LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Newbie (http://www.linuxquestions.org/questions/linux-newbie-8/)
-   -   Linux Kernel Panic (http://www.linuxquestions.org/questions/linux-newbie-8/linux-kernel-panic-4175428492/)

Snaidy1 09-22-2012 02:23 AM

Linux Kernel Panic
 
Hello Guyz,
I am little new to Linux,I am using Friendly arm board mini2440
I tried porting Linux V2.6.32.2 in to board(I am trying to boot through NFS root file system created in buildroot) ,but I am getting kernel panic message and Kernel Too old message,the error message what i get is

S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 5275 at 0x000029360000
Bad eraseblock 5277 at 0x0000293a0000
Bad eraseblock 6406 at 0x0000320c0000
Creating 4 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x000000000000-0x000000060000 : "supervivi"
0x000000060000-0x000000260000 : "Kernel"
0x000000260000-0x000040260000 : "root"
mtd: partition "root" extends beyond the end of device "NAND 1GiB 3,3V 8-bit" -0
0x000000000000-0x000040000000 : "nand"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.29.4-FriendlyARM ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
#0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2124-09-21 10:41:02 UTC (58762)
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.1.123, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.123, domain=, nis-domain=(none),
bootserver=192.168.1.122, rootserver=192.168.1.122, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.122
eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
Looking up port of RPC 100005/1 on 192.168.1.122
VFS: Mounted root (nfs filesystem) on device 0:11.
Freeing init memory: 124K
FATAL: kernel too old
Kernel panic - not syncing: Attempted to kill init!



Please help me in how to debug this and resolve kernel panic messages

nileshgr 09-22-2012 03:00 AM

I think this is related to GLibc. Which version of GLibc are you using?

Snaidy1 09-23-2012 12:31 AM

I am using GCC tool chain arm-linux-gcc 4.4.3,I donīt know how to find the Glibc of this,Can u please guide how I can find it.

http://www.friendlyarm.net/dl.php?fi...-gcc-4.4.3.tgz
Thank u in advance


All times are GMT -5. The time now is 11:07 PM.