0:0:0: [sda] Attached SCSI disk

usbmon: debugfs is not available

PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MSE0] at 0x60,0x64 irq 1,12

serio: i8042 KBD port at 0x60,0x64 irq 1

serio: i8042 AUX port at 0x60,0x64 irq 12

mice: PS/2 mouse device common for all mice

md: linear personality registered for level -1

md: raid0 personality registered for level 0

md: raid1 personality registered for level 1

md: raid10 personality registered for level 10

input: AT Translated Set 2 keyboard as /class/input/input1

raid6: int32x1    725 MB/s

raid6: int32x2    743 MB/s

raid6: int32x4    580 MB/s

raid6: int32x8    522 MB/s

raid6: mmxx1    2370 MB/s

raid6: mmxx2    2781 MB/s

raid6: sse1x1    1495 MB/s

raid6: sse1x2    1994 MB/s

raid6: sse2x1    2838 MB/s

raid6: sse2x2    3278 MB/s

raid6: using algorithm sse2x2 (3278 MB/s)

md: raid6 personality registered for level 6

md: raid5 personality registered for level 5

md: raid4 personality registered for level 4

md: multipath personality registered for level -4

device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com

cpuidle: using governor ladder

TCP cubic registered

Initializing XFRM netlink socket

NET: Registered protocol family 17

Starting balanced_irq

Using IPI No-Shortcut mode

md: Autodetecting RAID arrays.

md: Scanned 0 and added 0 devices.

md: autorun ...

md: ... autorun DONE.

kjournald starting.  Commit interval 5 seconds

EXT3-fs: mounted filesystem with ordered data mode.

VFS: Mounted root (ext3 filesystem) readonly.

Freeing unused kernel memory: 292k freed

sd 0:0:0:0: Attached scsi generic sg0 type 0

Linux agpgart interface v0.103

agpgart: Detected an Intel 965GM Chipset.

agpgart: Detected 7676K stolen memory.

agpgart: AGP aperture is 256M @ 0xc0000000

ACPI: SSDT BF67CC10, 026E (r1  PmRef  Cpu0Ist    3000 INTL 20051117)

ACPI: SSDT BF67B610, 05D7 (r1  PmRef  Cpu0Cst    3001 INTL 20051117)

Monitor-Mwait will be used to enter C-1 state

Monitor-Mwait will be used to enter C-2 state

Monitor-Mwait will be used to enter C-3 state

ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])

ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22

PCI: Setting latency timer of device 0000:00:1b.0 to 64

ACPI: ACPI0007:00 is registered as cooling_device0

ACPI: Processor [CPU0] (supports 8 throttling states)

input: Power Button (FF) as /class/input/input2

ACPI: Power Button (FF) [PWRF]

ACPI: SSDT BF67CF10, 00C4 (r1  PmRef  Cpu1Ist    3000 INTL 20051117)

ACPI: SSDT BF67ED10, 0083 (r1  PmRef  Cpu1Cst    3000 INTL 20051117)

ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])

ACPI: ACPI0007:01 is registered as cooling_device1

ACPI: Processor [CPU1] (supports 8 throttling states)

input: Power Button (CM) as /class/input/input3

ACPI: Power Button (CM) [PWRB]

input: Lid Switch as /class/input/input4

ACPI: Lid Switch [LID0]

input: Sleep Button (CM) as /class/input/input5

ACPI: Sleep Button (CM) [SLPB]

USB Universal Host Controller Interface driver v3.0

ACPI: PCI Interrupt 0000:00:1d.0[D] -> GSI 21 (level, low) -> IRQ 21

PCI: Setting latency timer of device 0000:00:1d.0 to 64

uhci_hcd 0000:00:1d.0: UHCI Host Controller

uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1

uhci_hcd 0000:00:1d.0: irq 21, io base 0x00003080

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

iTCO_vendor_support: vendor-support=0

8139too Fast Ethernet driver 0.9.28

iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)

iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x0460)

iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)

ACPI: AC Adapter [AC] (on-line)

ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23

PCI: Setting latency timer of device 0000:00:1d.7 to 64

ehci_hcd 0000:00:1d.7: EHCI Host Controller

ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2

ehci_hcd 0000:00:1d.7: debug port 1

PCI: cache line size of 32 is not supported by device 0000:00:1d.7

ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2404800

ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 6 ports detected

Marking TSC unstable due to: TSC halts in idle.

rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0

rtc0: alarms up to one month

ACPI: Battery Slot [BAT0] (battery present)

ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 20

PCI: Setting latency timer of device 0000:00:1d.1 to 64

uhci_hcd 0000:00:1d.1: UHCI Host Controller

uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3

uhci_hcd 0000:00:1d.1: irq 20, io base 0x00003060

usb usb3: configuration #1 chosen from 1 choice

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 19 (level, low) -> IRQ 19

PCI: Setting latency timer of device 0000:00:1d.2 to 64

uhci_hcd 0000:00:1d.2: UHCI Host Controller

uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4

uhci_hcd 0000:00:1d.2: irq 19, io base 0x00003040

usb usb4: configuration #1 chosen from 1 choice

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 2 ports detected

input: Video Bus as /class/input/input6

ACPI: Video Device [OVGA] (multi-head: yes  rom: no  post: no)

ACPI: PCI Interrupt 0000:00:1f.3[D] -> GSI 19 (level, low) -> IRQ 19

ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 16 (level, low) -> IRQ 16

PCI: Setting latency timer of device 0000:02:01.0 to 64

eth0: RealTek RTL8139 at 0x1000, 00:1e:ec:76:88:4a, IRQ 16

eth0:  Identified 8139 chip type 'RTL-8100B/8139D'

ACPI: LNXTHERM:01 is registered as thermal_zone0

ACPI: Thermal Zone [TZ01] (55 C)

usb 2-5: new high speed USB device using ehci_hcd and address 3

input: PS/2 Generic Mouse as /class/input/input7

fuse init (API version 7.9)

usb 2-5: configuration #1 chosen from 1 choice

Initializing USB Mass Storage driver...

usb 2-6: new high speed USB device using ehci_hcd and address 4

usb 2-6: configuration #1 chosen from 1 choice

scsi3 : SCSI emulation for USB Mass Storage devices

usb-storage: device found at 3

usb-storage: waiting for device to settle before scanning

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usb 1-2: new low speed USB device using uhci_hcd and address 2

Clocksource tsc unstable (delta = -69684287 ns)

usb 1-2: configuration #1 chosen from 1 choice

EXT3 FS on sda2, internal journal

usbcore: registered new interface driver hiddev

input: Logitech USB Receiver as /class/input/input8

input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2

input: Logitech USB Receiver as /class/input/input9

input,hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-2

usbcore: registered new interface driver usbhid

usbhid: v2.6:USB HID core driver

lp: driver loaded but no devices found

scsi 3:0:0:0: Direct-Access    Generic- Multi-Card      1.00 PQ: 0 ANSI: 0 CCS

sd 3:0:0:0: [sdb] Attached SCSI removable disk

sd 3:0:0:0: Attached scsi generic sg1 type 0

usb-storage: device scan complete

Intel ISA PCIC probe: not found.

Databook TCIC-2 PCMCIA probe: not found.

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

NET: Registered protocol family 10

lo: Disabled Privacy Extensions

eth0: no IPv6 routers present

[drm] Initialized drm 1.1.0 20060810

ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16

PCI: Setting latency timer of device 0000:00:02.0 to 64

[drm] Initialized i915 1.6.0 20060119 on minor 0

ath_hal: module license 'Proprietary' taints kernel.

AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417)

ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16

PCI: Setting latency timer of device 0000:01:00.0 to 64

MadWifi: ath_attach: Switching rfkill capability off.

wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, Radio 10.2)

ath_pci: wifi0: Atheros 5424/2424: mem=0xd1300000, irq=16

ath0: no IPv6 routers present

ath0: no IPv6 routers present

eth0: link down

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

eth0: no IPv6 routers present

ath0: no IPv6 routers present