LinuxQuestions.org
Help answer threads with 0 replies.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking
User Name
Password
Linux - Networking This forum is for any issue related to networks or networking.
Routing, network cards, OSI, etc. Anything is fair game.

Notices


Reply
  Search this Thread
Old 02-10-2003, 09:51 AM   #1
kram-haren
LQ Newbie
 
Registered: Feb 2003
Posts: 1

Rep: Reputation: 0
pppd problems


Hi,
I'm getting frustrated with my pppd problems. I call my organisation using pppd v2.4.1 (support for MS-CHAP and MS cbcp). I get the connection, and ifconfig reports ppp0. But I can't even ping the remote ip address shown by ifconfig for ppp0.
When I try 'ping -s 1000 remote-ip-address' - I see the Tx field of ifconfig rapidly increase, but the Rx changes by 2/3 bytes only. Any ideas?
I've attached the pppd log files, and ifconfig and route -n outputs below. Thanks in advance for your responses.

-Ramesh

ppp0 Link encap:Point-to-Point Protocol
inet addr:192.168.1.1 P-t-P:10.87.3.121 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:1637 errors:0 dropped:0 overruns:0 frame:0
TX packets:1893 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:11277 (11.0 Kb) TX bytes:48109 (46.9 Kb)

eth0 Link encap:Ethernet HWaddr 00:10C:77:9F:56
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::210:dcff:fe77:9f56/10 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:436 (436.0 b)
Interrupt:5 Base address:0xec00

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:645 errors:0 dropped:0 overruns:0 frame:0
TX packets:645 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:52281 (51.0 Kb) TX bytes:52281 (51.0 Kb)


linux:/etc/ppp # route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.87.3.121 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 10.87.3.121 0.0.0.0 UG 0 0 0 ppp0

Feb 8 18:38:55 linux pppd[1636]: pppd 2.4.1 started by kram, uid 0
Feb 8 18:38:55 linux pppd[1636]: Perms of /dev/modem are ok, no 'mesg n' neccesary.
Feb 8 18:38:56 linux chat[1637]: timeout set to 60 seconds
Feb 8 18:38:56 linux chat[1637]: abort on (BUSY)
Feb 8 18:38:56 linux chat[1637]: abort on (NO DIALTONE)
Feb 8 18:38:56 linux chat[1637]: abort on (ERROR)
Feb 8 18:38:56 linux chat[1637]: abort on (NO CARRIER)
Feb 8 18:38:56 linux chat[1637]: send (+++ATZ^M)
Feb 8 18:38:57 linux chat[1637]: expect (OK)
Feb 8 18:38:57 linux chat[1637]: +++ATZ^M^M
Feb 8 18:38:57 linux chat[1637]: OK
Feb 8 18:38:57 linux chat[1637]: -- got it
Feb 8 18:38:57 linux chat[1637]: send (ATE1Q0&C1&S0DT0521597010^M)
Feb 8 18:38:58 linux chat[1637]: expect (CONNECT)
Feb 8 18:38:58 linux chat[1637]: ^M
Feb 8 18:39:28 linux chat[1637]: ATE1Q0&C1&S0DT0521597010^M^M
Feb 8 18:39:28 linux chat[1637]: CONNECT
Feb 8 18:39:28 linux chat[1637]: -- got it
Feb 8 18:39:28 linux chat[1637]: send (^M)
Feb 8 18:39:28 linux pppd[1636]: Serial connection established.
Feb 8 18:39:28 linux pppd[1636]: using channel 7
Feb 8 18:39:28 linux pppd[1636]: Using interface ppp0
Feb 8 18:39:28 linux pppd[1636]: Connect: ppp0 <--> /dev/modem
Feb 8 18:39:29 linux pppd[1636]: sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x7441df3a> <pcomp> <accomp>]
Feb 8 18:39:29 linux pppd[1636]: rcvd [LCP ConfReq id=0x0 <asyncmap 0x0> <auth chap 81> <magic 0x8d35fb0> <pcomp> <accomp> <callback CBCP> <mrru 1614> <endpoint [local:ec.76.c9.b8.b3.ef.4f.ef.a5.94.ea.82.88.e2.a8.1c.00.00.00.00]> < 17 04 00 37>]
Feb 8 18:39:29 linux pppd[1636]: sent [LCP ConfRej id=0x0 <mrru 1614> < 17 04 00 37>]
Feb 8 18:39:29 linux pppd[1636]: rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x7441df3a> <pcomp> <accomp>]
Feb 8 18:39:30 linux pppd[1636]: rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap 81> <magic 0x8d35fb0> <pcomp> <accomp> <callback CBCP> <endpoint [local:ec.76.c9.b8.b3.ef.4f.ef.a5.94.ea.82.88.e2.a8.1c.00.00.00.00]>]
Feb 8 18:39:30 linux pppd[1636]: sent [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap 81> <magic 0x8d35fb0> <pcomp> <accomp> <callback CBCP> <endpoint [local:ec.76.c9.b8.b3.ef.4f.ef.a5.94.ea.82.88.e2.a8.1c.00.00.00.00]>]
Feb 8 18:39:30 linux pppd[1636]: sent [LCP EchoReq id=0x0 magic=0x7441df3a]
Feb 8 18:39:30 linux pppd[1636]: cbcp_lowerup
Feb 8 18:39:30 linux pppd[1636]: want: 12
Feb 8 18:39:30 linux pppd[1636]: phone no: 5343985
Feb 8 18:39:30 linux pppd[1636]: rcvd [CHAP Challenge id=0x0 <7ea35618acaa2f5cca6008291977c706>, name = "NTSERVER3"]
Feb 8 18:39:30 linux pppd[1636]: sent [CHAP Response id=0x0 <d35e5e6d9f101b4faaa8a627498ae90e0000000000000000e3fb2e27c5e80de174d6df69ebafbcbfcb2b2cb95937c8be00> , name = "ramesh"]
Feb 8 18:39:30 linux pppd[1636]: rcvd [LCP EchoRep id=0x0 magic=0x8d35fb0]
Feb 8 18:39:30 linux pppd[1636]: rcvd [CHAP Success id=0x0 "S=19643F04264CF7C3EA8BF3C2AF7C97BB5F5796E2"]
Feb 8 18:39:30 linux pppd[1636]: Remote message: S=19643F04264CF7C3EA8BF3C2AF7C97BB5F5796E2
Feb 8 18:39:30 linux pppd[1636]: cbcp_open
Feb 8 18:39:30 linux pppd[1636]: cbcp_req CONF_USER
Feb 8 18:39:30 linux pppd[1636]: sent [CBCP Request id=0x1 < UserDefined delay = 5 number = 534398>] 35 33 34 33 39 38
Feb 8 18:39:30 linux pppd[1636]: rcvd [CBCP Request id=0x1 < AdminDefined delay = 0>]
Feb 8 18:39:30 linux pppd[1636]: length: 3
Feb 8 18:39:30 linux pppd[1636]: Callback: user admin defined
Feb 8 18:39:30 linux pppd[1636]: cbcp_resp cb_type=8
Feb 8 18:39:30 linux pppd[1636]: cbcp_resp CONF_ADMIN
Feb 8 18:39:30 linux pppd[1636]: sent [CBCP Response id=0x1 < AdminDefined delay = 5>]
Feb 8 18:39:30 linux pppd[1636]: rcvd [CBCP Ack id=0x1 < AdminDefined delay = 5>]
Feb 8 18:39:30 linux pppd[1636]: cbcp_lowerdown
Feb 8 18:39:30 linux pppd[1636]: sent [LCP TermReq id=0x2 "Call me back, please"]
Feb 8 18:39:30 linux pppd[1636]: rcvd [LCP TermAck id=0x2 "Call me back, please"]
Feb 8 18:39:30 linux pppd[1636]: Connection terminated.
Feb 8 18:39:31 linux pppd[1636]: Exit.
Feb 8 18:39:31 linux pppd[1666]: pppd 2.4.1 started by kram, uid 0
Feb 8 18:39:32 linux chat[1667]: timeout set to 120 seconds
Feb 8 18:39:32 linux chat[1667]: abort on (NO CARRIER)
Feb 8 18:39:32 linux chat[1667]: abort on (BUSY)
Feb 8 18:39:32 linux chat[1667]: abort on (NO DIALTONE)
Feb 8 18:39:32 linux chat[1667]: abort on (ERROR)
Feb 8 18:39:32 linux chat[1667]: send (+++ATZ^M)
Feb 8 18:39:32 linux chat[1667]: expect (OK)
Feb 8 18:39:33 linux chat[1667]: +++ATZ^M^M
Feb 8 18:39:33 linux chat[1667]: OK
Feb 8 18:39:33 linux chat[1667]: -- got it
Feb 8 18:39:33 linux chat[1667]: send (ATE1Q0&C1&S0^M)
Feb 8 18:39:33 linux chat[1667]: expect (RING)
Feb 8 18:39:33 linux chat[1667]: ^M
Feb 8 18:39:34 linux chat[1667]: ATE1Q0&C1&S0^M^M
Feb 8 18:39:34 linux chat[1667]: OK^M
Feb 8 18:39:38 linux chat[1667]: ^M
Feb 8 18:39:38 linux chat[1667]: RING
Feb 8 18:39:38 linux chat[1667]: -- got it
Feb 8 18:39:38 linux chat[1667]: send (ATA^M)
Feb 8 18:39:38 linux chat[1667]: expect (CONNECT)
Feb 8 18:39:38 linux chat[1667]: ^M
Feb 8 18:40:00 linux chat[1667]: ATA^M^M
Feb 8 18:40:00 linux chat[1667]: CONNECT
Feb 8 18:40:00 linux chat[1667]: -- got it
Feb 8 18:40:00 linux chat[1667]: send (^M)
Feb 8 18:40:00 linux pppd[1666]: Serial connection established.
Feb 8 18:40:00 linux pppd[1666]: Using interface ppp0
Feb 8 18:40:00 linux pppd[1666]: Connect: ppp0 <--> /dev/modem
Feb 8 18:40:01 linux pppd[1666]: Remote message: S=D1560BA4F52F2F79E3D3FB5877F86D163A8241F4
Feb 8 18:40:02 linux pppd[1666]: local IP address 192.168.1.1
Feb 8 18:40:02 linux pppd[1666]: remote IP address 10.87.3.121
Feb 8 18:40:02 linux pppd[1666]: Script /etc/ppp/ip-up finished (pid 1682), status = 0x0

Feb 8 19:27:13 linux pppd[1666]: Script /etc/ppp/ip-down finished (pid 2080), status = 0x0
Feb 8 19:27:13 linux pppd[1666]: Connection terminated.
Feb 8 19:27:13 linux pppd[1666]: Connect time 47.3 minutes.
Feb 8 19:27:13 linux pppd[1666]: Sent 48209 bytes, received 11377 bytes.
Feb 8 19:27:14 linux pppd[1666]: Exit.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
pppd problems fwashington Linux - Hardware 4 08-08-2004 04:50 PM
pppd died: pppd options error (exit code 2 taveirac Linux - Networking 1 02-12-2004 10:17 AM
Problems with pppd doctorv Fedora 7 11-21-2003 01:37 PM
pppd problems carlo Linux - Networking 2 10-18-2002 11:50 AM
pppd died: pppd options error (exit code 2) ianwest Linux - Newbie 2 07-31-2002 08:29 AM

LinuxQuestions.org > Forums > Linux Forums > Linux - Networking

All times are GMT -5. The time now is 12:23 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration