LinuxQuestions.org
Review your favorite Linux distribution.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Server
User Name
Password
Linux - Server This forum is for the discussion of Linux Software used in a server related context.

Notices

Reply
 
Search this Thread
Old 02-18-2008, 10:52 PM   #1
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Rep: Reputation: 15
Unable to administer CUPS on Fedora 7 x86_64


I'm attempting to install a HP LaserJet 1018 on my Fedora 7 x86_64 system. I've installed foo2zjs from source. When I run system-config-printer from the terminal, the dialog box opens, but I am unable to add a printer because the dialog freezes. Same sort of issue with the KDE Control Center. I've tried using the web interface, but I can only open the index page and no others. Any ideas? I've tried updating CUPS, updating Ghostscript (not sure if it was successful), and re-installing foo2zjs. Thank you.
 
Old 02-18-2008, 10:59 PM   #2
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
Perhaps stick to the web interface.

Have a look at /etc/cups/cups.conf (I'm guessing at teh config file name here but I think the path is correct), and make sure that the access is set correctly.

Make sure cups is running.

I assume that you are running apache or similar.

See how you go and post an update when yopu get a chance
 
Old 02-18-2008, 11:12 PM   #3
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
Are you refering to the cupsd.conf file permissions? It's set as read/write for owner, read for group, and read/write for others. CUPS is running.
 
Old 02-19-2008, 01:13 AM   #4
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
Actually, I meant have a look in the file and see if there were any obvious blocks, but ptobably won't help a lot

Now, when you try to access through the web, try

https://localhost:631

Note that I specify https because some of the pages will require encryption.

If you can't get in, please look at /var/log/cups/error_log and maybe access_log and post anything that looks relevant
 
Old 02-19-2008, 09:14 PM   #5
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
Using https makes no difference. The log file has this sort of stuff all through it:

I [18/Feb/2008:15:13:42 -0600] Installing config file "/etc/cups/cupsd.conf"...
E [18/Feb/2008:15:13:42 -0600] Unable to remove backup config file "/etc/cups/cupsd.conf.O" - Permission denied
I [18/Feb/2008:15:14:27 -0600] Installing config file "/etc/cups/cupsd.conf"...
E [18/Feb/2008:15:14:27 -0600] Unable to remove backup config file "/etc/cups/cupsd.conf.O" - Permission denied
I [18/Feb/2008:21:33:16 -0600] commptr="?OP=add-printer"
I [18/Feb/2008:21:33:16 -0600] Started "/usr/lib64/cups/cgi-bin/admin.cgi" (pid=27199)
E [18/Feb/2008:21:33:16 -0600] PID 27199 (/usr/lib64/cups/cgi-bin/admin.cgi) stopped with status 22!
I [18/Feb/2008:21:33:16 -0600] Hint: Try setting the LogLevel to "debug" to find out more.
I [18/Feb/2008:23:07:43 -0600] commptr="?OP=add-printer"
I [18/Feb/2008:23:07:43 -0600] Started "/usr/lib64/cups/cgi-bin/admin.cgi" (pid=27861)
E [18/Feb/2008:23:07:43 -0600] PID 27861 (/usr/lib64/cups/cgi-bin/admin.cgi) stopped with status 22!
I [18/Feb/2008:23:07:43 -0600] Hint: Try setting the LogLevel to "debug" to find out more.
I [19/Feb/2008:21:06:23 -0600] Generating SSL server key...
I [19/Feb/2008:21:06:24 -0600] Created SSL server key file "/etc/cups/ssl/server.key"...
I [19/Feb/2008:21:06:24 -0600] Generating self-signed SSL certificate...
I [19/Feb/2008:21:06:24 -0600] Created SSL server certificate file "/etc/cups/ssl/server.crt"...
E [19/Feb/2008:21:06:32 -0600] encrypt_client: Unable to encrypt connection from localhost!
E [19/Feb/2008:21:06:32 -0600] encrypt_client: Error in the push function.
I [19/Feb/2008:21:06:37 -0600] commptr="?OP=add-printer"
I [19/Feb/2008:21:06:37 -0600] Started "/usr/lib64/cups/cgi-bin/admin.cgi" (pid=2308)
E [19/Feb/2008:21:06:37 -0600] PID 2308 (/usr/lib64/cups/cgi-bin/admin.cgi) stopped with status 22!
I [19/Feb/2008:21:06:37 -0600] Hint: Try setting the LogLevel to "debug" to find out more.
I [19/Feb/2008:21:07:34 -0600] cupsdCloseClient: SSL shutdown successful!

I have a somewhat decent understanding of what it is trying to do, but I have no idea what is stopping it from working. It did at one point a few months ago, but I had enough problems with printer drivers that I said forget it at that time. Now I'm starting over.
 
Old 02-19-2008, 09:16 PM   #6
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
Did you try setting the loglevel to debug as the logs suggest?

I'll check some permissions for you later
 
Old 02-19-2008, 09:26 PM   #7
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
After changing the loglevel here is the output for trying to add a printer from localhost:631 :

I [19/Feb/2008:21:22:50 -0600] Saving remote.cache...
I [19/Feb/2008:21:22:50 -0600] Loaded configuration file "/etc/cups/cupsd.conf"
D [19/Feb/2008:21:22:50 -0600] Repairing access permissions of "/etc/cups/cupsd.conf"
I [19/Feb/2008:21:22:50 -0600] Cleaning out old temporary files in "/var/spool/cups/tmp"...
I [19/Feb/2008:21:22:50 -0600] Configured for up to 100 clients.
I [19/Feb/2008:21:22:50 -0600] Allowing up to 100 client connections per host.
I [19/Feb/2008:21:22:50 -0600] Using policy "default" as the default!
I [19/Feb/2008:21:22:50 -0600] Full reload is required.
I [19/Feb/2008:21:22:50 -0600] Saving job cache file "/var/cache/cups/job.cache"...
I [19/Feb/2008:21:22:50 -0600] Loaded MIME database from '/etc/cups': 34 types, 0 filters...
I [19/Feb/2008:21:22:50 -0600] Loading job cache file "/var/cache/cups/job.cache"...
I [19/Feb/2008:21:22:50 -0600] Full reload complete.
E [19/Feb/2008:21:23:07 -0600] Unable to find IP address for server name "Maxwell-CUPS"!
I [19/Feb/2008:21:23:07 -0600] Listening to :::631 on fd 3...
I [19/Feb/2008:21:23:07 -0600] Listening to 0.0.0.0:631 on fd 4...
I [19/Feb/2008:21:23:07 -0600] Listening to /var/run/cups/cups.sock on fd 5...
D [19/Feb/2008:21:23:22 -0600] cupsdAcceptClient: skipping getpeercon()
D [19/Feb/2008:21:23:22 -0600] cupsdAcceptClient: 9 from localhost:631 (IPv4)
D [19/Feb/2008:21:23:22 -0600] cupsdReadClient: 9 GET /admin?OP=add-printer HTTP/1.1
D [19/Feb/2008:21:23:22 -0600] cupsdReadClient: 9 Browser asked for language "en-us.UTF-8"...
D [19/Feb/2008:21:23:22 -0600] cupsdAuthorize: No authentication data provided.
I [19/Feb/2008:21:23:22 -0600] commptr="?OP=add-printer"
D [19/Feb/2008:21:23:22 -0600] CGI /usr/lib64/cups/cgi-bin/admin.cgi started - PID = 2739
I [19/Feb/2008:21:23:22 -0600] Started "/usr/lib64/cups/cgi-bin/admin.cgi" (pid=2739)
D [19/Feb/2008:21:23:22 -0600] cupsdSendCommand: 9 file=10
D [19/Feb/2008:21:23:22 -0600] [CGI] /usr/lib64/cups/cgi-bin/admin.cgi: No such file or directory
E [19/Feb/2008:21:23:22 -0600] PID 2739 (/usr/lib64/cups/cgi-bin/admin.cgi) stopped with status 22!
D [19/Feb/2008:21:23:39 -0600] cupsdCloseClient: 9
 
Old 02-19-2008, 09:41 PM   #8
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
Interesting lines to me are

Unable to find IP address for server name "Maxwell-CUPS"!

and

/usr/lib64/cups/cgi-bin/admin.cgi: No such file or directory

What is Maxwell-CUPS, and what is in /usr/lib64/cups/cgi-bin/ ?
 
Old 02-19-2008, 09:49 PM   #9
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
Maxwell-CUPS is the server name I've given to the print server. As for the /usr/lib64/cups/cgi-bin, I couldn't tell you. /usr/lib64/cups doesn't exist.
 
Old 02-19-2008, 09:53 PM   #10
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
Let me have a look when I'm at a Fedora box (be a few hours)
Can local machine resolve Maxwell-CUPS (is it in hosts?)
 
Old 02-19-2008, 09:58 PM   #11
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
Maxwell-CUPS is the local machine. In cupsd.conf:

# Server

# Server name (ServerName)
#
# The hostname of your server, as advertised to the world.
# By default CUPS will use the hostname of the system.
#
# To set the default server used by clients, see the client.conf file.
#
# ex: myhost.domain.com
#
#ServerName myhost.domain.com

ServerName Maxwell-CUPS
 
Old 02-19-2008, 09:59 PM   #12
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
OK - I'll come back later
 
Old 02-20-2008, 01:32 AM   #13
billymayday
Guru
 
Registered: Mar 2006
Location: Sydney, Australia
Distribution: Fedora, CentOS, OpenSuse, Slack, Gentoo, Debian, Arch, PCBSD
Posts: 6,678

Rep: Reputation: 122Reputation: 122
According to man cupsd.conf, ServerName should be a FQDN, not just a name. Try commenting that out (I note that I don't have a ServerName defined in my Fedora cupsd.conf) and see if that changes at least the logs

Not sure about the admin.cgi reference - it seems to reside in /usr/lib/cups/cgi-bin

Can you post your cupsd.conf?
 
Old 02-20-2008, 11:41 PM   #14
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
The logs don't appear to be changing in content. Here is the cupsd.conf file:

# CUPS configuration file, generated by CUPS configuration tool.
# This tool is part of KDEPrint, the printing framework for KDE
# since version 2.2.2 and is used by the CUPS supporting module
# in KDEPrint. The predecessors to KDEPrint in former KDE releases
# were KUPS and QtCUPS; they are deprecated and no longer maintained.
#
# Author: Michael Goffioul
#
# Web site: http://printing.kde.org/
#
########################################################################
# #
# This is the CUPS configuration file. If you are familiar with #
# Apache or any of the other popular web servers, we've followed the #
# same format. Any configuration variable used here has the same #
# semantics as the corresponding variable in Apache. If we need #
# different functionality then a different name is used to avoid #
# confusion... #
# #
########################################################################
#

# Server

# Server name (ServerName)
#
# The hostname of your server, as advertised to the world.
# By default CUPS will use the hostname of the system.
#
# To set the default server used by clients, see the client.conf file.
#
# ex: myhost.domain.com
#
#ServerName myhost.domain.com

ServerName Maxwell-CUPS

# Server administrator (ServerAdmin)
#
# The email address to send all complaints or problems to.
# By default CUPS will use "root@hostname".
#
# ex: root@myhost.com
#
#ServerAdmin root@your.domain.com

ServerAdmin root

# Classification (Classification)
#
# The classification level of the server. If set, this
# classification is displayed on all pages, and raw printing is disabled.
# The default is the empty string.
#
# ex: confidential
#
#Classification classified

Classification none

# Allow overrides (ClassifyOverride)
#
# Whether to allow users to override the classification
# on printouts. If enabled, users can limit banner pages to before or
# after the job, and can change the classification of a job, but cannot
# completely eliminate the classification or banners.
#
# The default is off.
#
#ClassifyOverride off


# Default character set (DefaultCharset)
#
# The default character set to use. If not specified,
# defaults to utf-8. Note that this can also be overridden in
# HTML documents...
#
# ex: utf-8
#
#DefaultCharset utf-8

DefaultCharset UTF-8

# Default language (DefaultLanguage)
#
# The default language if not specified by the browser.
# If not specified, the current locale is used.
#
# ex: en
#
#DefaultLanguage en

DefaultLanguage en

# Printcap file (Printcap)
#
# The name of the printcap file. Default is no filename.
# Leave blank to disable printcap file generation.
#
# ex: /etc/printcap
#
#Printcap /etc/printcap

Printcap /etc/printcap


PrintcapFormat BSD

# Security

# Remote root user (RemoteRoot)
#
# The name of the user assigned to unauthenticated accesses
# from remote systems. By default "remroot".
#
# ex: remroot
#
#RemoteRoot remroot

RemoteRoot remroot

# System group (SystemGroup)
#
# The group name for "System" (printer administration)
# access. The default varies depending on the operating system, but
# will be sys, system, or root (checked for in that order).
#
# ex: sys
#
#SystemGroup sys

SystemGroup sys root

# Encryption certificate (ServerCertificate)
#
# The file to read containing the server's certificate.
# Defaults to "/etc/cups/ssl/server.crt".
#
# ex: /etc/cups/ssl/server.crt
#
#ServerCertificate /etc/cups/ssl/server.crt

ServerCertificate /etc/cups/ssl/server.crt

# Encryption key (ServerKey)
#
# The file to read containing the server's key.
# Defaults to "/etc/cups/ssl/server.key".
#
# ex: /etc/cups/ssl/server.key
#
#ServerKey /etc/cups/ssl/server.key

ServerKey /etc/cups/ssl/server.key

# Access permissions
#
# Access permissions for each directory served by the scheduler.
# Locations are relative to DocumentRoot...
#
# AuthType: the authorization to use:
#
# None - Perform no authentication
# Basic - Perform authentication using the HTTP Basic method.
# Digest - Perform authentication using the HTTP Digest method.
#
# (Note: local certificate authentication can be substituted by
# the client for Basic or Digest when connecting to the
# localhost interface)
#
# AuthClass: the authorization class; currently only Anonymous, User,
# System (valid user belonging to group SystemGroup), and Group
# (valid user belonging to the specified group) are supported.
#
# AuthGroupName: the group name for "Group" authorization.
#
# Order: the order of Allow/Deny processing.
#
# Allow: allows access from the specified hostname, domain, IP address, or
# network.
#
# Deny: denies access from the specified hostname, domain, IP address, or
# network.
#
# Both "Allow" and "Deny" accept the following notations for addresses:
#
# All
# None
# *.domain.com
# .domain.com
# host.domain.com
# nnn.*
# nnn.nnn.*
# nnn.nnn.nnn.*
# nnn.nnn.nnn.nnn
# nnn.nnn.nnn.nnn/mm
# nnn.nnn.nnn.nnn/mmm.mmm.mmm.mmm
#
# The host and domain address require that you enable hostname lookups
# with "HostNameLookups On" above.
#
# Encryption: whether or not to use encryption; this depends on having
# the OpenSSL library linked into the CUPS library and scheduler.
#
# Possible values:
#
# Always - Always use encryption (SSL)
# Never - Never use encryption
# Required - Use TLS encryption upgrade
# IfRequested - Use encryption if the server requests it
#
# The default value is "IfRequested".
#
#<Location [resource_name]>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#
## Anonymous access (default)
#AuthType None
#
## Require a username and password (Basic authentication)
#AuthType Basic
#AuthClass User
#
## Require a username and password (Digest/MD5 authentication)
#AuthType Digest
#AuthClass User
#
## Restrict access to local domain
#Order Deny,Allow
#Deny From All
#Allow From .mydomain.com
#
## Use encryption if requested
#Encryption IfRequested
#</Location>

<Location />
Encryption IfRequested
Satisfy All
Order allow,deny
Allow @LOCAL
</Location>
<Location /admin>
Encryption Required
Satisfy All
Order allow,deny
Allow localhost
</Location>
<Location /admin/conf>
AuthType Basic
Require user @SYSTEM
Encryption IfRequested
Satisfy All
Order allow,deny
Allow localhost
</Location>

# Network

# Hostname lookups (HostNameLookups)
#
# Whether or not to do lookups on IP addresses to get a
# fully-qualified hostname. This defaults to Off for performance reasons...
#
# ex: On
#
#HostNameLookups On

HostnameLookups On

# Keep alive (KeepAlive)
#
# Whether or not to support the Keep-Alive connection
# option. Default is on.
#
# ex: On
#
#KeepAlive On

KeepAlive On

# Keep-alive timeout (KeepAliveTimeout)
#
# The timeout (in seconds) before Keep-Alive connections are
# automatically closed. Default is 60 seconds.
#
# ex: 60
#
#KeepAliveTimeout 60

KeepAliveTimeout 60

# Max clients (MaxClients)
#
# Controls the maximum number of simultaneous clients that
# will be handled. Defaults to 100.
#
# ex: 100
#
#MaxClients 100

MaxClients 100

# Max request size (MaxRequestSize)
#
# Controls the maximum size of HTTP requests and print files.
# Set to 0 to disable this feature (defaults to 0).
#
# ex: 0
#
#MaxRequestSize 0

MaxRequestSize 0m

# Client timeout (Timeout)
#
# The timeout (in seconds) before requests time out. Default is 300 seconds.
#
# ex: 300
#
#Timeout 300

Timeout 300

# Listen to (Port/Listen)
#
# Ports/addresses that are listened to. The default port 631 is reserved
# for the Internet Printing Protocol (IPP) and is what is used here.
#
# You can have multiple Port/Listen lines to listen to more than one
# port or address, or to restrict access.
#
# Note: Unfortunately, most web browsers don't support TLS or HTTP Upgrades
# for encryption. If you want to support web-based encryption you will
# probably need to listen on port 443 (the "HTTPS" port...).
#
# ex: 631, myhost:80, 1.2.3.4:631
#
# Port 80
# Port 631
# Listen hostname
# Listen hostname:80
# Listen hostname:631
# Listen 1.2.3.4
# Listen 1.2.3.4:631
#
#Port 631

Listen *:631
Listen /var/run/cups/cups.sock

# Log

# Access log (AccessLog)
#
# The access log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/access_log".
#
# You can also use the special name syslog to send the output to the
# syslog file or daemon.
#
# ex: /var/log/cups/access_log
#
#AccessLog /var/log/cups/access_log

AccessLog /var/log/cups/access_log

# Error log (ErrorLog)
#
# The error log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/error_log".
#
# You can also use the special name syslog to send the output to the
# syslog file or daemon.
#
# ex: /var/log/cups/error_log
#
#ErrorLog /var/log/cups/error_log

ErrorLog /var/log/cups/error_log

# Page log (PageLog)
#
# The page log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/page_log".
#
# You can also use the special name syslog to send the output to the
# syslog file or daemon.
#
# ex: /var/log/cups/page_log
#
#PageLog /var/log/cups/page_log

PageLog /var/log/cups/page_log

# Max log size (MaxLogSize)
#
# Controls the maximum size of each log file before they are
# rotated. Defaults to 1048576 (1MB). Set to 0 to disable log rotating.
#
# ex: 1048576
#
#MaxLogSize 0

MaxLogSize 1m

# Log level (LogLevel)
#
# Controls the number of messages logged to the ErrorLog
# file and can be one of the following:
#
# debug2: Log everything.
# debug: Log almost everything.
# info: Log all requests and state changes.
# warn: Log errors and warnings.
# error: Log only errors.
# none: Log nothing.
#
# ex: info
#
#LogLevel info

LogLevel debug

# Jobs

# Preserve job history (PreserveJobHistory)
#
# Whether or not to preserve the job history after a
# job is completed, canceled, or stopped. Default is Yes.
#
# ex: Yes
#
#PreserveJobHistory Yes

PreserveJobHistory On

# Preserve job files (PreserveJobFiles)
#
# Whether or not to preserve the job files after a
# job is completed, canceled, or stopped. Default is No.
#
# ex: No
#
#PreserveJobFiles No

PreserveJobFiles Off

# Auto purge jobs (AutoPurgeJobs)
#
# Automatically purge jobs when not needed for quotas.
# Default is No.
#
#AutoPurgeJobs No

AutoPurgeJobs No

# Max jobs (MaxJobs)
#
# Maximum number of jobs to keep in memory (active and completed).
# Default is 0 (no limit).
#
#MaxJobs 0

MaxJobs 0

# Max jobs per printer (MaxJobsPerPrinter)
#
# The MaxJobsPerPrinter directive controls the maximum number of active
# jobs that are allowed for each printer or class. Once a printer or class
# reaches the limit, new jobs will be rejected until one of the active jobs
# is completed, stopped, aborted, or canceled.
#
# Setting the maximum to 0 disables this functionality.
# Default is 0 (no limit).
#
#
#MaxJobsPerPrinter 0

MaxJobsPerPrinter 0

# Max jobs per user (MaxJobsPerUser)
#
# The MaxJobsPerUser directive controls the maximum number of active
# jobs that are allowed for each user. Once a user reaches the limit, new
# jobs will be rejected until one of the active jobs is completed, stopped,
# aborted, or canceled.
#
# Setting the maximum to 0 disables this functionality.
# Default is 0 (no limit).
#
#
#MaxJobsPerUser 0

MaxJobsPerUser 0

# Filter

# User (User)
#
# The user the server runs under. Normally this
# must be lp, however you can configure things for another user
# as needed.
#
# Note: the server must be run initially as root to support the
# default IPP port of 631. It changes users whenever an external
# program is run...
#
# ex: lp
#
#User lp

User lp

# Group (Group)
#
# The group the server runs under. Normally this
# must be sys, however you can configure things for another
# group as needed.
#
# ex: lp
#
#Group lp

Group lp

# RIP cache (RIPCache)
#
# The amount of memory that each RIP should use to cache
# bitmaps. The value can be any real number followed by "k" for
# kilobytes, "m" for megabytes, "g" for gigabytes, or "t" for tiles
# (1 tile = 256x256 pixels). Defaults to "8m" (8 megabytes).
#
# ex: 8m
#
#RIPCache 8m

RIPCache 8m

# Filter limit (FilterLimit)
#
# Sets the maximum cost of all job filters that can be run
# at the same time. A limit of 0 means no limit. A typical job may need
# a filter limit of at least 200; limits less than the minimum required
# by a job force a single job to be printed at any time.
#
# The default limit is 0 (unlimited).
#
# ex: 200
#
#FilterLimit 0

FilterLimit 0

# Directories

# Data directory (DataDir)
#
# The root directory for the CUPS data files.
# By default /usr/share/cups.
#
# ex: /usr/share/cups
#
#DataDir /usr/share/cups

DataDir /usr/share/cups

# Document directory (DocumentRoot)
#
# The root directory for HTTP documents that are served.
# By default the compiled-in directory.
#
# ex: /usr/share/cups/doc
#
#DocumentRoot /usr/share/cups/doc

DocumentRoot /usr/share/cups/doc

# Font path (FontPath)
#
# The path to locate all font files (currently only for pstoraster).
# By default /usr/share/cups/fonts.
#
# ex: /usr/share/cups/fonts
#
#FontPath /usr/share/cups/fonts


# Request directory (RequestRoot)
#
# The directory where request files are stored.
# By default /var/spool/cups.
#
# ex: /var/spool/cups
#
#RequestRoot /var/spool/cups

RequestRoot /var/spool/cups

# Server binaries (ServerBin)
#
# The root directory for the scheduler executables.
# By default /usr/lib/cups or /usr/lib32/cups (IRIX 6.5).
#
# ex: /usr/lib/cups
#
#ServerBin /usr/lib/cups

ServerBin /usr/lib64/cups

# Server files (ServerRoot)
#
# The root directory for the scheduler.
# By default /etc/cups.
#
# ex: /etc/cups
#
#ServerRoot /etc/cups

ServerRoot /etc/cups

# Temporary files (TempDir)
#
# The directory to put temporary files in. This directory must be
# writable by the user defined above! Defaults to "/var/spool/cups/tmp" or
# the value of the TMPDIR environment variable.
#
# ex: /var/spool/cups/tmp
#
#TempDir /var/spool/cups/tmp

TempDir /var/spool/cups/tmp

# Browsing

# Use browsing (Browsing)
#
# Whether or not to listen to printer
# information from other CUPS servers.
#
#
# Enabled by default.
#
#
# Note: to enable the sending of browsing
# information from this CUPS server to the LAN,
# specify a valid BrowseAddress.
#
#
# ex: On
#
#Browsing On

Browsing On

# Browse protocols (BrowseProtocols)
#
# Which protocols to use for browsing. Can be
# any of the following separated by whitespace and/or commas:
#
# all - Use all supported protocols.
# cups - Use the CUPS browse protocol.
# slp - Use the SLPv2 protocol.
#
# The default is cups.
#
# Note: If you choose to use SLPv2, it is strongly recommended that
# you have at least one SLP Directory Agent (DA) on your
# network. Otherwise, browse updates can take several seconds,
# during which the scheduler will not response to client
# requests.
#
#BrowseProtocols cups

BrowseProtocols CUPS

# Browse port (BrowsePort)
#
# The port used for UDP broadcasts. By default this is
# the IPP port; if you change this you need to do it on all servers.
# Only one BrowsePort is recognized.
#
# ex: 631
#
#BrowsePort 631

BrowsePort 631

# Browse interval (BrowseInterval)
#
# The time between browsing updates in seconds. Default
# is 30 seconds.
#
# Note that browsing information is sent whenever a printer's state changes
# as well, so this represents the maximum time between updates.
#
# Set this to 0 to disable outgoing broadcasts so your local printers are
# not advertised but you can still see printers on other hosts.
#
# ex: 30
#
#BrowseInterval 30

BrowseInterval 30

# Browse timeout (BrowseTimeout)
#
# The timeout (in seconds) for network printers - if we don't
# get an update within this time the printer will be removed
# from the printer list. This number definitely should not be
# less the BrowseInterval value for obvious reasons. Defaults
# to 300 seconds.
#
# ex: 300
#
#BrowseTimeout 300

BrowseTimeout 300

# Browse addresses (BrowseAddress)
#
# Specifies a broadcast address to be used. By
# default browsing information is broadcast to all active interfaces.
#
# Note: HP-UX 10.20 and earlier do not properly handle broadcast unless
# you have a Class A, B, C, or D netmask (i.e. no CIDR support).
#
# ex: x.y.z.255, x.y.255.255
#
#BrowseAddress x.y.z.255
#BrowseAddress x.y.255.255
#BrowseAddress x.255.255.255

BrowseAllow @LOCAL

# Browse order (BrowseOrder)
#
# Specifies the order of BrowseAllow/BrowseDeny comparisons.
#
# ex: allow,deny
#
#BrowseOrder allow,deny
#BrowseOrder deny,allow

BrowseOrder allow,deny

# Implicit classes (ImplicitClasses)
#
# Whether or not to use implicit classes.
#
# Printer classes can be specified explicitly in the classes.conf
# file, implicitly based upon the printers available on the LAN, or
# both.
#
# When ImplicitClasses is On, printers on the LAN with the same name
# (e.g. Acme-LaserPrint-1000) will be put into a class with the same
# name. This allows you to setup multiple redundant queues on a LAN
# without a lot of administrative difficulties. If a user sends a
# job to Acme-LaserPrint-1000, the job will go to the first available
# queue.
#
# Enabled by default.
#
#ImplicitClasses Off

ImplicitClasses On

# Use &quot;any&quot; classes (ImplicitAnyClasses)
#
# Whether or not to create AnyPrinter implicit
# classes.
#
# When ImplicitAnyClasses is On and a local queue of the same name
# exists, e.g. "printer", "printer@server1", "printer@server1", then
# an implicit class called "Anyprinter" is created instead.
#
# When ImplicitAnyClasses is Off, implicit classes are not created
# when there is a local queue of the same name.
#
# Disabled by default.
#
#ImplicitAnyCLasses Off

ImplicitAnyClasses Off

# Hide implicit members (HideImplicitMembers)
#
# Whether or not to show the members of an
# implicit class.
#
# When HideImplicitMembers is On, any remote printers that are
# part of an implicit class are hidden from the user, who will
# then only see a single queue even though many queues will be
# supporting the implicit class.
#
# Enabled by default.
#
#HideImplicitMembers On

HideImplicitMembers Yes

# Use short names (BrowseShortNames)
#
# Whether or not to use "short" names for remote printers
# when possible (e.g. "printer" instead of "printer@host"). Enabled by
# default.
#
# ex: Yes
#
#BrowseShortNames Yes

BrowseShortNames Yes

# Unknown
defaultauthtype Basic
<policy default>
<limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job>
require user @OWNER @SYSTEM
order deny,allow
</limit>
<limit Pause-Printer Resume-Printer Set-Printer-Attributes Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Add-Printer CUPS-Delete-Printer CUPS-Add-Class CUPS-Delete-Class CUPS-Accept-Jobs CUPS-Reject-Jobs CUPS-Set-Default>
authtype Basic
require user @SYSTEM
order deny,allow
</limit>
<limit Cancel-Job CUPS-Authenticate-Job>
require user @OWNER @SYSTEM
order deny,allow
</limit>
<limit All>
order deny,allow
</limit>
</policy>
 
Old 02-24-2008, 09:22 PM   #15
rcx11
Member
 
Registered: Oct 2006
Distribution: Fedora 7 x86_64, SLAX
Posts: 58

Original Poster
Rep: Reputation: 15
I've made the change in the server name to maxwell.ags-crowder.zapto.org (the FQDN of the machine). Any ideas?
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Unable to start HAL (haldaemon) on Fedora 8 x86_64 PsychosisNode Fedora 3 11-15-2007 12:43 AM
Unable to install CUPs JOsterheim Mandriva 2 07-27-2007 07:52 PM
Unable to print pdfs using CUPS Fegenbush Linux - Software 1 01-26-2007 05:35 AM
Opera 8.54 worked fine with Mandrake 10.1. Unable to install for Mandriva 06 x86_64 wkramer Mandriva 2 04-21-2006 04:36 AM
Unable to print to IBM InfoPrint 40 using CUPS system under Fedora Core 2 NoPlan Linux - Newbie 1 04-19-2004 05:58 PM


All times are GMT -5. The time now is 12:27 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration