LinuxQuestions.org
Register a domain and help support LQ
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie
User Name
Password
Linux - Newbie This Linux forum is for members that are new to Linux.
Just starting out and have a question? If it is not in the man pages or the how-to's this is the place!

Notices

Reply
 
Search this Thread
Old 11-21-2007, 05:08 AM   #1
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Rep: Reputation: 0
ethernet card is not detecting


hi
i am new to linux,my system ethernet card in linux is not detect but it show in window xp sp2,in xp it show like network adapter broadcom netlink(tm)gigabit ethernet. what is the problem ,how i detect my ethernet card.in linux if we type command ifconfig it output is
ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1547 errors:0 dropped:0 overruns:0 frame:0
TX packets:1547 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1345578 (1.2 MiB) TX bytes:1345578 (1.2 MiB)
i want to start my internet. what i do .plz help me
 
Old 11-21-2007, 05:34 AM   #2
Fantasio
Member
 
Registered: Nov 2007
Location: Vinsobres - Drome - France
Distribution: SuSE Linux 11.3
Posts: 148

Rep: Reputation: 18
What's your distro ?
 
Old 11-21-2007, 06:24 AM   #3
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Original Poster
Rep: Reputation: 0
ethernet card is not detecting in linux but detecting in xp

hi
i am using dual operating system on my pc .one is redhat enterprice linux ES version 4 and other is window XP SP2.we have 5 partion 1st one is primary in which XP install(c drive),partion 2nd,3rd,4th is used by window,in last partion i install linux.but problem is that network card is not detecting in linux while detecting in window xp.in window xp it show like broadcom netlink(tm)gigabit.some one suggest command ifconfig for detail it output is

ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1547 errors:0 dropped:0 overruns:0 frame:0
TX packets:1547 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1345578 (1.2 MiB) TX bytes:1345578 (1.2 MiB)

some one suggested lspci -v its output is
[root@localhost ~]# lspci -v
00:00.0 Host bridge: Intel Corporation Memory Controller Hub (rev 02)
Subsystem: Lenovo: Unknown device 1015
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information

00:01.0 PCI bridge: Intel Corporation PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Flags: fast devsel
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 0000000000000000-0000000000000000
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 3
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)

00:02.0 VGA compatible controller: Intel Corporation Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Lenovo: Unknown device 1015
Flags: bus master, fast devsel, latency 0, IRQ 169
Memory at d0000000 (32-bit, non-prefetchable) [size=1M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
I/O ports at 18c0 [size=8]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Capabilities: [d0] Power Management version 2

00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: Lenovo: Unknown device 1015
Flags: bus master, fast devsel, latency 0, IRQ 177
Memory at d0200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
how i detect ethernet card in linux
 
Old 11-21-2007, 06:46 AM   #4
KrahnacK
Member
 
Registered: Nov 2007
Location: /dev/volcano
Posts: 70

Rep: Reputation: 15
to know exactly what your network card is, you type "lspci" in a terminal.

there are several types of gigabit ethernet cards made by broadcom, but from what i know, they're all supported in linux
 
Old 11-21-2007, 07:09 AM   #5
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Original Poster
Rep: Reputation: 0
when using lspci output is

04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5786 Gigabit Ethernet PCI Express (rev 02)
Subsystem: Lenovo: Unknown device 1015
Flags: bus master, fast devsel, latency 0, IRQ 185
Memory at d0100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Capabilities: [50] Vital Product Data
Capabilities: [58] Vendor Specific Information
Capabilities: [e8] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Capabilities: [d0] Express Endpoint IRQ 0
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number 46-77-e6-fe-ff-58-15-00
Capabilities: [16c] Power Budgeting
 
Old 11-21-2007, 07:12 AM   #6
jaseka
LQ Newbie
 
Registered: Oct 2007
Posts: 15

Rep: Reputation: 0
First confirm, the driver for your NIC loaded ?

for example

The driver for RealTek NIC is e100

by using "lsmod" command
you can check whether your NIC detected by using "dmesg"


If the driver not loaded, it can be loaded from first Linux installation CD.
 
Old 11-21-2007, 07:19 AM   #7
jaseka
LQ Newbie
 
Registered: Oct 2007
Posts: 15

Rep: Reputation: 0
Load relevant NIC driver then only Linux can detect NIC
 
Old 11-21-2007, 11:45 AM   #8
Tinkster
Moderator
 
Registered: Apr 2002
Location: in a fallen world
Distribution: slackware by choice, others too :} ... android.
Posts: 22,986
Blog Entries: 11

Rep: Reputation: 880Reputation: 880Reputation: 880Reputation: 880Reputation: 880Reputation: 880Reputation: 880
I merged your two threads on the same topic; in the future
please stick to the rules, and don't double post.
 
Old 11-21-2007, 12:20 PM   #9
KrahnacK
Member
 
Registered: Nov 2007
Location: /dev/volcano
Posts: 70

Rep: Reputation: 15
sorry for being late again...didn't see your second post

the kernel module you look for is tg3, according to :

http://www.broadcom.com/support/ethe...ic/netlink.php

so you may want to do a
Code:
modprobe tg3
and see if the module is loaded with
Code:
lsmod | grep tg3
and see what happenned with dmesg if the above command doesn't display anything
 
Old 11-21-2007, 11:47 PM   #10
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Original Poster
Rep: Reputation: 0
output to your suggestion

[root@localhost ~]# modprobe tg3
[root@localhost ~]# lsmod |grep tg3
tg3 106821 0

when i used dmesg output is

[root@localhost ~]# dmesg
Linux version 2.6.9-42.EL (bhcompile@hs20-bc1-1.build.redhat.com) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-2)) #1 Wed Jul 12 23:16:43 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004f680000 (usable)
BIOS-e820: 000000004f680000 - 000000004f690000 (ACPI data)
BIOS-e820: 000000004f690000 - 000000004f700000 (ACPI NVS)
BIOS-e820: 000000004f700000 - 0000000050000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
374MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7190
Using x86 segment limits to approximate NX protection
zapping low mappings.
On node 0 totalpages: 325248
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 95872 pages, LIFO batch:16
DMI present.
ACPI: RSDP (v000 LENOVO ) @ 0x000f6fe0
ACPI: RSDT (v001 LENOVO TC-2O 0x00000040 LTP 0x00000000) @ 0x4f6887b9
ACPI: FADT (v001 LENOVO TC-2O 0x00000040 PTL 0x00000003) @ 0x4f68fe8e
ACPI: TCPA (v002 LENOVO THI2OCEN 0x00000040 PTL 0x00000001) @ 0x4f68ff02
ACPI: MCFG (v001 PTLTD M2OG 0x00000040 LTP 0x00000000) @ 0x4f68ff34
ACPI: MADT (v001 PTLTD A2OC 0x00000040 LTP 0x00000000) @ 0x4f68ff70ACPI: BOOT (v001 PTLTD $SB2OBL$ 0x00000040 LTP 0x00000001) @ 0x4f68ffd8
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050228) @ 0x4f6887f5
ACPI: DSDT (v001 INTEL BR_2OTER 0x00000040 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:6 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:6 APIC version 20
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Enabling APIC mode: Flat. Using 0 I/O APICs
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ11 used by override.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 60000000 (gap: 50000000:aec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c03ff000 soft=c03fe000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2993.692 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1284920k/1300992k available (2150k kernel code, 15088k reserved, 712k data, 164k init, 383488k highmem)
Calibrating delay using timer specific routine.. 5989.79 BogoMIPS (lpj=2994896)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring handled by SMI
CPU: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 492k freed
NET: Registered protocol family 16
PCI: BIOS BUG #81[00000296] found
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 11 14 15) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *10 11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 185
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1195728043.813:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8301CD821788A86B
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: HL-DT-ST RW/DVD GCC-H20N, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Using cfq io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 48X DVD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Generic Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 131072 (order: 9, 3670016 bytes)
TCP: Hash tables configured (established 262144 bind 131072)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
EXP1 EXP2 PCIB KBC0 COMA AC97 PWRB USB1 USB2 USB3 USB4 EUSB
Freeing unused kernel memory: 164k freed
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 201
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18B0 irq 14
ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4123 85:7469 86:bf41 87:4123 88:207f
ata1: dev 0 ATA-7, max UDMA/133, 312581808 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
Vendor: ATA Model: WDC WD1600AAJS-0 Rev: 05.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 4 roles, 355 types, 26 bools
security: 55 classes, 22582 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda8, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
inserting floppy driver for 2.6.9-42.EL
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hw_random hardware driver 1.0.0 loaded
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 193, pci mem f88ec000
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 193, io base 00001800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 201, io base 00001820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 209, io base 00001840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.3: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 169, io base 00001860
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 3-1: new low speed USB device using address 2
input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.1-1
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0383d60(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
mtrr: no more MTRRs available
mtrr: no more MTRRs available
ACPI: Power Button (FF) [PWRF]
EXT3 FS on sda8, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
cdrom: open failed.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev sda5, type vfat), uses genfs_contexts
SELinux: initialized (dev sda6, type vfat), uses genfs_contexts
SELinux: initialized (dev sda7, type vfat), uses genfs_contexts
Adding 1020088k swap on /dev/sda9. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: No new microdata for cpu 0
IA-32 Microcode Update Driver v1.14 unregistered
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 356 bytes per conntrack
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
mtrr: no more MTRRs available
mtrr: no more MTRRs available

what to do next my proble is not solved
 
Old 11-22-2007, 06:49 AM   #11
KrahnacK
Member
 
Registered: Nov 2007
Location: /dev/volcano
Posts: 70

Rep: Reputation: 15
what if you try
Code:
ifconfig sit0 up
does that print a "no such interface" or not ?
 
Old 11-28-2007, 04:15 AM   #12
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Original Poster
Rep: Reputation: 0
proble not solved

hi
my problem not solved yet ,plz help me
 
Old 12-13-2007, 05:11 AM   #13
mrahultiwari
LQ Newbie
 
Registered: Nov 2007
Posts: 9

Original Poster
Rep: Reputation: 0
hi
my problem not solved yet ,plz help me
 
Old 12-13-2007, 11:01 AM   #14
KrahnacK
Member
 
Registered: Nov 2007
Location: /dev/volcano
Posts: 70

Rep: Reputation: 15
so i'll repeat my question : what happens if you type
Code:
ifconfig sit0 up
it could be because your network interface isn't named eth0 (which is standard name), but sit0
if it says something like "no such interface", then i can't really help you out...since the driver (tg3 here) should provide you with a network interface other than lo, may be trying another one that could match your card would help?

if it doesn't complain about a missing interface, then you have it : just pick up a tutorial (on your distro's site would be best) on how to setup networking and replace every eth0 with sit0 and you're done.

good luck
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem detecting the ethernet interface indu.a Linux - Kernel 6 11-22-2006 01:08 PM
debian not detecting wireless ethernet card macmanus_bros Linux - Hardware 2 06-27-2005 09:51 PM
Auto-detecting ethernet? ub3rj3phf Red Hat 1 11-03-2004 02:10 AM
Ethernet card on laptop: I installed my D-Link ethernet card into Redhat 9, not detec brighamr Linux - Hardware 0 05-18-2004 12:33 AM
Problems with detecting ethernet card brokenflea *BSD 2 03-06-2004 02:05 AM


All times are GMT -5. The time now is 11:54 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration