LinuxQuestions.org
Latest LQ Deal: Complete CCNA, CCNP & Red Hat Certification Training Bundle
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Software
User Name
Password
Linux - Software This forum is for Software issues.
Having a problem installing a new program? Want to know which application is best for the job? Post your question in this forum.

Notices


Reply
  Search this Thread
Old 06-22-2002, 03:04 AM   #1
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Rep: Reputation: 30
Kernel unable to find the modules?


Hi All
I just recompiled my kernel and it works great. However, at boot time it complains about not finding specific modules.
During the compile process, I made sure to run the following wo commands (in order) to set up the modules, yet for some reason the kernel complains. here are the 2 commands I ran:

make modules
make modules_install

Note that due to this, three services failed to initialize, mainly

emu10k-snd-card
SuSE-Firewall
SuSE-Apache-Firewall

and I suspect the CDRecorder doesn't wrk because of "missing" modules

Can anyone help me figure this out?

Again, the kernel DOES boot, and lili is configured correctly
 
Old 06-22-2002, 03:47 AM   #2
acid_kewpie
Moderator
 
Registered: Jun 2001
Location: UK
Distribution: Gentoo, RHEL, Fedora, Centos
Posts: 43,417

Rep: Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974Reputation: 1974
well do they exist? did you select them properly when you chose the setup for the new kernel?
 
Old 06-22-2002, 03:52 AM   #3
MasterC
LQ Guru
 
Registered: Mar 2002
Location: Salt Lake City, UT - USA
Distribution: Gentoo ; LFS ; Kubuntu
Posts: 12,612

Rep: Reputation: 64
Or did you compile them into your kernel and they are still listed in modules.conf?

If so, go there and comment them out.
 
Old 06-22-2002, 06:52 AM   #4
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
well, I'm not sure what that All means. I did a make xconfig, selected the options, then nohupmake bzImage &
then macke clean then make dep
When all was done I did make modulesand makemodules_install.
So I don't know it SHOULD have installed the necessary modules shoudln't it?
 
Old 06-22-2002, 07:27 AM   #5
crashmeister
Senior Member
 
Registered: Feb 2002
Distribution: t2 - trying to anyway
Posts: 2,541

Rep: Reputation: 47
Did you copy the new system map to boot?
 
Old 06-22-2002, 07:51 AM   #6
MasterC
LQ Guru
 
Registered: Mar 2002
Location: Salt Lake City, UT - USA
Distribution: Gentoo ; LFS ; Kubuntu
Posts: 12,612

Rep: Reputation: 64
Well, yes it SHOULD have. But if you compiled your sound card into the kernel instead of as module, then it won't be module anymore. modules.conf would still have it listed and would still try to 'invoke' it at boot. So I guess the question is, did you compile them as mod's or directly into kernel?
What changes did you make when you recompiled the kernel?
 
Old 06-22-2002, 04:13 PM   #7
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
A.) Yes, I copiesd it into /bot and updated the lilo.conf. The Kernel DOES boot after all.
B.)I think I had a mix of bothmodules and directly in the kernel. Besides, emu10k-snd-0 is NOT the only thing that fails
 
Old 06-22-2002, 04:52 PM   #8
crashmeister
Senior Member
 
Registered: Feb 2002
Distribution: t2 - trying to anyway
Posts: 2,541

Rep: Reputation: 47
What is that for a version? 7.3? I think 7.3 still uses ipchains for the Suse firewall (they got different ones).
 
Old 06-22-2002, 05:16 PM   #9
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
LOL crashmeister. I really don't care about the firwewall. My feeling is whatever causes the problem for emu10k1-snd-card-0 is responsible for the failes firewall stuff.
 
Old 06-22-2002, 06:06 PM   #10
crashmeister
Senior Member
 
Registered: Feb 2002
Distribution: t2 - trying to anyway
Posts: 2,541

Rep: Reputation: 47
Why you put the errormessage there when you don't care about it??If you mean to imply that the Suse firewall isn't a part of the kernel you are of course right. I really doubt that the sound module interferes with the firewall. Now that is part of the kernel.
I forgot - just in case: If you make the firewall beeb when it detects the cracker then it might be the sound.

Last edited by crashmeister; 06-22-2002 at 06:08 PM.
 
Old 06-22-2002, 06:19 PM   #11
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
No, you misunderstood me. I put the firewall thing to demonstrate that there is a problem with modules. As for sound the sound IS working fine. I can play MP3s just fine for instance, but yet for some reason it complains about the emu10k thing at boot time.
 
Old 06-22-2002, 07:04 PM   #12
crashmeister
Senior Member
 
Registered: Feb 2002
Distribution: t2 - trying to anyway
Posts: 2,541

Rep: Reputation: 47
Thats all? I get five or six kernelmodule errors plus assorted other errors at startup. Someting about missing alsadrivers and not found sysmop - whatever that's supposed to be.Hell with it!
 
Old 06-22-2002, 07:53 PM   #13
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
Hehe, I get that too. Missing Alsa crap. Its still bothering me though
 
Old 06-22-2002, 08:15 PM   #14
Sfin
Member
 
Registered: Apr 2002
Location: Michigan
Distribution: Slackware 8.0
Posts: 197

Rep: Reputation: 30
Do this. type

dmesg

in a console, and then look through the messages that appear for the exact error that you are getting. Then post it here, so someone can know exactly what the error is.
 
Old 06-23-2002, 01:53 AM   #15
shassouneh
Member
 
Registered: Apr 2001
Location: Cheney, WA
Distribution: SuSE Linux Professional 9.2
Posts: 556

Original Poster
Rep: Reputation: 30
samer@suse:~> dmesg
Linux version 2.4.18 (root@suse) (gcc version 2.95.3 20010315 (SuSE)) #1 SMP Thu
Jun 20 03:26:02 PDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS)
BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 114672
zone(0): 4096 pages.
zone(1): 110576 pages.
zone(2): 0 pages.
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Kernel command line: auto BOOT_IMAGE=TestKernel ro root=307 BOOT_FILE=/boot/bzIm
age.myker.19jun2002 enableapic vga=0x0317 hdd=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 501.141 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 999.42 BogoMIPS
Memory: 447992k/458688k available (1846k kernel code, 10308k reserved, 601k data
, 252k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 03
per-CPU timeslice cutoff: 731.04 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 501.1576 MHz.
..... host bus clock speed is 100.2313 MHz.
cpu: 0, clocks: 1002313, slice: 501156
CPU0<T0:1002304,T1:501136,D:12,S:501156,C:1002313>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb240, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: Card '3Com 3C509B EtherLink III'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
Journalled Block Device driver loaded
NTFS driver v1.1.22 [Flags: R/O]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI IS
APNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcio, hddio
HPT366: onboard version of chipset, pin1=1 pin2=2
HPT366: IDE controller on PCI bus 00 dev 70
PCI: Found IRQ 9 for device 00:0e.0
PCI: Sharing IRQ 9 with 00:0e.1
PCI: Sharing IRQ 9 with 00:10.0
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xcc00-0xcc07, BIOS settings: hdeio, hdfio
HPT366: IDE controller on PCI bus 00 dev 71
PCI: Found IRQ 9 for device 00:0e.1
PCI: Sharing IRQ 9 with 00:0e.0
PCI: Sharing IRQ 9 with 00:10.0
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide3: BM-DMA at 0xd800-0xd807, BIOS settings: hdgio, hdhio
hda: QUANTUM FIREBALLlct08 13, ATA DISK drive
hdb: QUANTUM FIREBALLP LM30, ATA DISK drive
hdd: no response (status = 0xd0), resetting drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 25429824 sectors (13020 MB) w/418KiB Cache, CHS=25228/16/63, UDMA(33)
hdb: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63, UDMA(33)
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
eth0: 3c5x9 at 0x220, 10baseT port, address 00 60 97 3b 7c 2d, IRQ 5.
3c509.c:1.18a 17Nov2001becker@scyld.com
http://www.scyld.com/network/3c509.html
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 380M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xd8000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 on Intel 440BX @ 0xd8000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 1
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
es1371: version v0.30 time 03:29:11 Jun 20 2002
solo1: version v0.19 time 03:29:16 Jun 20 2002
Creative EMU10K1 PCI Audio Driver, version 0.18, 03:29:02 Jun 20 2002
PCI: Found IRQ 9 for device 00:10.0
PCI: Sharing IRQ 9 with 00:0e.0
PCI: Sharing IRQ 9 with 00:0e.1
emu10k1: EMU10K1 rev 5 model 0x8023 found, IO at 0xdc00-0xdc1f, IRQ 9
ac97_codec: AC97 codec, id: 0x5452:0x4123 (TriTech TR A5)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 10 for device 00:07.2
uhci.c: USB UHCI at I/O 0xc000, IRQ 10
usb.c: new USB bus registered, assigned bus number 1
uhci.c: detected 2 ports
usb.c: kmalloc IF c174cec0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI-alt Root Hub
SerialNumber: c000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c174cec0
usb.c: call_policy add, num 1 -- no FS yet
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
NET4: AppleTalk 0.18a for Linux NET4.0
ds: no socket drivers loaded!
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
request_module[nls_iso8859-1]: Root fs not mounted
Unable to load NLS charset iso8859-1
uhci.c: c000: suspend_hc
reiserfs:warning: CONFIG_REISERFS_CHECK is set ON
reiserfs:warning: - it is slow mode for debugging.
reiserfs: checking transaction log (device 03:07) ...
journal-1153: found in header: first_unflushed_offset 3156, last_flushed_trans_i
d 155278
journal-1206: Starting replay from offset 3156, trans_id 155279
journal-1299: Setting newest_mount_id to 59
Using r5 hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 252k freed
Adding Swap: 453056k swap-space (priority 42)
reiserfs:warning: CONFIG_REISERFS_CHECK is set ON
reiserfs:warning: - it is slow mode for debugging.
reiserfs: checking transaction log (device 03:05) ...
journal-1153: found in header: first_unflushed_offset 3527, last_flushed_trans_i
d 972
journal-1206: Starting replay from offset 3527, trans_id 973
journal-1299: Setting newest_mount_id to 59
Using r5 hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
eth0: Setting Rx mode to 1 addresses.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
New kernel fails to boot: It can't find modules.dep though it's there lixy Linux - General 2 04-16-2005 08:23 AM
unable to compile new modules in the kernel Menestrel Slackware 1 01-09-2005 06:41 AM
Upgraded Kernel via upgradepkg Can't Find Modules KingofBLASH Slackware 2 03-03-2004 08:13 PM
how to find out what modules are in my kernel Culbert Linux - General 5 09-08-2003 11:30 AM
Updated RH9 Kernel can't find modules morgan Linux - General 1 05-25-2003 03:50 PM


All times are GMT -5. The time now is 08:11 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration