Need to access files on 2nd SATA hard drive but can't mount
Hello,
I have a system with a single SATA hard drive running Fedora 8 and have installed a 2nd SATA hard drive that was the primary drive in system running Fedora 6. I need to access the files on this 2nd hard drive (/dev/sdb2).
When I attempt to mount the device /dev/sdb2 it will not recognize the filesystem.
I searched through the forums but did not come up with any threads with a similar problem. Can someone help me with this?
Thank you.
Here are some details:
[root@localhost ~]# fdisk -l
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xed5943bb
Device Boot Start End Blocks Id System
/dev/sda1 * 1 25 200781 83 Linux
/dev/sda2 26 19457 156087540 8e Linux LVM
Disk /dev/sdb: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xc7e94dd9
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 13 104391 83 Linux
/dev/sdb2 14 19457 156183930 8e Linux LVM
Disk /dev/dm-0: 157.7 GB, 157705830400 bytes
255 heads, 63 sectors/track, 19173 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/dm-0 doesn't contain a valid partition table
Disk /dev/dm-1: 2080 MB, 2080374784 bytes
255 heads, 63 sectors/track, 252 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x30307800
[root@localhost ~]# cat /etc/fstab
/dev/VolGroup00/LogVol00 / ext3 defaults 1 1
LABEL=/boot /boot ext3 defaults 1 2
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
/dev/VolGroup00/LogVol01 swap swap defaults 0 0
Disk /dev/dm-1 doesn't contain a valid partition table
[root@localhost ~]# pvdisplay
WARNING: Duplicate VG name VolGroup00: Existing R0ox8k-wsTR-jVfz-8y2L-X5QR-K5rd-wDxCxA (created here) takes precedence over SkYedY-zkN4-CwND-w9a3-6e8A-1sqE-olMWP1
--- Physical volume ---
PV Name /dev/sdb2
VG Name VolGroup00
PV Size 148.95 GB / not usable 11.37 MB
Allocatable yes
PE Size (KByte) 32768
Total PE 4766
Free PE 1
Allocated PE 4765
PV UUID 3cjuJe-Lj5Z-H9Cy-pqYg-QDVT-CQ7c-rO8E1V
--- Physical volume ---
PV Name /dev/sda2
VG Name VolGroup00
PV Size 148.86 GB / not usable 13.24 MB
Allocatable yes
PE Size (KByte) 32768
Total PE 4763
Free PE 1
Allocated PE 4762
PV UUID KoQY86-5gJd-BDcz-vwAd-JxOw-NRlh-10Li80
[root@localhost ~]# lvdisplay
WARNING: Duplicate VG name VolGroup00: Existing R0ox8k-wsTR-jVfz-8y2L-X5QR-K5rd-wDxCxA (created here) takes precedence over SkYedY-zkN4-CwND-w9a3-6e8A-1sqE-olMWP1
--- Logical volume ---
LV Name /dev/VolGroup00/LogVol00
VG Name VolGroup00
LV UUID RzFlyf-Cxd5-3g37-xBH3-gcjN-1wo2-VjREZ6
LV Write Access read/write
LV Status available
# open 1
LV Size 146.88 GB
Current LE 4700
Segments 1
Allocation inherit
Read ahead sectors 0
Block device 253:0
--- Logical volume ---
LV Name /dev/VolGroup00/LogVol01
VG Name VolGroup00
LV UUID 2Rr3w7-lEEJ-y5J5-zZWT-j70C-oDIr-J3FBeD
LV Write Access read/write
LV Status available
# open 1
LV Size 1.94 GB
Current LE 62
Segments 1
Allocation inherit
Read ahead sectors 0
Block device 253:1
[root@localhost ~]#
[root@localhost ~]#
[root@localhost ~]# mount /dev/sdb2 /test
mount: you must specify the filesystem type
[root@localhost ~]# mount -t ext3 /dev/sdb2 /test
mount: wrong fs type, bad option, bad superblock on /dev/sdb2,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
[root@localhost ~]# dmesg | tail
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present
[drm] Initialized drm 1.1.0 20060810
PCI: Setting latency timer of device 0000:00:02.0 to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hfs: unable to find HFS+ superblock
VFS: Can't find ext3 filesystem on dev sdb2.
[root@localhost ~]#
|