LinuxQuestions.org
Visit the LQ Articles and Editorials section
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking
User Name
Password
Linux - Networking This forum is for any issue related to networks or networking.
Routing, network cards, OSI, etc. Anything is fair game.

Notices

Reply
 
Search this Thread
Old 11-24-2006, 06:19 PM   #1
nixau2
LQ Newbie
 
Registered: Nov 2006
Posts: 2

Rep: Reputation: 0
Problem with network on slack 11 and intel card


Hi all. I have some problem with network card on my slackware 11. First of all i have slack 10 and realtek network card. The internet works well, but when i install on new disk (scsi Samsung 9,1 GB and Adaptec card) slackware 10.2 i have some problem with network.

The problem is that from time to time my server is not response - he is going "sleep" (any kind of services like ssh, ftp, www, mail don't response from internet but on local works well). When i send a ping it's returning "Request timed out", but when send couple of packet to my server (some times is just 8 packet and another time i must ping it about 2-3 minutes) server is respond and work.

There isn't any informations in system logs about not working network card. So i upgrade slackware from version 10.2 to 11 because i think that's a problem with old driver version (or sbme mistake in packet). But the problem isn't resolve.

#dmsg
Code:
eepro100.c:v1.09j-t 9/29/99 Donald Becker 
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
PCI: Found IRQ 12 for device 00:0a.0
eth0: OEM i82557/i82558 10/100 Ethernet, IRQ 12.
  Board assembly 736294-006, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
PCI: Found IRQ 5 for device 00:0b.0
eth1: PCI device 8086:1229, IRQ 5.
  Board assembly 751767-004, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
    Secondary interface chip i82555.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x3258698e)
#mii-tool
Code:
eth0: negotiated 100baseTx-FD flow-control, link ok
eth1: negotiated 100baseTx-FD flow-control, link ok
#eth-tool eth0
Code:
Settings for eth0:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Current message level: 0x000020c1 (8385)
        Link detected: yes
#eth-tool eth1
Code:
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Current message level: 0x000020c1 (8385)
        Link detected: yes
#lspci -vvv
Code:
00:0a.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08)
        Subsystem: IBM 10/100 EtherJet Adapter with Alert on LAN
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 12
        Region 0: Memory at eb522000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at e800 [size=64]
        Region 2: Memory at eb400000 (32-bit, non-prefetchable) [size=1M]
        Expansion ROM at e9000000 [disabled] [size=1M]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:0b.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0c)
        Subsystem: Intel Corporation EtherExpress PRO/100 S Desktop Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at eb520000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at ec00 [size=64]
        Region 2: Memory at eb500000 (32-bit, non-prefetchable) [size=128K]
        Expansion ROM at ea000000 [disabled] [size=64K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

I don't known where is problem so anyone can help me?

ps. sorry for my english
 
Old 11-26-2006, 06:45 AM   #2
allend
Senior Member
 
Registered: Oct 2003
Location: Melbourne
Distribution: Slackware-current
Posts: 3,433

Rep: Reputation: 849Reputation: 849Reputation: 849Reputation: 849Reputation: 849Reputation: 849Reputation: 849
Sounds like a power management setting. Check your BIOS settings.
 
Old 11-27-2006, 05:57 PM   #3
nixau2
LQ Newbie
 
Registered: Nov 2006
Posts: 2

Original Poster
Rep: Reputation: 0
Quote:
Originally Posted by allend
Sounds like a power management setting. Check your BIOS settings.
APM is turned off in BIOS, because mainboard is too old and realy i don't need this. Previouse version of slackware (i mean 10.0) works well without problems. Two days ago i'm upgrades all packages to current version and problem is still not resolve.

Maybe there is a some tools to testing network card - anyone known any of this kind tools?
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Can't install Intel(R) Pro/100 VE Network Card hombero Linux - Hardware 1 09-20-2006 06:01 PM
Intel Pro network card problems on FC3 saniok Linux - Hardware 2 04-14-2005 02:30 PM
Starting Intel Net Card In Slack 9.1 On Desktop sxa Slackware 3 02-22-2004 01:50 PM
Intel network card not dectected, how to fix? warsawcrew Linux - Hardware 5 01-22-2004 01:11 PM
Can't network pcmcia card with Intel eepro100 ethernet card. RKris Linux - Networking 1 06-18-2002 12:43 PM


All times are GMT -5. The time now is 11:34 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration