LinuxQuestions.org
Page 1 of 3 1 23
Show 50 post(s) from this thread on one page

LinuxQuestions.org (/questions/)
-   Linux - Newbie (https://www.linuxquestions.org/questions/linux-newbie-8/)
-   -   Hardware or Software? (https://www.linuxquestions.org/questions/linux-newbie-8/hardware-or-software-4175581237/)

skippy1729 06-02-2016 12:25 AM
Hardware or Software?
 
Not even sure if this is a hardware or software problem. Have eliminated memory, hard drive, power supply and monitor as a potential source. Nothing is overheating and crashes can occur from a cold start or hours later. Same problems using the onboard video or a Nvidia GT430.

Symptom: Occasional system freezing with or without screen going to a colorful series of diagonal lines. Have tried fresh installations of Ubuntu 14.04LTS, 16.04LTS and Slackware 14.1. Verified hashes on all downloads.

Google Chrome will always crash Ubuntu immediately. Firefox will run most of the time. The default Ubuntu video player will always crash immediately. VLC video player always works.

Firefox will always crash Slackware immediately. SeaMonkey will run.

Possibilities:

1. Defective CPU. Any suggested test programs for functionality? I am not doing any kind of overclocking.

2. Defective Motherboard?

3. Linux incompatible motherboard? I am using ASROCK N68-GS64/USB3 FX.

4. Other????

I have toyed with the idea of installing Windows. I still have a copy of 98 but is there anything I could try first? I suppose it would eliminate options 1 and 2 but not 3 or 4.

:banghead:

astrogeek 06-02-2016 12:49 AM
With two distros and 3 versions of GNU/Linux, I don't see where loading another OS would be of any help.

It is probably less important which applications cause the crash, differences among distros only suggesting different memory or register mappings which trigger the fault.

You don't say if there is anything in the logs, but from the description my initial feeling is that it doesn't matter much.

I would still bet on memory as first likely cause. You say that you have eliminated memory, but you don't say how you elimintated it. So I'd revisit that and make sure that you have eliminated it with certainty. You also don't say how much memory you have so that number would be a comfort factor...

Next, motherboard... bad solder, socket, trace, component, who knows! But my own experience says that motherboard is the next suspect on the list. Have you tried poking around on the board (gently, with a non-conductive poking device) to see if there is any correlation with physical stresses. If there is, can you localize it?

Power supply is next, how did you eliminate that? Swap it out?

CPU... maybe, but if it boots at all is not overclocked, I tend to think it is OK - but my experience ends with 4 cores and a few years back, so current CPUs... don't have that feel yet. That said, check seating/socket, heat sink and grease, hot spots.

skippy1729 06-02-2016 01:08 AM
Quote:
Originally Posted by astrogeek (Post 5554388)
With two distros and 3 versions of GNU/Linux, I don't see where loading another OS would be of any help.

It is probably less important which applications cause the crash, differences among distros only suggesting different memory or register mappings which trigger the fault.

You don't say if there is anything in the logs, but from the description my initial feeling is that it doesn't matter much.

I would still bet on memory as first likely cause. You say that you have eliminated memory, but you don't say how you elimintated it. So I'd revisit that and make sure that you have eliminated it with certainty. You also don't say how much memory you have so that number would be a comfort factor...

Next, motherboard... bad solder, socket, trace, component, who knows! But my own experience says that motherboard is the next suspect on the list. Have you tried poking around on the board (gently, with a non-conductive poking device) to see if there is any correlation with physical stresses. If there is, can you localize it?

Power supply is next, how did you eliminate that? Swap it out?


CPU... maybe, but if it boots at all is not overclocked, I tend to think it is OK - but my experience ends with 4 cores and a few years back, so current CPUs... don't have that feel yet. That said, check seating/socket, heat sink and grease, hot spots.
Ran memtest86 for about a day with 4 clean passes. 2G of DDR3.

The BIOS shows temps of about 35 C on the cpu.

Swapped out power supplies which are both about twice as big as necessary. Tried two different HDs one IDE and one SATA and checked both with badblocks.

I'll give the motherboard a good look soon.

astrogeek 06-02-2016 01:35 AM
Quote:
Originally Posted by skippy1729 (Post 5554394)
Ran memtest86 for about a day with 4 clean passes. 2G of DDR3.
...
I'll give the motherboard a good look soon.
That is a pretty good memory test, although there are still real world runtime differences.

I would suggest doing memtest again, and do the poking around on the motherboard, and the memory modules, while running memtest. I find that to be a test environment!

pan64 06-02-2016 05:02 AM
I bet on RAM too. Just in case if you can replace RAM or remove half of it.
You missed the possibility of defective GPU, try to use a(nother) graphic card.

beachboy2 06-02-2016 05:04 AM
skippy1729,

I had problems with Crucial memory on a custom-built desktop PC running W7.

It is the only occasion that I have ever had faulty RAM from Crucial and they replaced it without a quibble.

I ran memtest86 twice and no fault was found.

I put both original modules back in place, started up and the problem was still there.

I then used the Windows Memory Diagnostic Tool and it diagnosed that one of the two modules was faulty within a few minutes.

http://windows.microsoft.com/en-gb/w...-your-computer

sundialsvcs 06-02-2016 07:11 AM
Since the symptoms you describe are visual, and the system environment remains intact (although programs are crashing), this is probably a software problem, related to XWindows/XOrg, a video driver, configuration and so-forth.

The usual "question #1": when did these symptoms start, and what happened immediately before then?

Emerson 06-02-2016 07:46 AM
Can you pastebin full dmesg?

keefaz 06-02-2016 07:47 AM
Tried BIOS parameters reset?
What are the processor specs?
(seems compatible with processors having 95W TDP max)
http://www.asrock.com/mb/NVIDIA/N68-Gs/

skippy1729 06-02-2016 09:08 AM
Thanks for the interest. I'll try to answer all the points you've raised so far:

1. Problems started on day one of putting this box together.

2. Removed the GPU, same problem with the onboard video.

3. Processor is a quad core low power Athlon (45 watt).

4. CPU and memory were from a previous box that ran OK for 3 or 4 years.

5. Crashes do not always involve video. Occasional system freezes.

6. I'll post the output of dmesg in my next post. It's all Greek to me.

7. Will try removing the memory sticks one at a time.

8. Can you be more specific about what to try with the BIOS?

skippy1729 06-02-2016 09:16 AM
OUTPUT OF dmesg: PART 1

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.17 (root@hive64) (gcc version 4.8.2 (GCC) ) #2 SMP Wed Oct 23 16:34:38 CDT 2013
[ 0.000000] Command line: BOOT_IMAGE=Linux ro root=802 vt.default_utf8=0
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff9ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bffa0000-0x00000000bffaffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000bffb0000-0x00000000bffdffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bffe0000-0x00000000bfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./N68-GS4/USB3 FX, BIOS P1.10 10/02/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000130000000 aka 4864M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xbffa0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x0236f000, 0x0236ffff] PGTABLE
[ 0.000000] BRK [0x02370000, 0x02370fff] PGTABLE
[ 0.000000] BRK [0x02371000, 0x02371fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x12fe00000-0x12fffffff]
[ 0.000000] [mem 0x12fe00000-0x12fffffff] page 2M
[ 0.000000] BRK [0x02372000, 0x02372fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x12c000000-0x12fdfffff]
[ 0.000000] [mem 0x12c000000-0x12fdfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x12bffffff]
[ 0.000000] [mem 0x100000000-0x12bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xbff9ffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0xbfdfffff] page 2M
[ 0.000000] [mem 0xbfe00000-0xbff9ffff] page 4k
[ 0.000000] ACPI: RSDP 00000000000fad80 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 00000000bffa0000 0003C (v01 100214 RSDT1428 20141002 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000bffa0200 00084 (v01 A_M_I OEMFACP 12000601 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000bffa0470 04FF9 (v01 A1044 A1044101 00000101 INTL 20051117)
[ 0.000000] ACPI: FACS 00000000bffb0000 00040
[ 0.000000] ACPI: APIC 00000000bffa0390 000A0 (v01 100214 APIC1428 20141002 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000bffa0430 0003C (v01 100214 OEMMCFG 20141002 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000bffb0040 00072 (v01 100214 OEMB1428 20141002 MSFT 00000097)
[ 0.000000] ACPI: AAFT 00000000bffaa470 0002E (v01 100214 OEMAAFT 20141002 MSFT 00000097)
[ 0.000000] ACPI: SSDT 00000000bffaa4a0 008BC (v01 A M I POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012ba00000-ffff88012f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x12fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xbff9ffff]
[ 0.000000] node 0: [mem 0x100000000-0x12fffffff]
[ 0.000000] On node 0 totalpages: 982846
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12223 pages used for memmap
[ 0.000000] DMA32 zone: 782240 pages, LIFO batch:31
[ 0.000000] Normal zone: 3072 pages used for memmap
[ 0.000000] Normal zone: 196608 pages, LIFO batch:31
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x508
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bffa0000 - 00000000bffb0000
[ 0.000000] PM: Registered nosave memory: 00000000bffb0000 - 00000000bffe0000
[ 0.000000] PM: Registered nosave memory: 00000000bffe0000 - 00000000c0000000
[ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fef00000
[ 0.000000] PM: Registered nosave memory: 00000000fef00000 - 00000000fff00000
[ 0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[ 0.000000] e820: [mem 0xc0000000-0xfebfffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88012fc00000 s79424 r8192 d22976 u262144
[ 0.000000] pcpu-alloc: s79424 r8192 d22976 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 967466
[ 0.000000] Kernel command line: BOOT_IMAGE=Linux ro root=802 vt.default_utf8=0
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Node 0: aperture @ 0 size 32 MB
[ 0.000000] Your BIOS doesn't leave a aperture memory hole
[ 0.000000] Please enable the IOMMU option in the BIOS setup
[ 0.000000] This costs you 64 MB of RAM
[ 0.000000] Mapping aperture over 65536 KB of RAM @ b4000000
[ 0.000000] PM: Registered nosave memory: 00000000b4000000 - 00000000b8000000
[ 0.000000] Memory: 3711084k/4980736k available (11725k kernel code, 1049352k absent, 220300k reserved, 5712k data, 1272k init)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] NR_IRQS:8448 nr_irqs:744 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 2209.984 MHz processor
[ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4419.96 BogoMIPS (lpj=2209984)
[ 0.000262] pid_max: default: 32768 minimum: 301
[ 0.000432] Security Framework initialized
[ 0.000569] Mount-cache hash table entries: 256
[ 0.000889] Initializing cgroup subsys devices
[ 0.001019] Initializing cgroup subsys freezer
[ 0.001148] Initializing cgroup subsys net_cls
[ 0.001276] Initializing cgroup subsys blkio
[ 0.001416] Initializing cgroup subsys perf_event
[ 0.001565] tseg: 0000000000
[ 0.001571] CPU: Physical Processor ID: 0
[ 0.001699] CPU: Processor Core ID: 0
[ 0.001826] mce: CPU supports 6 MCE banks
[ 0.001959] LVT offset 0 assigned for vector 0xf9
[ 0.002090] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
[ 0.002090] Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64
[ 0.002090] tlb_flushall_shift: 4
[ 0.002529] Freeing SMP alternatives: 36k freed
[ 0.002668] ACPI: Core revision 20130328
[ 0.005319] ACPI: All ACPI Tables successfully acquired
[ 0.005883] ftrace: allocating 36377 entries in 143 pages
[ 0.024301] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.034437] smpboot: CPU0: AMD Athlon(tm) II X4 600e Processor (fam: 10, model: 05, stepping: 02)
[ 0.136215] Performance Events: AMD PMU driver.
[ 0.136368] ... version: 0
[ 0.136495] ... bit width: 48
[ 0.136622] ... generic registers: 4
[ 0.136750] ... value mask: 0000ffffffffffff
[ 0.136880] ... max period: 00007fffffffffff
[ 0.137008] ... fixed-purpose events: 0
[ 0.137136] ... event mask: 000000000000000f
[ 0.137438] MCE: In-kernel MCE decoding enabled.
[ 0.137653] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.177215] Brought up 4 CPUs
[ 0.177464] smpboot: Total of 4 processors activated (17679.87 BogoMIPS)
[ 0.178418] devtmpfs: initialized
[ 0.180245] PM: Registering ACPI NVS region [mem 0xbffb0000-0xbffdffff] (196608 bytes)
[ 0.180759] xor: measuring software checksum speed
[ 0.190170] prefetch64-sse: 8364.000 MB/sec
[ 0.200161] generic_sse: 8136.000 MB/sec
[ 0.200289] xor: using function: prefetch64-sse (8364.000 MB/sec)
[ 0.200422] atomic64 test passed for x86-64 platform with CX8 and with SSE
[ 0.200621] regulator-dummy: no parameters
[ 0.200807] NET: Registered protocol family 16
[ 0.201019] node 0 link 0: io port [1000, ffffff]
[ 0.201021] TOM: 00000000d0000000 aka 3328M
[ 0.201151] node 0 link 0: mmio [f0000000, f7ffffff]
[ 0.201157] node 0 link 0: mmio [d0000000, efffffff]
[ 0.201159] node 0 link 0: mmio [f8000000, fe0bffff]
[ 0.201161] node 0 link 0: mmio [a0000, bffff]
[ 0.201163] TOM2: 0000000130000000 aka 4864M
[ 0.201292] bus: [bus 00-1f] on node 0 link 0
[ 0.201294] bus: 00 [io 0x0000-0xffff]
[ 0.201295] bus: 00 [mem 0xd0000000-0xffffffff]
[ 0.201297] bus: 00 [mem 0x000a0000-0x000bffff]
[ 0.201298] bus: 00 [mem 0x130000000-0xfcffffffff]
[ 0.201336] ACPI: bus type PCI registered
[ 0.201464] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.201654] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[ 0.201894] PCI: not using MMCONFIG
[ 0.202022] PCI: Using configuration type 1 for base access
[ 0.202155] PCI: Using configuration type 1 for extended access
[ 0.205698] bio: create slab <bio-0> at 0
[ 0.222152] raid6: sse2x1 3117 MB/s
[ 0.239142] raid6: sse2x2 4812 MB/s
[ 0.256118] raid6: sse2x4 5718 MB/s
[ 0.256246] raid6: using algorithm sse2x4 (5718 MB/s)
[ 0.256375] raid6: using intx1 recovery algorithm
[ 0.256587] ACPI: Added _OSI(Module Device)
[ 0.256715] ACPI: Added _OSI(Processor Device)
[ 0.256844] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.256974] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.257871] ACPI: EC: Look up EC in DSDT
[ 0.258740] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.260913] ACPI: Interpreter enabled
[ 0.261051] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130328/hwxface-568)
[ 0.261340] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.261468] ACPI: Using IOAPIC for interrupt routing
[ 0.261616] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[ 0.262721] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in ACPI motherboard resources
[ 0.270606] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.270928] ACPI: No dock devices found.
[ 0.277783] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.278156] acpi PNP0A03:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-7f] only partially covers this bridge
[ 0.278467] PCI host bridge to bus 0000:00
[ 0.278597] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.278727] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.278858] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.278993] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.279125] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
[ 0.279257] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
[ 0.279389] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfebfffff]
[ 0.279541] pci 0000:00:00.0: [10de:03e2] type 00 class 0x050000
[ 0.279750] pci 0000:00:01.0: [10de:03e1] type 00 class 0x060100
[ 0.279757] pci 0000:00:01.0: reg 10: [io 0x0900-0x09ff]
[ 0.279831] pci 0000:00:01.1: [10de:03eb] type 00 class 0x0c0500
[ 0.279842] pci 0000:00:01.1: reg 10: [io 0x0e00-0x0e3f]
[ 0.279857] pci 0000:00:01.1: reg 20: [io 0x0600-0x063f]
[ 0.279862] pci 0000:00:01.1: reg 24: [io 0x0700-0x073f]
[ 0.279889] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.279925] pci 0000:00:01.1: System wakeup disabled by ACPI
[ 0.280083] pci 0000:00:01.2: [10de:03f5] type 00 class 0x050000
[ 0.280165] pci 0000:00:02.0: [10de:03f1] type 00 class 0x0c0310
[ 0.280174] pci 0000:00:02.0: reg 10: [mem 0xefeff000-0xefefffff]
[ 0.280206] pci 0000:00:02.0: supports D1 D2
[ 0.280208] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.280236] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 0.280393] pci 0000:00:02.1: [10de:03f2] type 00 class 0x0c0320
[ 0.280403] pci 0000:00:02.1: reg 10: [mem 0xefefec00-0xefefecff]
[ 0.280442] pci 0000:00:02.1: supports D1 D2
[ 0.280444] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.280474] pci 0000:00:02.1: System wakeup disabled by ACPI
[ 0.280635] pci 0000:00:04.0: [10de:03f3] type 01 class 0x060401
[ 0.280689] pci 0000:00:04.0: System wakeup disabled by ACPI
[ 0.280847] pci 0000:00:05.0: [10de:03f0] type 00 class 0x040300
[ 0.280858] pci 0000:00:05.0: reg 10: [mem 0xefef8000-0xefefbfff]
[ 0.280898] pci 0000:00:05.0: PME# supported from D3hot D3cold
[ 0.280929] pci 0000:00:05.0: System wakeup disabled by ACPI
[ 0.281094] pci 0000:00:06.0: [10de:03ec] type 00 class 0x01018a
[ 0.281115] pci 0000:00:06.0: reg 20: [io 0xffa0-0xffaf]
[ 0.281183] pci 0000:00:07.0: [10de:03ef] type 00 class 0x068000
[ 0.281192] pci 0000:00:07.0: reg 10: [mem 0xefefd000-0xefefdfff]
[ 0.281196] pci 0000:00:07.0: reg 14: [io 0xe080-0xe087]
[ 0.281229] pci 0000:00:07.0: supports D1 D2
[ 0.281231] pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.281262] pci 0000:00:07.0: System wakeup disabled by ACPI
[ 0.281417] pci 0000:00:08.0: [10de:03f6] type 00 class 0x010185
[ 0.281425] pci 0000:00:08.0: reg 10: [io 0xe000-0xe007]
[ 0.281429] pci 0000:00:08.0: reg 14: [io 0xdc00-0xdc03]
[ 0.281433] pci 0000:00:08.0: reg 18: [io 0xd880-0xd887]
[ 0.281437] pci 0000:00:08.0: reg 1c: [io 0xd800-0xd803]
[ 0.281442] pci 0000:00:08.0: reg 20: [io 0xd480-0xd48f]
[ 0.281446] pci 0000:00:08.0: reg 24: [mem 0xefefc000-0xefefcfff]
[ 0.281508] pci 0000:00:08.1: [10de:03f6] type 00 class 0x010185
[ 0.281516] pci 0000:00:08.1: reg 10: [io 0xd400-0xd407]
[ 0.281520] pci 0000:00:08.1: reg 14: [io 0xd080-0xd083]
[ 0.281524] pci 0000:00:08.1: reg 18: [io 0xd000-0xd007]
[ 0.281528] pci 0000:00:08.1: reg 1c: [io 0xcc00-0xcc03]
[ 0.281533] pci 0000:00:08.1: reg 20: [io 0xc880-0xc88f]
[ 0.281537] pci 0000:00:08.1: reg 24: [mem 0xefef7000-0xefef7fff]
[ 0.281605] pci 0000:00:09.0: [10de:03e8] type 01 class 0x060400
[ 0.281631] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.281662] pci 0000:00:09.0: System wakeup disabled by ACPI
[ 0.281820] pci 0000:00:0b.0: [10de:03e9] type 01 class 0x060400
[ 0.281845] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.281874] pci 0000:00:0b.0: System wakeup disabled by ACPI
[ 0.282034] pci 0000:00:0c.0: [10de:03e9] type 01 class 0x060400
[ 0.282059] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.282092] pci 0000:00:0c.0: System wakeup disabled by ACPI
[ 0.282248] pci 0000:00:0d.0: [10de:03d6] type 00 class 0x030000
[ 0.282255] pci 0000:00:0d.0: reg 10: [mem 0xee000000-0xeeffffff]
[ 0.282260] pci 0000:00:0d.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.282266] pci 0000:00:0d.0: reg 1c: [mem 0xed000000-0xedffffff 64bit]
[ 0.282271] pci 0000:00:0d.0: reg 30: [mem 0xefec0000-0xefedffff pref]
[ 0.282334] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[ 0.282388] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[ 0.282438] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[ 0.282487] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[ 0.282539] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[ 0.282643] pci 0000:00:04.0: PCI bridge to [bus 01] (subtractive decode)
[ 0.282777] pci 0000:00:04.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.282780] pci 0000:00:04.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.282782] pci 0000:00:04.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.282784] pci 0000:00:04.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.282786] pci 0000:00:04.0: bridge window [mem 0xd0000000-0xefffffff] (subtractive decode)
[ 0.282788] pci 0000:00:04.0: bridge window [mem 0xf8000000-0xfebfffff] (subtractive decode)
[ 0.282824] pci 0000:00:09.0: PCI bridge to [bus 02]
[ 0.282990] pci 0000:00:0b.0: PCI bridge to [bus 03]
[ 0.283168] pci 0000:04:00.0: [1b6f:7052] type 00 class 0x0c0330
[ 0.283190] pci 0000:04:00.0: reg 10: [mem 0xefff8000-0xefffffff 64bit]
[ 0.283290] pci 0000:04:00.0: supports D1 D2
[ 0.283292] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.285950] pci 0000:00:0c.0: PCI bridge to [bus 04]
[ 0.286090] pci 0000:00:0c.0: bridge window [mem 0xeff00000-0xefffffff]
[ 0.286102] pci_bus 0000:00: on NUMA node 0
[ 0.286239] acpi PNP0A03:00: Requesting ACPI _OSC control (0x1d)
[ 0.286599] acpi PNP0A03:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x0c
[ 0.286834] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.287677] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.288065] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 0.288449] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.288831] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.289217] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *10
[ 0.289577] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
[ 0.289961] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
[ 0.290342] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
[ 0.290726] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
[ 0.291091] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 0.291453] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *10
[ 0.291815] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
[ 0.292179] ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *10
[ 0.292541] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
[ 0.292901] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
[ 0.293288] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 0.293649] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *5
[ 0.294050] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.294428] ACPI: Enabled 1 GPEs in block 00 to 1F
[ 0.294602] acpi root: \_SB_.PCI0 notify handler is installed
[ 0.294632] Found 1 acpi root devices
[ 0.294740] vgaarb: device added: PCI:0000:00:0d.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.294978] vgaarb: loaded
[ 0.295105] vgaarb: bridge control possible 0000:00:0d.0
[ 0.295302] SCSI subsystem initialized
[ 0.295430] ACPI: bus type ATA registered
[ 0.295645] libata version 3.00 loaded.
[ 0.295649] ACPI: bus type USB registered

skippy1729 06-02-2016 09:18 AM
OUTPUT OF dmesg: 2nd part

[ 0.295798] usbcore: registered new interface driver usbfs
[ 0.295938] usbcore: registered new interface driver hub
[ 0.296141] usbcore: registered new device driver usb
[ 0.296364] PCI: Using ACPI for IRQ routing
[ 0.299466] PCI: pci_cache_line_size set to 64 bytes
[ 0.299500] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[ 0.299503] e820: reserve RAM buffer [mem 0xbffa0000-0xbfffffff]
[ 0.299635] Switching to clocksource refined-jiffies
[ 0.304615] pnp: PnP ACPI init
[ 0.304759] ACPI: bus type PNP registered
[ 0.304953] pnp 00:00: [dma 4]
[ 0.304977] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.304998] pnp 00:01: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.305030] pnp 00:02: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.305436] pnp 00:03: [dma 3]
[ 0.305543] pnp 00:03: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.305996] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.306129] system 00:04: [io 0x0500-0x057f] has been reserved
[ 0.306260] system 00:04: [io 0x0580-0x05ff] has been reserved
[ 0.306392] system 00:04: [io 0x0800-0x087f] has been reserved
[ 0.306522] system 00:04: [io 0x0880-0x08ff] has been reserved
[ 0.306653] system 00:04: [io 0x0d00-0x0d7f] has been reserved
[ 0.306784] system 00:04: [io 0x0d80-0x0dff] has been reserved
[ 0.306917] system 00:04: [io 0x1100-0x117f] has been reserved
[ 0.307048] system 00:04: [io 0x1180-0x11ff] has been reserved
[ 0.307180] system 00:04: [mem 0x000d0000-0x000d3fff window] has been reserved
[ 0.307416] system 00:04: [mem 0x000d4000-0x000d7fff window] has been reserved
[ 0.307651] system 00:04: [mem 0x000de000-0x000dffff window] has been reserved
[ 0.307885] system 00:04: [mem 0xfec80000-0xfecfffff] has been reserved
[ 0.308020] system 00:04: [mem 0xfefe0000-0xfefe01ff] has been reserved
[ 0.308152] system 00:04: [mem 0xfefe1000-0xfefe1fff] has been reserved
[ 0.308284] system 00:04: [mem 0xfee01000-0xfeefffff] has been reserved
[ 0.308417] system 00:04: [mem 0xffb80000-0xffffffff] could not be reserved
[ 0.308550] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.308714] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.308810] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.308945] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.309077] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.309133] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.309194] pnp 00:08: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[ 0.309396] pnp 00:09: [dma 0 disabled]
[ 0.309444] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.309520] system 00:0a: [io 0x0290-0x029f] has been reserved
[ 0.309651] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.309712] system 00:0b: [mem 0xf0000000-0xf7ffffff] has been reserved
[ 0.309844] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.310059] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.310191] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.310324] system 00:0c: [mem 0x00100000-0xcfffffff] could not be reserved
[ 0.310456] system 00:0c: [mem 0xfec00000-0xffffffff] could not be reserved
[ 0.310589] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.310837] pnp: PnP ACPI: found 13 devices
[ 0.310968] ACPI: bus type PNP unregistered
[ 0.316992] Switching to clocksource acpi_pm
[ 0.317168] pci 0000:00:04.0: PCI bridge to [bus 01]
[ 0.317302] pci 0000:00:09.0: PCI bridge to [bus 02]
[ 0.317434] pci 0000:00:0b.0: PCI bridge to [bus 03]
[ 0.317566] pci 0000:00:0c.0: PCI bridge to [bus 04]
[ 0.317700] pci 0000:00:0c.0: bridge window [mem 0xeff00000-0xefffffff]
[ 0.317843] pci 0000:00:04.0: setting latency timer to 64
[ 0.317850] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.317852] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.317854] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.317856] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.317858] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xefffffff]
[ 0.317860] pci_bus 0000:00: resource 9 [mem 0xf8000000-0xfebfffff]
[ 0.317863] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 0.317865] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 0.317867] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.317869] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.317871] pci_bus 0000:01: resource 8 [mem 0xd0000000-0xefffffff]
[ 0.317873] pci_bus 0000:01: resource 9 [mem 0xf8000000-0xfebfffff]
[ 0.317875] pci_bus 0000:04: resource 1 [mem 0xeff00000-0xefffffff]
[ 0.317923] NET: Registered protocol family 2
[ 0.318221] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.318623] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.318907] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.319082] TCP: reno registered
[ 0.319237] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.319392] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.319627] NET: Registered protocol family 1
[ 0.319882] RPC: Registered named UNIX socket transport module.
[ 0.320012] RPC: Registered udp transport module.
[ 0.320140] RPC: Registered tcp transport module.
[ 0.320279] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.320689] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 0.393422] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[ 0.393671] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.393845] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394029] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394220] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394401] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394588] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394776] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.394968] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.395110] pci 0000:00:0d.0: Boot video device
[ 0.395302] ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 19
[ 0.395506] PCI: CLS 64 bytes, default 64
[ 0.395553] PCI-DMA: Disabling AGP.
[ 0.395772] PCI-DMA: aperture base @ b4000000 size 65536 KB
[ 0.395901] PCI-DMA: using GART IOMMU.
[ 0.396029] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 0.399781] LVT offset 1 assigned for vector 0x400
[ 0.399921] Failed to setup IBS LVT offset, IBSCTL = 0xffffffff
[ 0.399923] [Firmware Bug]: cpu 3, try to use APIC500 (LVT offset 0) for vector 0x10400, but the register is already in use for vector 0xf9 on another cpu
[ 0.400182] [Firmware Bug]: cpu 3, IBS interrupt offset 0 not available (MSRC001103A=0x0000000000000100)
[ 0.400425] Failed to setup IBS, -22
[ 0.401380] audit: initializing netlink socket (disabled)
[ 0.401526] type=2000 audit(1464875487.293:1): initialized
[ 0.403252] VFS: Disk quotas dquot_6.5.2
[ 0.403431] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.404174] NFS: Registering the id_resolver key type
[ 0.404311] Key type id_resolver registered
[ 0.404439] Key type id_legacy registered
[ 0.404571] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.404774] NTFS driver 2.1.30 [Flags: R/W].
[ 0.404948] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.405169] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.407138] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 0.407788] OCFS2 1.5.0
[ 0.408035] ocfs2: Registered cluster interface o2cb
[ 0.408182] OCFS2 DLMFS 1.5.0
[ 0.408373] OCFS2 User DLM kernel interface loaded
[ 0.408506] OCFS2 Node Manager 1.5.0
[ 0.408718] OCFS2 DLM 1.5.0
[ 0.408967] bio: create slab <bio-1> at 1
[ 0.409292] Btrfs loaded
[ 0.409425] msgmni has been set to 7377
[ 0.411289] async_tx: api initialized (async)
[ 0.411449] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.411745] io scheduler noop registered
[ 0.411874] io scheduler deadline registered
[ 0.412006] io scheduler cfq registered (default)
[ 0.412236] pcieport 0000:00:09.0: irq 40 for MSI/MSI-X
[ 0.412276] pcieport 0000:00:0b.0: irq 41 for MSI/MSI-X
[ 0.412310] pcieport 0000:00:0c.0: irq 42 for MSI/MSI-X
[ 0.412362] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.412578] GHES: HEST is not enabled!
[ 0.414390] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.435023] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.436046] Floppy drive(s): fd0 is 1.44M
[ 0.437045] brd: module loaded
[ 0.437198] Compaq SMART2 Driver (v 2.6.0)
[ 0.437348] HP CISS Driver (v 3.6.26)
[ 0.438051] fnic: Cisco FCoE HBA Driver, ver 1.5.0.22
[ 0.438231] fnic: Successfully Initialized Trace Buffer
[ 0.438580] Adaptec aacraid driver 1.2-0[30200]-ms
[ 0.438767] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 0.439021] scsi: <fdomain> Detection failed (no card)
[ 0.439182] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.05.00.03-k.
[ 0.439427] Emulex LightPulse Fibre Channel SCSI driver 8.3.39
[ 0.439557] Copyright(c) 2004-2009 Emulex. All rights reserved.
[ 0.442140] Brocade BFA FC/FCOE SCSI driver - version: 3.1.2.1
[ 0.442326] DC390: clustering now enabled by default. If you get problems load
[ 0.442561] with "disable_clustering=1" and report to maintainers
[ 0.442702] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 0.442989] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 0.443147] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[ 0.443293] mpt2sas version 14.100.00.00 loaded
[ 0.443491] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 0.443644] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 0.443784] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 0.444030] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
[ 0.444289] ipr: IBM Power RAID SCSI Device Driver version: 2.6.0 (November 16, 2012)
[ 0.444535] RocketRAID 3xxx/4xxx Controller driver v1.8
[ 0.444673] stex: Promise SuperTrak EX Driver version: 4.6.0000.4
[ 0.444847] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 0.445153] sata_nv 0000:00:08.0: version 3.5
[ 0.445400] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[ 0.445575] sata_nv 0000:00:08.0: setting latency timer to 64
[ 0.445806] scsi0 : sata_nv
[ 0.446025] scsi1 : sata_nv
[ 0.446231] ata1: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd480 irq 21
[ 0.446363] ata2: SATA max UDMA/133 cmd 0xd880 ctl 0xd800 bmdma 0xd488 irq 21
[ 0.446711] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[ 0.446871] sata_nv 0000:00:08.1: setting latency timer to 64
[ 0.447043] scsi2 : sata_nv
[ 0.447300] scsi3 : sata_nv
[ 0.447474] ata3: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xc880 irq 20
[ 0.447606] ata4: SATA max UDMA/133 cmd 0xd000 ctl 0xcc00 bmdma 0xc888 irq 20
[ 0.447865] pata_amd 0000:00:06.0: version 0.4.1
[ 0.447886] pata_amd 0000:00:06.0: setting latency timer to 64
[ 0.448129] scsi4 : pata_amd
[ 0.448749] scsi5 : pata_amd
[ 0.449118] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.449251] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.449859] I2O subsystem v1.325
[ 0.449986] i2o: max drivers = 8
[ 0.450238] I2O Configuration OSM v1.323
[ 0.450369] I2O Bus Adapter OSM v1.317
[ 0.450500] I2O Block Device OSM v1.325
[ 0.450723] I2O SCSI Peripheral OSM v1.316
[ 0.450857] I2O ProcFS OSM v1.316
[ 0.450993] Fusion MPT base driver 3.04.20
[ 0.451130] Copyright (c) 1999-2008 LSI Corporation
[ 0.451261] Fusion MPT SPI Host driver 3.04.20
[ 0.451402] Fusion MPT FC Host driver 3.04.20
[ 0.451545] Fusion MPT SAS Host driver 3.04.20
[ 0.451687] Fusion MPT misc device (ioctl) driver 3.04.20
[ 0.451875] mptctl: Registered with Fusion MPT base driver
[ 0.452005] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 0.452145] Fusion MPT LAN driver 3.04.20
[ 0.452382] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.455913] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.456060] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.456342] mousedev: PS/2 mouse device common for all mice
[ 0.456525] rtc_cmos 00:05: RTC can wake from S4
[ 0.456824] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.456986] rtc_cmos 00:05: alarms up to one year, y3k, 114 bytes nvram
[ 0.457139] md: linear personality registered for level -1
[ 0.457270] md: raid0 personality registered for level 0
[ 0.457400] md: raid1 personality registered for level 1
[ 0.457529] md: raid10 personality registered for level 10
[ 0.457659] md: raid6 personality registered for level 6
[ 0.457788] md: raid5 personality registered for level 5
[ 0.457917] md: raid4 personality registered for level 4
[ 0.458054] md: multipath personality registered for level -4
[ 0.458249] device-mapper: uevent: version 1.0.3
[ 0.458459] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.458752] cpuidle: using governor ladder
[ 0.458880] cpuidle: using governor menu
[ 0.459057] input: Speakup as /devices/virtual/input/input0
[ 0.459260] initialized device: /dev/synth, node (MAJOR 10, MINOR 25)
[ 0.459446] speakup 3.1.6: initialized
[ 0.459580] synth name on entry is: (null)
[ 0.459787] TCP: cubic registered
[ 0.459916] Initializing XFRM netlink socket
[ 0.460056] NET: Registered protocol family 17
[ 0.460219] Key type dns_resolver registered
[ 0.476433] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 0.606416] ata5.00: ATA-6: WDC WD800JB-00JJC0, 05.01C05, max UDMA/100
[ 0.606554] ata5.00: 156301488 sectors, multi 16: LBA
[ 0.606949] ata5.01: ATA-5: MAXTOR 6L060L3, A93.0500, max UDMA/133
[ 0.607082] ata5.01: 117266688 sectors, multi 16: LBA
[ 0.607218] ata5: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c70000) ACPI=0x3f01f (20:15:0x15)
[ 0.607221] ata5: nv_mode_filter: 0x7f39f&0x7f39f->0x7f39f, BIOS=0x7f000 (0xc6c70000) ACPI=0x7f01f (20:15:0x15)
[ 0.610329] ata5.00: configured for UDMA/100
[ 0.616392] ata5.01: configured for UDMA/133
[ 0.760215] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.899775] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.902890] ata1.00: ATAPI: ASUS DRW-24B1ST c, 1.05, max UDMA/100
[ 0.908892] ata1.00: configured for UDMA/100
[ 1.401395] tsc: Refined TSC clocksource calibration: 2210.050 MHz
[ 1.401540] Switching to clocksource tsc
[ 3.447995] floppy0: no floppy controllers found
[ 3.451548] scsi 0:0:0:0: CD-ROM ASUS DRW-24B1ST c 1.05 PQ: 0 ANSI: 5
[ 3.455435] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.455677] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.455964] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 3.909577] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.913631] ata2.00: ATA-8: WDC WD5000AAKX-00ERMA0, 15.01H15, max UDMA/133
[ 3.913770] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.916829] ata2.00: configured for UDMA/133
[ 3.917137] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 15.0 PQ: 0 ANSI: 5
[ 3.917535] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.917881] sd 1:0:0:0: [sda] Write Protect is off
[ 3.918019] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.918053] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.923364] sda: sda1 sda2 sda3 sda4
[ 3.923964] sd 1:0:0:0: [sda] Attached SCSI disk
[ 4.230666] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.231002] scsi 4:0:0:0: Direct-Access ATA WDC WD800JB-00JJ 05.0 PQ: 0 ANSI: 5
[ 4.231488] sd 4:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 4.231534] scsi 4:0:1:0: Direct-Access ATA MAXTOR 6L060L3 A93. PQ: 0 ANSI: 5
[ 4.231648] sd 4:0:1:0: [sdc] 117266688 512-byte logical blocks: (60.0 GB/55.9 GiB)
[ 4.231687] ata6: port disabled--ignoring
[ 4.231706] sd 4:0:1:0: [sdc] Write Protect is off
[ 4.231707] sd 4:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 4.231719] sd 4:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.240803] sdc:
[ 4.240967] sd 4:0:0:0: [sdb] Write Protect is off
[ 4.241093] sd 4:0:1:0: [sdc] Attached SCSI disk
[ 4.241236] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.241267] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.249913] sdb: sdb1
[ 4.250457] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 4.250610] registered taskstats version 1
[ 4.251181] md: Waiting for all devices to be available before autodetect
[ 4.251324] md: If you don't use raid, use raid=noautodetect
[ 4.251615] md: Autodetecting RAID arrays.
[ 4.251745] md: Scanned 0 and added 0 devices.
[ 4.251875] md: autorun ...
[ 4.252002] md: ... autorun DONE.
[ 4.270242] EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
[ 4.270712] EXT2-fs (sda2): error: couldn't mount because of unsupported optional features (240)
[ 4.293317] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.293571] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 4.316536] devtmpfs: mounted
[ 4.318167] Freeing unused kernel memory: 1272k freed
[ 4.318637] Write protecting the kernel read-only data: 16384k
[ 4.320333] Freeing unused kernel memory: 552k freed
[ 4.322594] Freeing unused kernel memory: 792k freed
[ 4.889448] loop: module loaded
[ 5.059825] udevd[178]: starting version 182
[ 5.667286] microcode: CPU0: patch_level=0x010000c6
[ 5.667719] parport_pc 00:03: reported by Plug and Play ACPI
[ 5.667904] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 5.701778] microcode: CPU0: new patch_level=0x010000db
[ 5.701932] microcode: CPU1: patch_level=0x010000c6
[ 5.702074] microcode: CPU1: new patch_level=0x010000db
[ 5.702223] microcode: CPU2: patch_level=0x010000c6
[ 5.702367] microcode: CPU2: new patch_level=0x010000db
[ 5.702504] microcode: CPU3: patch_level=0x010000c6
[ 5.702643] microcode: CPU3: new patch_level=0x010000db
[ 5.702838] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 5.783940] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 5.784195] ACPI: Power Button [PWRB]
[ 5.784370] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.784607] ACPI: Power Button [PWRF]
[ 5.796277] kvm: Nested Virtualization enabled
[ 5.796416] kvm: Nested Paging enabled
[ 5.817545] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.834381] i2c i2c-0: nForce2 SMBus adapter at 0x600
[ 5.834776] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.834934] ehci-pci: EHCI PCI platform driver
[ 5.835597] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 5.835755] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
[ 5.835882] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 5.835945] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.835947] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.835948] usb usb1: Product: xHCI Host Controller
[ 5.835949] usb usb1: Manufacturer: Linux 3.10.17 xhci_hcd
[ 5.835950] usb usb1: SerialNumber: 0000:04:00.0
[ 5.836052] xHCI xhci_add_endpoint called for root hub
[ 5.836053] xHCI xhci_check_bandwidth called for root hub
[ 5.836077] hub 1-0:1.0: USB hub found
[ 5.836085] hub 1-0:1.0: 4 ports detected
[ 5.836185] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 5.836261] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2
[ 5.836291] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 5.836292] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.836293] usb usb2: Product: xHCI Host Controller
[ 5.836294] usb usb2: Manufacturer: Linux 3.10.17 xhci_hcd
[ 5.836295] usb usb2: SerialNumber: 0000:04:00.0
[ 5.836372] xHCI xhci_add_endpoint called for root hub
[ 5.836372] xHCI xhci_check_bandwidth called for root hub
[ 5.836392] hub 2-0:1.0: USB hub found
[ 5.836399] hub 2-0:1.0: 4 ports detected
[ 5.840050] ACPI Warning: 0x0000000000000700-0x000000000000073f SystemIO conflicts with Region \_SB_.PCI0.SM00 1 (20130328/utaddress-251)
[ 5.840344] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.840747] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 5.840753] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 5.840971] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 5.841255] ohci_hcd 0000:00:02.0: irq 23, io mem 0xefeff000
[ 5.857262] ppdev: user-space parallel port driver
[ 5.879595] i2c /dev entries driver
[ 5.894145] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.894286] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.894537] usb usb3: Product: OHCI Host Controller
[ 5.894674] usb usb3: Manufacturer: Linux 3.10.17 ohci_hcd
[ 5.894806] usb usb3: SerialNumber: 0000:00:02.0
[ 5.895082] hub 3-0:1.0: USB hub found
[ 5.895109] Linux agpgart interface v0.103
[ 5.895350] hub 3-0:1.0: 10 ports detected
[ 5.895738] ehci-pci 0000:00:02.1: setting latency timer to 64
[ 5.895930] ehci-pci 0000:00:02.1: EHCI Host Controller
[ 5.896143] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 4
[ 5.896398] ehci-pci 0000:00:02.1: debug port 1
[ 5.896554] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[ 5.896576] ehci-pci 0000:00:02.1: irq 22, io mem 0xefefec00
[ 5.902127] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 5.902294] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.902429] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.902678] usb usb4: Product: EHCI Host Controller
[ 5.902810] usb usb4: Manufacturer: Linux 3.10.17 ehci_hcd
[ 5.902945] usb usb4: SerialNumber: 0000:00:02.1
[ 5.903228] hub 4-0:1.0: USB hub found
[ 5.903369] hub 4-0:1.0: 10 ports detected
[ 5.905129] [drm] Initialized drm 1.1.0 20060810
[ 5.906662] acpi-cpufreq: overriding BIOS provided _PSD data
[ 5.952148] hub 3-0:1.0: USB hub found
[ 5.952287] hub 3-0:1.0: 10 ports detected
[ 5.998463] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 5.998602] hda_intel: Disabling MSI
[ 5.998757] snd_hda_intel 0000:00:05.0: setting latency timer to 64
[ 6.187935] usb 1-4: new high-speed USB device number 2 using xhci_hcd
[ 6.189346] wmi: Mapper loaded
[ 6.201423] usb 1-4: New USB device found, idVendor=04e8, idProduct=328b
[ 6.201566] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.201700] usb 1-4: Product: ML-1630 Series
[ 6.201830] usb 1-4: Manufacturer: Samsung Electronics Co., Ltd.
[ 6.201966] usb 1-4: SerialNumber: 4561BFFS904549E.
[ 6.202204] usb 1-4: ep 0x1 - rounding interval to 8 microframes, ep desc says 10 microframes
[ 6.202449] usb 1-4: ep 0x82 - rounding interval to 8 microframes, ep desc says 10 microframes
[ 6.979411] input: HDA NVidia Front Headphone as /devices/pci0000:00/0000:00:05.0/sound/card0/input4
[ 6.979754] input: HDA NVidia Line Out as /devices/pci0000:00/0000:00:05.0/sound/card0/input5
[ 6.980045] input: HDA NVidia Line as /devices/pci0000:00/0000:00:05.0/sound/card0/input6
[ 6.980337] input: HDA NVidia Rear Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input7
[ 6.980622] input: HDA NVidia Front Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input8
[ 6.981049] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 6.981561] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
[ 6.981702] forcedeth 0000:00:07.0: setting latency timer to 64
[ 7.047024] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input9
[ 7.503736] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr d0:50:99:5e:86:14
[ 7.503995] forcedeth 0000:00:07.0: highdma pwrctl mgmt gbit lnktim msi desc-v3
[ 7.504283] nouveau 0000:00:0d.0: setting latency timer to 64
[ 7.504530] ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 21
[ 7.504892] nouveau [ DEVICE][0000:00:0d.0] BOOT0 : 0x04c000a2
[ 7.505037] nouveau [ DEVICE][0000:00:0d.0] Chipset: C61 (NV4C)
[ 7.505169] nouveau [ DEVICE][0000:00:0d.0] Family : NV40
[ 7.506084] nouveau [ VBIOS][0000:00:0d.0] checking PRAMIN for image...
[ 7.543180] nouveau [ VBIOS][0000:00:0d.0] ... appears to be valid
[ 7.543312] nouveau [ VBIOS][0000:00:0d.0] using image from PRAMIN
[ 7.543624] nouveau [ VBIOS][0000:00:0d.0] BIT signature found
[ 7.543757] nouveau [ VBIOS][0000:00:0d.0] version 05.61.32.28.01
[ 7.544141] nouveau [ PFB][0000:00:0d.0] RAM type: unknown
[ 7.544290] nouveau [ PFB][0000:00:0d.0] RAM size: 256 MiB
[ 7.544440] nouveau [ PFB][0000:00:0d.0] ZCOMP: 0 tags
[ 7.570253] nouveau [ PTHERM][0000:00:0d.0] FAN control: none / external
[ 7.570411] nouveau [ PTHERM][0000:00:0d.0] fan management: disabled
[ 7.570562] nouveau [ PTHERM][0000:00:0d.0] internal sensor: no
[ 7.590790] [TTM] Zone kernel: Available graphics memory: 1889844 kiB
[ 7.590943] [TTM] Initializing pool allocator
[ 7.591093] [TTM] Initializing DMA pool allocator
[ 7.591617] nouveau [ DRM] VRAM: 253 MiB
[ 7.591771] nouveau [ DRM] GART: 512 MiB
[ 7.591933] nouveau [ DRM] TMDS table version 1.1
[ 7.592082] nouveau [ DRM] DCB version 3.0
[ 7.592231] nouveau [ DRM] DCB outp 00: 01000310 00000023
[ 7.592381] nouveau [ DRM] DCB outp 01: 00110204 942b0003
[ 7.592530] nouveau [ DRM] DCB conn 00: 0000
[ 7.592700] nouveau [ DRM] DCB conn 01: 1131
[ 7.592871] nouveau [ DRM] DCB conn 02: 0110
[ 7.593040] nouveau [ DRM] DCB conn 03: 0111
[ 7.593209] nouveau [ DRM] DCB conn 04: 0113
[ 7.593488] nouveau [ DRM] Saving VGA fonts
[ 7.629906] nouveau W[ DRM] DCB type 4 not known
[ 7.630056] nouveau W[ DRM] Unknown-1 has no encoders, removing
[ 7.631236] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.631386] [drm] No driver support for vblank timestamp query.
[ 7.632245] nouveau [ DRM] 1 available performance level(s)
[ 7.632396] nouveau [ DRM] 0: core 425MHz shader 425MHz fanspeed 100%
[ 7.632546] nouveau [ DRM] c:
[ 7.633928] nouveau [ DRM] MM: using M2MF for buffer copies
[ 7.682807] nouveau [ DRM] allocated 1360x768 fb: 0x9000, bo ffff88012a2df400
[ 7.683210] fbcon: nouveaufb (fb0) is primary device
[ 7.748757] Console: switching to colour frame buffer device 170x48
[ 7.750381] nouveau 0000:00:0d.0: fb0: nouveaufb frame buffer device
[ 7.750391] nouveau 0000:00:0d.0: registered panic notifier
[ 7.750403] [drm] Initialized nouveau 1.1.1 20120801 for 0000:00:0d.0 on minor 0
[ 7.804861] i2c i2c-3: sendbytes: NAK bailout.
[ 8.082747] Adding 7815584k swap on /dev/sda1. Priority:-1 extents:1 across:7815584k
[ 8.153312] fuse init (API version 7.22)
[ 8.819085] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 9.182900] lp0: using parport0 (interrupt-driven).
[ 9.182917] lp0: console ready
[ 12.593227] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 12.649521] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 12.656390] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.005768] forcedeth 0000:00:07.0: irq 44 for MSI/MSI-X
[ 15.005796] forcedeth 0000:00:07.0 eth0: MSI enabled
[ 22.794820] NET: Registered protocol family 10
[ 71.050798] nouveau E[ PBUS][0000:00:0d.0] MMIO write of 0x00460001 FAULT at 0x00b000
[ 96.879515] nouveau E[ PBUS][0000:00:0d.0] MMIO write of 0x00c20001 FAULT at 0x00b010
[ 98.176112] nouveau E[ PBUS][0000:00:0d.0] MMIO write of 0x00000000 FAULT at 0x00b010

Emerson 06-02-2016 09:39 AM
A quick google revealed nouveau.config=NvMSI=0 is worth a try.

skippy1729 06-02-2016 09:43 AM
Quote:
Originally Posted by Emerson (Post 5554583)
A quick google revealed nouveau.config=NvMSI=0 is worth a try.
Thanks but I have no idea what this means or what I should try.

Emerson 06-02-2016 09:55 AM
It is kernel command line parameter.


All times are GMT -5. The time now is 01:42 AM.
Page 1 of 3 1 23
Show 50 post(s) from this thread on one page