I have some problem getting my intel 2100 3B wireless to work. It seem that it manage to associate with the Access Point but unable to send data. Anyone know what are the possible reasons.

ieee80211_crypt: registered algorithm 'NULL'
ieee80211: loading with WEP enabled.
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 0.50
ipw2100: Copyright(c) 2003-2004 Intel Corporation
ipw2100: Compiled with LEGACY FW load.
Detected ipw2100 PCI device at 0000:01:02.0, mem: 0xE0000000-0xE0000FFF -> 21cb0
000, irq: 10
divert: allocating divert_blk for eth1
eth1: Using legacy firmware load.
Registered as eth1
ipw2100: eth1: Restarting adapter.
eth1: Using legacy firmware load.
ieee80211_crypt: registered algorithm 'WEP'
Setting security to 1
eth1: no IPv6 routers present

eth1: Associated with 'linky' at 11Mbps, channel 8

eth1: Non consumed packet:
00000000 08 42 9F 00 00 04 23 5F 8A 62 00 0C 41 35 37 D7 .B....#_ .b..A57.
00000010 00 0C 41 35 37 D7 70 AF 00 3E 3E 40 97 36 8C 54 ..A57.p. .>>@.6.T
00000020 82 A6 0B 2B 40 B6 4A 07 FF 83 49 F3 44 EB 69 96 ...+@.J. ..I.D.i.
00000030 0C BB 7D DE A6 CD 61 1B 6C 80 49 8E 0D 97 FB BB ..}...a. l.I.....
00000040 6A B3 AC 32 j..2

eth1: Non consumed packet:
00000000 08 42 9F 00 00 04 23 5F 8A 62 00 0C 41 35 37 D7 .B....#_ .b..A57.
00000010 00 0C 41 35 37 D7 70 AF 00 3E 3E 40 97 36 8C 54 ..A57.p. .>>@.6.T
00000020 82 A6 0B 2B 40 B6 4A 07 FF 83 49 F3 44 EB 69 96 ...+@.J. ..I.D.i.
00000030 0C BB 7D DE A6 CD 61 1B 6C 80 49 8E 0D 97 FB BB ..}...a. l.I.....
00000040 6A B3 AC 32 j..2

anyone know what this non consumed packet is

[root@cauthon sbin]# ./iwconfig
lo no wireless extensions.

sit0 no wireless extensions.

eth0 no wireless extensions.

eth1 IEEE 802.11b ESSID:"linky" Nickname:"cauthon"
Mode:Managed Channel:8 Access Point: 00:0C:41:35:37:D7
Bit Rate=11Mb/s Tx-Power=32 dBm
Retry:on RTS thr=2304 B Fragment thr:off
Encryption key:EBFE-CD7F-82B3-BD34-91CE-EAA1-22 Security mode:restricted
Power Management:off
Link Quality:87/100 Signal level:-71 dBm Noise level:-98 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:2

seem that it is associated with the Access Point


[root@cauthon cauthon]# /sbin/ifconfig
eth1 Link encap:Ethernet HWaddr 00:04:23:5F:8A:62
inet addr:192.168.100.98 Bcast:192.168.100.255 Mask:255.255.255.0
inet6 addr: fe80::204:23ff:fe5f:8a62/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:156 dropped:156 overruns:0 frame:0
TX packets:152 errors:0 dropped:0 overruns:0 carrier:1
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:5640 (5.5 Kb)
Interrupt:10 Memory:e0000000-e0000fff

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2788 errors:0 dropped:0 overruns:0 frame:0
TX packets:2788 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3355927 (3.2 Mb) TX bytes:3355927 (3.2 Mb)

a high error and drop rate but i just can't figure what are the reasons.:(