LinuxQuestions.org
Register a domain and help support LQ
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie
User Name
Password
Linux - Newbie This Linux forum is for members that are new to Linux.
Just starting out and have a question? If it is not in the man pages or the how-to's this is the place!

Notices


Reply
  Search this Thread
Old 12-11-2007, 08:08 PM   #1
crazylegs
LQ Newbie
 
Registered: Dec 2007
Posts: 4

Rep: Reputation: 0
Network Errors on bootup


I'm new to Linux. Have programmed a lot of AIX client/server programs over the years, but never got into the "admin" end of Unix. I've setup an openSUSE 10.3 PC. Had the network interface all working until I tried to setup a network printer. Now the network interface appears to be broken. Getting the following error from the boot.msg log:


doneSetting up network interfaces:

lo

lo IP address: 127.0.0.1/8

Checking for network time protocol daemon (NTPD): unused

done eth0 device: Accton Technology Corporation SMC2-1211TX (rev 10)

eth0 IP address: 192.168.1.2/24
Checking for network time protocol daemon (NTPD): unused

doneWaiting for mandatory devices: eth0_new __NSC__
12 11 10 9 6 5 4 3 1 0

eth0_new No interface found

failedSetting up service network . . . . . . . . . . . . . . . .failed
 
Old 12-11-2007, 11:32 PM   #2
Tinkster
Moderator
 
Registered: Apr 2002
Location: in a fallen world
Distribution: slackware by choice, others too :} ... android.
Posts: 23,067
Blog Entries: 11

Rep: Reputation: 910Reputation: 910Reputation: 910Reputation: 910Reputation: 910Reputation: 910Reputation: 910Reputation: 910
Hi,

And welcome to LQ!

Can you please post the output of lspci and lsmod here?

And when you were setting up the network printer - what
exactly did you do?


Cheers,
Tink
 
Old 12-12-2007, 03:56 PM   #3
crazylegs
LQ Newbie
 
Registered: Dec 2007
Posts: 4

Original Poster
Rep: Reputation: 0
Network error on bootup

Thanks for replying so rapidily.

Let me give you a little more information. I have a small home based network. I use a Linksys Wireless Router, Linksys 5 port switch, Linksys Printer Server, and a Linksys Cable modem. The router is handling all IP assigments via DHCP. I have assigned the openSuse server a static IP and have modified the /etc/host file and the Windows network host files with all the specific host names and IP addresses. (I am writing some client/server apps and want the Linux box to run all server based apps).

I first tried to install the network printer via the Yast interface. It was unable to resolve the IP address of the Printer Server. So I switched to the KDE Personal Settings / Peripherals / Add Printer dialogs. I used the Administrator Mode option. It resolved the IP address immediately. It asked to test the printer so I did. It sent a file to my Samsung Laser printer which the printer received, but error'd out trying to print. So I canceled the printer setup and went to the Samsung web site, (via the Linux box), to see if they had a more up-to-date driver. The Firefox browser would not navigate to the drivers page successfully so I shut the machine down for the evening. When I started the machine back up it no longer could access the network, period. Not even the Linksys router. I can ping the Linux box host name but cannot get passed the NIC.

Here is the lsmod info:


Module Size Used by

iptable_filter 6912 0

ip_tables 16324 1 iptable_filter

ip6_tables 17476 0

x_tables 18308 2 ip_tables,ip6_tables

snd_pcm_oss 50432 0

snd_mixer_oss 20096 1 snd_pcm_oss

snd_seq_midi 13440 0

snd_seq_midi_event 10880 1 snd_seq_midi

snd_seq 54452 2 snd_seq_midi,snd_seq_midi_event

apparmor 40736 0

loop 21636 0

dm_mod 56880 0

snd_ens1371 29060 1

gameport 18312 1 snd_ens1371

snd_rawmidi 28416 2 snd_seq_midi,snd_ens1371

snd_seq_device 12172 3 snd_seq_midi,snd_seq,snd_rawmidi

snd_ac97_codec 97060 1 snd_ens1371

ac97_bus 6272 1 snd_ac97_codec

snd_pcm 82564 3 snd_pcm_oss,snd_ens1371,snd_ac97_codec

snd_timer 26756 2 snd_seq,snd_pcm

snd 58164 12
snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_seq,snd_ens1371,snd_rawmidi,snd_seq_device,snd_ac97_codec ,snd_pcm,snd_timer

ohci1394 36272 0

i2c_viapro 12436 0

8139too 29184 0

ieee1394 91136 1 ohci1394

via686a 19208 0

hwmon 7300 1 via686a

i2c_isa 8192 1 via686a

shpchp 35092 0

soundcore 11460 1 snd

pci_hotplug 33216 1 shpchp

rtc_cmos 12064 0

parport_pc 40764 0

rtc_core 23048 1 rtc_cmos

rtc_lib 7040 1 rtc_core

i2c_core 27520 3 i2c_viapro,via686a,i2c_isa

snd_page_alloc 14472 1 snd_pcm

mii 9344 1 8139too

amd_k7_agp 12556 1

sr_mod 19492 0

agpgart 35764 1 amd_k7_agp

cdrom 37020 1 sr_mod

parport 37832 1 parport_pc

sg 37036 0

sd_mod 31104 4

uhci_hcd 27024 0

usbcore 123756 2 uhci_hcd

edd 12996 0

ext3 131976 2

mbcache 12292 1 ext3

jbd 68148 1 ext3

pata_via 15620 3

libata 137032 1 pata_via

scsi_mod 140376 4 sr_mod,sg,sd_mod,libata




And here is the lspci data:



00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller (rev 25)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e8005000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at 1490 [disabled] [size=4]
Capabilities: [a0] AGP version 1.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e9000000-e9ffffff
Prefetchable memory behind bridge: f8000000-f9ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:04.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at e8004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 09)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+ <MAbort- >SERR- <PERR-
Latency: 96 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at 1400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at 1480 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1440 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1460 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB12LV23 IEEE-1394 Controller (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Unknown device b11f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e8004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division Unknown device 00d3
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1498 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

01:05.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
Subsystem: nVidia Corporation Unknown device 0017
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f8000000 (32-bit, prefetchable) [size=32M]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>






Hope this is what you were asking for.
Brad
 
Old 12-12-2007, 04:51 PM   #4
crazylegs
LQ Newbie
 
Registered: Dec 2007
Posts: 4

Original Poster
Rep: Reputation: 0
Network Errors on Bootup

Tinkster,


I feel really stupid. I found and fixed the problem. The Linux box is networked through the Linksys Printer Server and this device has a nasty habit of losing it's network connection. To restart it you just unplug the power cable and plug it back in.

Sorry for the trouble and thank you very much for the rapid response.

Brad
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
Two errors on Bootup harley51 Fedora 4 09-11-2006 07:31 PM
Module Errors at Bootup mercuryx013 Slackware 1 03-07-2004 12:21 AM
Errors on bootup? Nikon01 Slackware 5 08-07-2003 02:47 AM
bootup errors N_A_J_M Linux - General 3 08-28-2002 05:58 AM
mounting network interfaces errors during bootup robeb Linux - General 0 07-03-2002 01:47 PM


All times are GMT -5. The time now is 12:45 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration