Music without GUI

abakhiet · 04-25-2010, 02:02 AM

thanks my friend, but look in to your suggested command output

Quote:

[root@abakhiet ~]# lspci -vv
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 03)
Subsystem: Dell Optiplex GX240
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ff800000-ff9fffff
Prefetchable memory behind bridge: f8000000-fbffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ff600000-ff7fffff
Prefetchable memory behind bridge: 20000000-200fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 Controller (rev 12) (prog-if 80 [Master])
Subsystem: Dell Optiplex GX240
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]

00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus Controller (rev 12)
Subsystem: Dell Optiplex GX240
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 169
Region 4: I/O ports at ccd0 [size=16]

00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio Controller (rev 12)
Subsystem: Dell Unknown device 010e
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 169
Region 0: I/O ports at c800 [size=256]
Region 1: I/O ports at cc40 [size=64]

01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro Ultra TF (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Unknown device 0408
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 161
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at ec00 [size=256]
Region 2: Memory at ff8fc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at ff800000 [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Dell Optiplex GX240
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at dc80 [size=128]
Region 1: Memory at ff6ffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

Brains · 04-25-2010, 03:34 PM

Still not sure what Linux you're running?

A quick Google search using "Intel Corporation 82801BA/BAM AC'97 Audio Controller Linux" as keywords found a couple Ubuntu related problems with this audio controller. According to output of lspci -v command in one post showed the kernel module (driver) used is snd_intel8x0. It appears to work sporadically in Linux Ubuntu so far, could be permissions issues or mixer settings. One post of the two I looked at has the same machine: Dell Optiplex GX240.

abakhiet · 04-26-2010, 03:06 PM

Dear all, i need to tell you that finally i get some sound from MP3blaster when i get the volume up for PCM & PCM2 Mixers, but when i make a reboot for my Linux BOX, all of it returns to Zero.
So i need some way to make it stored in my configurations

Thanks in advance

Shadow_7 · 04-26-2010, 07:33 PM

alsactl store
alsactl restore

aumix (S - save / L - load)

Some distros don't load some settings if others are saved / present. Alsa normally takes priority IME.

/var/lib/alsa/asound.state

I'm not sure why that's not in /etc/ anymore? But debian had/has scripting in place that if that one exists, aumix save settings get skipped over at boot. And other quirks depending on what you use / how your system is setup.