installing usb intellimouse problems
 

I'm trying to install a microsoft usb intellimouse and have followed every link to have this done and actually go it working for one session, but now it simply does not lit again... I did disable plug&play from the bios and that seemed to work at that time but now I get the same problem:

[root@enrique ~]# dmesg | grep usb
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 13:44:31 Sep 4 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb-uhci.c: USB UHCI at I/O 0x1840, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb.c: failed to set device 3 default configuration (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=4 (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=5 (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=6 (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=7 (error=-110)


I did change my XF86Config file to:

...
Section "ServerLayout"
#
Identifier "Anaconda Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Mouse1" "AlwaysCore"
InputDevice "Keyboard0" "CoreKeyboard"

...
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "GlidePointPS/2"
Option "Device" "/dev/psaux"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection

Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mouse0"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "no"
EndSection
...

The mouse works on MS. Let me know if more information would be required... I appreciate your knowledge.

Tks!
Enrique

Why do you have two mouse sections? Try removing all of these:

I have two because I would like to have the external mouse and the built-in mouse to use at the same time... but the problem I think is that it's that the usb mouse in not being recognized... don't know if this would have to do anything with IRQ or something else????

OK... so is the intellimouse mouse0 or mouse1?

I read that you could have both of them working using...

InputDevice "Mouse0" "CorePointer"
InputDevice "Mouse1" "AlwaysCore"

but still... mouse1 is not even being detected... I could try to comment mouse0 but I don't think this will do the trick since mouse1 is not even being detected...

usb.c: failed to set device 3 default configuration (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=4 (error=-110)
usb_control/bulk_msg: timeout

sorry the intellimouse was supposed to be:

Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mouse0"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "no"
EndSection

Hmm... after re-reading your posts, it's obviously got something to do with USB HID support on your system (probably kernel-level).

I'm sorry I can't you more with this... perhaps you could ask in the Hardware forum here?

ok.... tks! should i open a new thread in the hardware forum? I'm sorry but i'm new at linuxquestions.org