Unable to mount data hard drive w/ file system LVM2 on fedora12
Upgraded from fc12 to fc14 using yum upgrade. fc 14 boots, but can't log in as user or root. passwords not accepted. removed hard drive and installed new blank drive then reinstalled fc12 on drive (primary master) connected old drive as primary slave. created directory /mnt/sdb1 and tried as root to mount (mount /dev/sdb1 /mnt/sdb1) and get:
mount: unknown filesystem type 'LVM2_member' gparted finds both drives (sda1 ext4 mounted boot, sda2 lvm2 not mounted?) & sdb1 lvm2 not mounted and returns the warning "lvm is not yet supported" Thanks in advance Output for fdisk-l and dmesg follows ran as root fdisk -l output: Disk /dev/sda: 82.0 GB, 81964302336 bytes 255 heads, 63 sectors/track, 9964 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b8b63 Device Boot Start End Blocks Id System /dev/sda1 * 1 26 204800 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 26 9964 79830998+ 8e Linux LVM Disk /dev/sdb: 20.0 GB, 20020396032 bytes 255 heads, 63 sectors/track, 2434 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000e6021 Device Boot Start End Blocks Id System /dev/sdb1 1 2434 19551073+ 83 Linux Disk /dev/dm-0: 1073 MB, 1073741824 bytes 255 heads, 63 sectors/track, 130 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 78.6 GB, 78555119616 bytes 255 heads, 63 sectors/track, 9550 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 3187 MB, 3187671040 bytes 255 heads, 63 sectors/track, 387 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table ran as root dmesg output: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) DMI 2.3 present. last_pfn = 0x5ffec max_arch_pfn = 0x1000000 MTRR default type: uncachable MTRR fixed ranges enabled: 00000-9FFFF write-back A0000-FFFFF uncachable MTRR variable ranges enabled: 0 base 000000000 mask FC0000000 write-back 1 base 040000000 mask FE0000000 write-back 2 disabled 3 disabled 4 disabled 5 disabled 6 disabled 7 base 0E6000000 mask FFE000000 write-combining x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 initial memory mapped : 0 - 01000000 init_memory_mapping: 0000000000000000-00000000375fe000 Using x86 segment limits to approximate NX protection 0000000000 - 0000200000 page 4k 0000200000 - 0037400000 page 2M 0037400000 - 00375fe000 page 4k kernel direct mapping tables up to 375fe000 @ 7000-f000 RAMDISK: 37470000 - 37fefd2d Allocated new RAMDISK: 00b6b000 - 016ead2d Move RAMDISK from 0000000037470000 - 0000000037fefd2c to 00b6b000 - 016ead2c ACPI: RSDP 000f6a70 00014 (v00 ASUS ) ACPI: RSDT 5ffec000 0002C (v01 ASUS A7V-133 30303031 MSFT 31313031) ACPI: FACP 5ffec080 00074 (v01 ASUS A7V-133 30303031 MSFT 31313031) ACPI: DSDT 5ffec100 02CE1 (v01 ASUS A7V-133 00001000 MSFT 0100000B) ACPI: FACS 5ffff000 00040 ACPI: BOOT 5ffec040 00028 (v01 ASUS A7V-133 30303031 MSFT 31313031) 649MB HIGHMEM available. 885MB LOWMEM available. mapped low ram: 0 - 375fe000 low ram: 0 - 375fe000 node 0 low ram: 00000000 - 375fe000 node 0 bootmap 0000b000 - 00011ec0 (9 early reservations) ==> bootmem [0000000000 - 00375fe000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000400000 - 0000b61c38] TEXT DATA BSS ==> [0000400000 - 0000b61c38] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #5 [0000b62000 - 0000b6a150] BRK ==> [0000b62000 - 0000b6a150] #6 [0000007000 - 000000b000] PGTABLE ==> [0000007000 - 000000b000] #7 [0000b6b000 - 00016ead2d] NEW RAMDISK ==> [0000b6b000 - 00016ead2d] #8 [000000b000 - 0000012000] BOOTMAP ==> [000000b000 - 0000012000] Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x000375fe HighMem 0x000375fe -> 0x0005ffec Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x0005ffec On node 0 totalpages: 393099 free_area_init_node: node 0, pgdat c09d8a80, node_mem_map c16ec000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3967 pages, LIFO batch:0 Normal zone: 1740 pages used for memmap Normal zone: 220978 pages, LIFO batch:31 HighMem zone: 1300 pages used for memmap HighMem zone: 165082 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0xe408 SMP: Allowing 1 CPUs, 0 hotplug CPUs Local APIC disabled by BIOS -- you can enable it with "lapic" APIC: disable apic facility nr_irqs_gsi: 16 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 60000000 (gap: 60000000:9fff0000) Booting paravirtualized kernel on bare hardware NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 PERCPU: Embedded 15 pages/cpu @c2400000 s37848 r0 d23592 u2097152 pcpu-alloc: s37848 r0 d23592 u2097152 alloc=1*2097152 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390027 Kernel command line: ro root=/dev/mapper/VolGroup-lv_root LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 allocated 7863920 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Initializing HighMem for node 0 (000375fe:0005ffec) Memory: 1531272k/1572784k available (3764k kernel code, 40268k reserved, 2351k data, 564k init, 665528k highmem) virtual kernel memory layout: fixmap : 0xffad5000 - 0xfffff000 (5288 kB) pkmap : 0xff600000 - 0xff800000 (2048 kB) vmalloc : 0xf7dfe000 - 0xff5fe000 ( 120 MB) lowmem : 0xc0000000 - 0xf75fe000 ( 885 MB) .init : 0xc09fa000 - 0xc0a87000 ( 564 kB) .data : 0xc07ad184 - 0xc09f9060 (2351 kB) .text : 0xc0400000 - 0xc07ad184 (3764 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:1280 Console: colour VGA+ 80x25 console [tty0] enabled Fast TSC calibration using PIT Detected 1311.679 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 2623.35 BogoMIPS (lpj=1311679) Security Framework initialized SELinux: Initializing. SELinux: Starting in permissive mode Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys net_cls CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) mce: CPU supports 4 MCE banks Performance Events: AMD PMU driver. ... version: 0 ... bit width: 48 ... generic registers: 4 ... value mask: 0000ffffffffffff ... max period: 00007fffffffffff ... fixed-purpose events: 0 ... event mask: 000000000000000f Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 26k freed ACPI: Core revision 20090903 ACPI: setting ELCR to 0200 (from 0c20) ftrace: converting mcount calls to 0f 1f 44 00 00 ftrace: allocating 22767 entries in 45 pages Enabling APIC mode: Flat. Using 0 I/O APICs weird, boot CPU (#0) not listed by the BIOS. SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. SMP disabled Brought up 1 CPUs Total of 1 processors activated (2623.35 BogoMIPS). sizeof(vma)=92 bytes sizeof(page)=32 bytes sizeof(inode)=352 bytes sizeof(dentry)=132 bytes sizeof(ext3inode)=508 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=184 bytes sizeof(task_struct)=3244 bytes CPU0 attaching NULL sched-domain. devtmpfs: initialized regulator: core version 0.5 Time: 12:46:49 Date: 06/17/11 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1 PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using PIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:00.0: reg 10 32bit mmio pref: [0xe6000000-0xe7ffffff] pci 0000:00:00.0: Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09 pci 0000:00:01.0: supports D1 pci 0000:00:04.1: reg 20 io port: [0xb800-0xb80f] pci 0000:00:04.2: reg 20 io port: [0xb400-0xb41f] pci 0000:00:04.3: reg 20 io port: [0xb000-0xb01f] pci 0000:00:04.4: quirk: region e200-e27f claimed by vt82c686 HW-mon pci 0000:00:04.4: quirk: region e800-e80f claimed by vt82c686 SMB pci 0000:00:09.0: reg 10 32bit mmio: [0xce800000-0xce83ffff] pci 0000:00:09.0: reg 14 io port: [0x9400-0x9407] pci 0000:00:09.0: reg 18 io port: [0x9000-0x9007] pci 0000:00:09.0: supports D2 pci 0000:00:09.0: PME# supported from D2 D3hot pci 0000:00:09.0: PME# disabled pci 0000:00:0b.0: reg 10 io port: [0x8800-0x88ff] pci 0000:00:0b.0: reg 14 32bit mmio: [0xce000000-0xce0000ff] pci 0000:00:0b.0: reg 30 32bit mmio pref: [0x000000-0x01ffff] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D1 D2 D3hot D3cold pci 0000:00:0b.0: PME# disabled pci 0000:00:11.0: reg 10 io port: [0x8400-0x8407] pci 0000:00:11.0: reg 14 io port: [0x8000-0x8003] pci 0000:00:11.0: reg 18 io port: [0x7800-0x7807] pci 0000:00:11.0: reg 1c io port: [0x7400-0x7403] pci 0000:00:11.0: reg 20 io port: [0x7000-0x703f] pci 0000:00:11.0: reg 24 32bit mmio: [0xcd800000-0xcd81ffff] pci 0000:00:11.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xd0000000-0xdfffffff] pci 0000:01:00.0: reg 14 32bit mmio: [0xcf000000-0xcf03ffff] pci 0000:01:00.0: reg 18 io port: [0xd800-0xd87f] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xcfff0000-0xcfffffff] pci 0000:01:00.0: supports D1 D2 pci 0000:00:01.0: bridge io port: [0xd000-0xdfff] pci 0000:00:01.0: bridge 32bit mmio: [0xcf000000-0xcfdfffff] pci 0000:00:01.0: bridge 32bit mmio pref: [0xcff00000-0xe5ffffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: old code would have set cacheline size to 64 bytes, but clflush_size = 32 PCI: pci_cache_line_size set to 32 bytes NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default Switching to clocksource tsc pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered system 00:00: iomem range 0x0-0x9ffff could not be reserved system 00:00: iomem range 0xf0000-0xfffff could not be reserved system 00:00: iomem range 0x100000-0x5fffffff could not be reserved system 00:00: iomem range 0xfffe0000-0xffffffff could not be reserved system 00:02: ioport range 0x3f0-0x3f1 has been reserved system 00:02: ioport range 0x4d0-0x4d1 has been reserved system 00:03: ioport range 0xe400-0xe47f has been reserved system 00:03: ioport range 0xe800-0xe80f has been reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0xd000-0xdfff pci 0000:00:01.0: MEM window: 0xcf000000-0xcfdfffff pci 0000:00:01.0: PREFETCH window: 0xcff00000-0xe5ffffff pci 0000:00:01.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:01: resource 0 io: [0xd000-0xdfff] pci_bus 0000:01: resource 1 mem: [0xcf000000-0xcfdfffff] pci_bus 0000:01: resource 2 pref mem [0xcff00000-0xe5ffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 pci 0000:00:00.0: Applying VIA southbridge workaround pci 0000:00:01.0: disabling DAC on VIA PCI bridge pci 0000:00:04.0: Disabling VIA external APIC routing pci 0000:01:00.0: Boot video device Trying to unpack rootfs image as initramfs... Freeing initrd memory: 11775k freed Simple Boot Flag at 0x3a set to 0x1 apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) type=2000 audit(1308314809.866:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 2 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1715 SELinux: Registering netfilter hooks alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 pci-stub: invalid id string "" input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 ACPI: Power Button [PWRB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 ACPI: Power Button [PWRF] Marking TSC unstable due to TSC halts in idle processor LNXCPU:00: registered as cooling_device0 Switching to clocksource acpi_pm isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.3 Linux agpgart interface v0.103 agpgart: Detected VIA Twister-K/KT133x/KM133 chipset agpgart-via 0000:00:00.0: AGP aperture is 32M @ 0xe6000000 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A brd: module loaded loop: module loaded input: Macintosh mouse button emulation as /devices/virtual/input/input2 Fixed MDIO Bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered uhci_hcd 0000:00:04.2: PCI INT D -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:04.2: UHCI Host Controller uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:04.2: irq 5, io base 0x0000b400 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.32.26-175.fc12.i686.PAE uhci_hcd usb usb1: SerialNumber: 0000:00:04.2 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:04.3: PCI INT D -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:04.3: UHCI Host Controller uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:04.3: irq 5, io base 0x0000b000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.32.26-175.fc12.i686.PAE uhci_hcd usb usb2: SerialNumber: 0000:00:04.3 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice rtc_cmos 00:05: RTC can wake from S4 rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one year, 242 bytes nvram device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 Using IPI No-Shortcut mode PM: Resume from disk failed. registered taskstats version 1 No TPM chip found, activating TPM-bypass! Magic number: 15:783:784 rtc_cmos 00:05: setting system clock to 2011-06-17 12:46:51 UTC (1308314811) Initalizing network drop monitor service Freeing unused kernel memory: 564k freed Write protecting the kernel text: 3768k Write protecting the kernel read-only data: 1768k input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 dracut: dracut-005-5.fc12 udev: starting version 145 psmouse serio1: ID: 10 00 64 dracut: Starting plymouth daemon pata_via 0000:00:04.1: version 0.3.4 scsi0 : pata_via scsi1 : pata_via ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xb800 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xb808 irq 15 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered pata_pdc202xx_old 0000:00:11.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 scsi2 : pata_pdc202xx_old scsi3 : pata_pdc202xx_old ata3: PATA max UDMA/100 cmd 0x8400 ctl 0x8000 bmdma 0x7000 irq 10 ata4: PATA max UDMA/100 cmd 0x7800 ctl 0x7400 bmdma 0x7008 irq 10 ata1.00: ATA-7: Maxtor 4R080L0, RAMC1TU0, max UDMA/133 ata1.00: 160086528 sectors, multi 16: LBA48 ata1.01: ATA-5: MAXTOR 6L020J1, A93.0500, max UDMA/133 ata1.01: 39102336 sectors, multi 16: LBA ata1.00: configured for UDMA/100 ata1.01: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA Maxtor 4R080L0 RAMC PQ: 0 ANSI: 5 sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 0:0:1:0: Direct-Access ATA MAXTOR 6L020J1 A93. PQ: 0 ANSI: 5 sd 0:0:1:0: Attached scsi generic sg1 type 0 sd 0:0:0:0: [sda] 160086528 512-byte logical blocks: (81.9 GB/76.3 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:1:0: [sdb] 39102336 512-byte logical blocks: (20.0 GB/18.6 GiB) sd 0:0:1:0: [sdb] Write Protect is off sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 0:0:1:0: [sdb] Attached SCSI disk input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4 ata2.00: ATAPI: ASUS DVD-E616A2, CP02, max UDMA/33 ata2.00: configured for UDMA/33 scsi 1:0:0:0: CD-ROM ASUS DVD-E616A2 CP02 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 4x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg2 type 5 dracut: Scanning devices sda2 sdb1 for LVM volume groups dracut: Couldn't find device with uuid 2nhO12-pXVu-Q3H1-L1Oz-1OmA-wLq3-5gWmCj. dracut: Reading all physical volumes. This may take a while... dracut: Found volume group "vg_kck2" using metadata type lvm2 dracut: Found volume group "VolGroup" using metadata type lvm2 dracut: Couldn't find device with uuid 2nhO12-pXVu-Q3H1-L1Oz-1OmA-wLq3-5gWmCj. dracut: Refusing activation of partial LV lv_root. Use --partial to override. dracut: 1 logical volume(s) in volume group "vg_kck2" now active dracut: 2 logical volume(s) in volume group "VolGroup" now active EXT4-fs (dm-1): mounted filesystem with ordered data mode dracut: Mounted root filesystem /dev/mapper/VolGroup-lv_root dracut: Loading SELinux policy type=1404 audit(1308314814.691:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 SELinux: 8192 avtab hash slots, 165431 rules. SELinux: 8192 avtab hash slots, 165431 rules. SELinux: 8 users, 12 roles, 3133 types, 159 bools, 1 sens, 1024 cats SELinux: 77 classes, 165431 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-1, type ext4), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts type=1403 audit(1308314815.369:3): policy loaded auid=4294967295 ses=4294967295 dracut: dracut: Switching root udev: starting version 145 type=1400 audit(1308314824.445:4): avc: denied { mmap_zero } for pid=497 comm="vbetool" scontext=system_u:system_r:vbetool_t:s0-s0:c0.c1023 tcontext=system_u:system_r:vbetool_t:s0-s0:c0.c1023 tclass=memprotect ACPI: I/O resource vt596_smbus [0xe800-0xe807] conflicts with ACPI region SM00 [0xe800-0xe806] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded r8169 0000:00:0b.0: enabling device (0014 -> 0017) r8169 0000:00:0b.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 r8169 0000:00:0b.0: PCI: Disallowing DAC for device r8169 0000:00:0b.0: no PCI Express capability eth0: RTL8110s at 0xf85ba000, 00:40:f4:98:52:09, XID 04000000 IRQ 10 parport_pc: VIA 686A/8231 detected parport_pc: probing current configuration parport_pc: Current parallel port base: 0x378 parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] via686a 0000:00:04.4: Sensors disabled, enable with force_addr=0xe200 parport0: Printer, HEWLETT-PACKARD DESKJET 540 parport_pc: VIA parallel port: io=0x378, irq=7 ppdev: user-space parallel port driver au8810 0000:00:09.0: enabling device (0004 -> 0007) au8810 0000:00:09.0: PCI INT A -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5 Vortex: init.... ALSA sound/core/control.c:339: control 3:0:0:Playback PCM advanced processing:0 is already present done. Aureal Advantage 3D Sound Processor: Activating latency workaround... Aureal Advantage 3D Sound Processor: vortex latency is 0xff Aureal Advantage 3D Sound Processor: bridge config is 0x18 vortex: IRQ reg error gameport: AU88x0 Gameport is pci0000:00:09.0/gameport0, speed 1754kHz device-mapper: multipath: version 1.1.0 loaded EXT4-fs (sda1): mounted filesystem with ordered data mode SELinux: initialized (dev sda1, type ext4), uses xattr Adding 3112952k swap on /dev/mapper/VolGroup-lv_swap. Priority:-1 extents:1 across:3112952k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts NET: Registered protocol family 10 lo: Disabled Privacy Extensions ip6_tables: (C) 2000-2006 Netfilter Core Team r8169: eth0: link up r8169: eth0: link up RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts eth0: no IPv6 routers present fuse init (API version 7.13) SELinux: initialized (dev fuse, type fuse), uses genfs_contexts |
Looking at what you supplied, I suspect that /dev/sdb1 is an LVM Physical volume that is in the vg_kck2 Volume Group.
If you do a 'pvs', 'vgs' and an 'lvs' command, you should see all of the LVM info. You'll probably see two Physical Volumes, /dev/sda2 and /dev/sdb1; two Volume Groups, VolGroup and vg_kck2; two Logical Volumes, lv_root and lv_swap in the VolGroup VG; and some other Logical Volume in the vg_kck2 VG. I think the LV within vg_kck2 is what you want to be mounting. If that's not the case, post the output of your 'lvs', 'vgs, and 'pvs' commands. Back to your original issue, if your user password doesn't work, it's a simple matter to break into the system, reset it, and reboot. (You can't log in to the gui as root without making PAM changes. Another topic.) Let us know how you make out. tom btw, the message: dracut: Couldn't find device with uuid 2nhO12-pXVu-Q3H1-L1Oz-1OmA-wLq3-5gWmCj. is of mild concern. It may mean nothing. |
All times are GMT -5. The time now is 02:08 PM. |