LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Wireless Networking (http://www.linuxquestions.org/questions/linux-wireless-networking-41/)
-   -   Broadcom driver does not work (http://www.linuxquestions.org/questions/linux-wireless-networking-41/broadcom-driver-does-not-work-4175457157/)

sgmart 04-06-2013 03:47 PM

Broadcom driver does not work
 
I am attempting to enable my wireless interface in Slax Linux, so far, I know the driver I need is brcmsmac, since I have a broadcom card; and this work in Slackware.

The driver is available and does not show any errors when I load it with:

Code:

# modprobe brcmsmac
But no new interface is loaded.

Here is I've tried:

Code:

# lspci | grep Network

03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)

# ifconfig -a

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether e8:11:32:5f:ff:5e  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 41  base 0xc000 

lo: flags=8<LOOPBACK>  mtu 16436
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Any suggestion is greatly accepted!

frankbell 04-06-2013 08:31 PM

Start with some of the diagnostics in the beginning of this post and then post the output here, being sure to surround it with "code" tags, which become available when you click the "Go Advanced" button at the bottom of the "Quick Reply" window.

sgmart 03-08-2015 11:53 AM

Quote:

Originally Posted by sgmart (Post 4926482)
I am attempting to enable my wireless interface in Slax Linux, so far, I know the driver I need is brcmsmac, since I have a broadcom card; and this work in Slackware.

The driver is available and does not show any errors when I load it with:

Code:

# modprobe brcmsmac
But no new interface is loaded.

Here is I've tried:

Code:

# lspci | grep Network

03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)

# ifconfig -a

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether e8:11:32:5f:ff:5e  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 41  base 0xc000 

lo: flags=8<LOOPBACK>  mtu 16436
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Any suggestion is greatly accepted!

[SOLVED]
It issue was successfully answered at http://unix.stackexchange.com/questi...-does-not-work

Thanks a lot to slm!


All times are GMT -5. The time now is 05:25 PM.