LinuxQuestions.org
Visit the LQ Articles and Editorials section
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking > Linux - Wireless Networking
User Name
Password
Linux - Wireless Networking This forum is for the discussion of wireless networking in Linux.

Notices

Reply
 
Search this Thread
Old 08-26-2007, 11:40 PM   #1
Setya
Member
 
Registered: Apr 2007
Posts: 41

Rep: Reputation: 15
eth0 is detected as wireless instead of ethernet


Hi all,

On my laptop F7 detects eth0 as wireless instead of ethernet, while eth1 is detected ethernet instead of wireless and each time I want to connect to network it always tell me to check cable.

Please help to fix this.

Thanks in advanced.

Any help would be greatly appreciated.

Best Regards,

Setya
 
Old 08-27-2007, 01:53 AM   #2
The_Outlander
Member
 
Registered: Aug 2004
Location: Australia
Distribution: Slackware 12.1
Posts: 235

Rep: Reputation: 30
The wireless module is possibly loading before the cable interface. Wireless becomes eth0 and cable eth1.
Don't know which distro you're using, but if you want eth0 to become your cable connection that module needs to load first, the wireless module will then follow.
 
Old 08-27-2007, 08:47 AM   #3
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Hi,

Quote:
Originally Posted by The_Outlander View Post
The wireless module is possibly loading before the cable interface. Wireless becomes eth0 and cable eth1.
Don't know which distro you're using, but if you want eth0 to become your cable connection that module needs to load first, the wireless module will then follow.
Thank you for your response.

My distro is Fedora 7.

How can I make the ethernet module load first ?

Regards,

Setya
 
Old 08-27-2007, 08:54 AM   #4
rossonieri#1
Member
 
Registered: Jun 2007
Posts: 359

Rep: Reputation: 34
hi,

you can try not activating eth0 on boot,
or
modify your ifcfg-ethx accordingly - too risky thou.

cheers.
 
Old 08-29-2007, 08:07 AM   #5
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Quote:
Originally Posted by rossonieri#1 View Post

you can try not activating eth0 on boot,
How to do this ?

Quote:
modify your ifcfg-ethx accordingly - too risky thou.
I can't find ifcfg-eth* anywhere, only ifcfg-lo.



BTW here's the results of various commands.

Code:
[root@PromisedLand /]# more /etc/modprobe.conf
alias scsi_hostadapter ata_piix
alias scsi_hostadapter1 usb-storage
alias snd-card-0 snd-intel8x0
options snd-card-0 index=0
options snd-intel8x0 index=0
alias eth0 bcm5700
Code:
kudzu -p:

...
class: NETWORK
bus: PCI
detached: 0
device: eth0
driver: ipw2200
desc: "Intel Corporation PRO/Wireless 2200BG Network Connection"
network.hwaddr: 00:12:f0:6d:03:05
vendorId: 8086
deviceId: 4220
subVendorId: 103c
subDeviceId: 12f6
pciType: 1
pcidom:    0
pcibus:  2
pcidev:  4
pcifn:  0
-
class: NETWORK
bus: PCI
detached: 0
device: eth1
driver: tg3
desc: "Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet"
network.hwaddr: 00:14:c2:e4:83:06
vendorId: 14e4
deviceId: 165d
subVendorId: 14e4
subDeviceId: 165d
pciType: 1
pcidom:    0
pcibus:  2
pcidev:  e
pcifn:  0
...
Code:
[root@PromisedLand src]# dmesg | grep -i eth0
bridge-eth0: peer interface eth0 not found, will wait for it to come up
bridge-eth0: attached
ADDRCONF(NETDEV_UP): eth0: link is not ready
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: disabling the bridge
bridge-eth0: down
Code:
[root@PromisedLand src]# dmesg | grep -i eth1
eth1: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth1: Broadcom BCM5705 Integrated Copper transceiver found
eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth1: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth1: Broadcom BCM5705 Integrated Copper transceiver found
eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth1: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth1: Broadcom BCM5705 Integrated Copper transceiver found
eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth1: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth1: Broadcom BCM5705 Integrated Copper transceiver found
eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON

Any help would be greatly appreciated.

Best Regards,

Setya
 
Old 08-29-2007, 10:05 AM   #6
rossonieri#1
Member
 
Registered: Jun 2007
Posts: 359

Rep: Reputation: 34
Quote:
Originally Posted by Setya View Post
How to do this ?



I can't find ifcfg-eth* anywhere, only ifcfg-lo.

if you cant find it under /etc/sysconfig/network-script then there is something wrong with the installation,
since your output said there is a broadcom NIC as eth1.

try ifconfig -a --> to show all networking device.

HTH.
 
Old 08-30-2007, 04:55 AM   #7
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Hi,

Somehow, this morning when I boot, the eth0 & eth1 interface is correctly assigned and I can find ifcfg-eth0 in the directory you mentioned.
But I'm still unable to connect to the internet. It seems that kudzu keeps loading the wrong ethernet driver module. Instead of bcm5700 it loads tg3 which is problematic with the ethernet card in my laptop.


Please help.


Regards,

Setya
 
Old 08-31-2007, 07:12 AM   #8
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Well,

anybody ? anything ?

Setya
 
Old 08-31-2007, 12:56 PM   #9
soroccoheaven
Member
 
Registered: Jul 2007
Distribution: mandrake Mandriva Redhat CentOS Slackware
Posts: 221

Rep: Reputation: 30
will you pls post your ifconfig -a and lspci ?

as you said you now u r able to see both the enterfaces right ?
 
Old 09-03-2007, 01:04 AM   #10
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Hi,

Thanks for responding.

Quote:
Originally Posted by soroccoheaven View Post
will you pls post your ifconfig -a and lspci ?
Here are the results of some commands.

Code:
[root@PromisedLand /]# lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (re    v 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
02:04.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
02:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
02:06.1 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
02:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
02:06.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
02:06.4 Generic system peripheral [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital     Controller
02:06.5 Communication controller: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Smart Card Controller
02:0e.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet
Code:
[root@PromisedLand /]# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:14:C2:E4:83:06
          inet6 addr: fe80::214:c2ff:fee4:8306/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:33 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6984 (6.8 KiB)  TX bytes:6928 (6.7 KiB)
          Interrupt:16 Memory:d0020000-d0030000

eth1      Link encap:Ethernet  HWaddr 00:12:F0:6D:03:05
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:22 Base address:0x8000 Memory:d0000000-d0000fff

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7811 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7811 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:47494464 (45.2 MiB)  TX bytes:47494464 (45.2 MiB)

vmnet1    Link encap:Ethernet  HWaddr 00:50:56:C0:00:01
          inet addr:172.16.183.1  Bcast:172.16.183.255  Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:43 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

vmnet8    Link encap:Ethernet  HWaddr 00:50:56:C0:00:08
          inet addr:192.168.37.1  Bcast:192.168.37.255  Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:43 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
Code:
[root@PromisedLand /]# ifup eth0

Determining IP information for eth0... failed.
[root@PromisedLand /]#
Code:
[root@PromisedLand /]# dmesg | grep eth0
eth0: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth0: Broadcom BCM5705 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth0: Using PCI INTX interrupt
bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON
eth0: no IPv6 routers present
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
bcm5700: eth0 NIC Link is DOWN
bridge-eth0: disabling the bridge
bridge-eth0: down
ndiswrapper: changing interface name from 'wlan0' to 'eth0'
bridge-eth0: enabling the bridge
bridge-eth0: up
eth0: no IPv6 routers present
bridge-eth0: disabling the bridge
bridge-eth0: down
ndiswrapper: device eth0 removed
eth0: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth0: Broadcom BCM5705 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth0: Using PCI INTX interrupt
bridge-eth0: enabling the bridge
bridge-eth0: up
bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON
eth0: no IPv6 routers present
bcm5700: eth0 NIC Link is DOWN
bridge-eth0: disabling the bridge
bridge-eth0: down
ndiswrapper: changing interface name from 'wlan0' to 'eth0'
bridge-eth0: enabling the bridge
bridge-eth0: up
eth0: no IPv6 routers present
bridge-eth0: disabling the bridge
bridge-eth0: down
ndiswrapper: device eth0 removed
eth0: Broadcom BCM5705M 1000Base-T found at mem d0020000, IRQ 16, node addr 0014c2e48306
eth0: Broadcom BCM5705 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
eth0: Using PCI INTX interrupt
bridge-eth0: enabling the bridge
bridge-eth0: up
bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON
eth0: no IPv6 routers present
bcm5700: eth0 NIC Link is DOWN
bridge-eth0: disabling the bridge
bridge-eth0: down
eth0: Using PCI INTX interrupt
ADDRCONF(NETDEV_UP): eth0: link is not ready
bridge-eth0: enabling the bridge
bridge-eth0: up
bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
Quote:
as you said you now u r able to see both the enterfaces right ?
Yes, as printed by messages above I can see both interfaces fine.

Regards,

Setya
 
Old 09-03-2007, 02:03 AM   #11
soroccoheaven
Member
 
Registered: Jul 2007
Distribution: mandrake Mandriva Redhat CentOS Slackware
Posts: 221

Rep: Reputation: 30
eth0 Link encap:Ethernet HWaddr 00:14:C2:E4:83:06
inet6 addr: fe80::214:c2ff:fee4:8306/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:33 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6984 (6.8 KiB) TX bytes:6928 (6.7 KiB)
Interrupt:16 Memory:d0020000-d0030000

eth1 Link encap:Ethernet HWaddr 00:12:F0:6D:03:05
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x8000 Memory:d0000000-d0000fff



what about your IPv4 addresses ? (like inet addr. see the output for lo)
so configure you eth0 and shutdown the eth1 for now..let the problem be sorted for eth0 first you can make eth1 later ..so configure your eth0 and try to ping your gateway and post.
what are the pci slot positions for NIC and wifi NIC try to place nic in pci slot 1 and wifi in pci slot 2 if it is not like that.
 
Old 09-03-2007, 04:01 AM   #12
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Hi,

Quote:
Originally Posted by soroccoheaven View Post
what about your IPv4 addresses ? (like inet addr. see the output for lo)
so configure you eth0 and shutdown the eth1 for now..let the problem be sorted for eth0 first you can make eth1 later ..so configure your eth0 and try to ping your gateway and post.
what are the pci slot positions for NIC and wifi NIC try to place nic in pci slot 1 and wifi in pci slot 2 if it is not like that.
Sorry, I don't quite understand here.
Are you suggesting me to ?

1. ifdown eth1 ?
2. Try static IP instead of dynamic one ?

Do you see anything unusual with the data I posted ?

Regards,

Setya
 
Old 09-03-2007, 05:16 AM   #13
soroccoheaven
Member
 
Registered: Jul 2007
Distribution: mandrake Mandriva Redhat CentOS Slackware
Posts: 221

Rep: Reputation: 30
ya ..ifdown eth1 and give static ip to eth0

and what about your pci slot positioning ?..

Last edited by soroccoheaven; 09-03-2007 at 05:18 AM.
 
Old 09-03-2007, 07:04 AM   #14
Setya
Member
 
Registered: Apr 2007
Posts: 41

Original Poster
Rep: Reputation: 15
Hi,

Quote:
Originally Posted by soroccoheaven View Post
ya ..ifdown eth1 and give static ip to eth0
I have ifdown eth1 and use static IP, here's the result:
Code:
[root@PromisedLand setya]# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:14:C2:E4:83:06
          inet addr:192.168.0.107  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::214:c2ff:fee4:8306/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:194 errors:0 dropped:0 overruns:0 frame:0
          TX packets:218 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:17029 (16.6 KiB)  TX bytes:22608 (22.0 KiB)
          Interrupt:16 Memory:d0020000-d0030000

eth1      Link encap:Ethernet  HWaddr 00:12:F0:6D:03:05
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:23 Base address:0xe000 Memory:d0000000-d0000fff

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7989 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7989 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:47362212 (45.1 MiB)  TX bytes:47362212 (45.1 MiB)

vmnet1    Link encap:Ethernet  HWaddr 00:50:56:C0:00:01
          inet addr:172.16.183.1  Bcast:172.16.183.255  Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

vmnet8    Link encap:Ethernet  HWaddr 00:50:56:C0:00:08
          inet addr:192.168.37.1  Bcast:192.168.37.255  Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:45 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
Code:
[root@PromisedLand setya]# ping 192.168.0.1
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
From 192.168.0.107 icmp_seq=2 Destination Host Unreachable
From 192.168.0.107 icmp_seq=3 Destination Host Unreachable
From 192.168.0.107 icmp_seq=4 Destination Host Unreachable

--- 192.168.0.1 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3999ms
, pipe 3
Quote:
and what about your pci slot positioning ?..
You mean I have to change the position of pci slot in the laptop ?


Setya
 
Old 09-03-2007, 07:26 AM   #15
soroccoheaven
Member
 
Registered: Jul 2007
Distribution: mandrake Mandriva Redhat CentOS Slackware
Posts: 221

Rep: Reputation: 30
you arnt getting reply ..what is your default gateway ?..check and place right Default gateway
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
no eth0 (ethernet card not detected) beebop Linux - Networking 12 05-09-2007 09:51 AM
ethernet card SiS 900-Based PCI Fast Ethernet Adapter Not Detected pathan_azhar Linux - Networking 0 08-13-2006 04:15 AM
eth0 not detected as Ethernet, no internet for me :( sadseh Linux - Networking 2 01-02-2005 03:43 AM
Wireless network on eth1 diabled Ethernet eth0 and eth0 never comes back tadatoshi Linux - Wireless Networking 4 09-23-2004 05:57 PM
Ethernet Card detected in one kernel is not detected in the other?? ashishuttarwar Linux - Hardware 14 06-15-2004 10:06 PM


All times are GMT -5. The time now is 01:06 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration