LinuxQuestions.org - Ping on one of ethernet port is not happening

- Linux - Networking (https://www.linuxquestions.org/questions/linux-networking-3/)

- - Ping on one of ethernet port is not happening (https://www.linuxquestions.org/questions/linux-networking-3/ping-on-one-of-ethernet-port-is-not-happening-4175512216/)

Ping on one of ethernet port is not happening

Hi All
I have a board MPC8360 where I want to ping from my board to Desktop . In MPC8360 there are 3 ethernet ports

Code:

~ # ifconfig

eth0      Link encap:Ethernet  HWaddr 00:04:9F:EF:01:00  

          inet addr:192.168.1.100  Bcast:192.168.1.255  Mask:255.255.255.0

          UP BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

          Base address:0x2000 



eth1      Link encap:Ethernet  HWaddr 00:04:9F:EF:01:01  

          inet addr:192.168.2.100  Bcast:192.168.2.255  Mask:255.255.255.0

          UP BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

          Base address:0x3000 



eth2      Link encap:Ethernet  HWaddr 00:04:9F:00:23:25  

          inet addr:10.3.3.203  Bcast:10.3.3.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

          Base address:0x2400 



lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

eth0 and eth1 are able to ping ,but when it comes to eth2 I am not able to ping to Desktop I am gettting error like this

Code:

bytes from 10.3.3.203: Destination Host Unreachable

Vr HL TOS  Len  ID Flg  off TTL Pro  cks      Src      Dst Data

 4  5  c0 0070 1f88  0 0000  40  01 3eaa 10.3.3.203  10.3.3.203 

64 bytes from 10.3.3.203: Destination Host

1. In the above error I see both SRC & Dest IP are same
2. Loopback is happening in eth2 .

Dont know how to forward

Have you checked you have a valid route / gateway / NAT translation to allow your 10.3.3.X subnet to talk to the subnet your desktop is on?

What's the IP/Subnet configuration of your desktop?

continue of thread (Ping on one of ethernet port is not happening)

Hi TenTenths
I am not able to make on reply on this particaular thread (Ping on one of ethernet port is not happening),because of this I am writing reply on this new thread. I am Sorry for this

Its a same desktop which I am successfully pinging on eth0 & eth1 .

Configuration of Desktop is

Code:

ifconfig

eth0      Link encap:Ethernet  HWaddr 10:78:D2:FC:6F:3C  

          inet addr:10.3.3.101  Bcast:10.3.3.255  Mask:255.255.255.0

          inet6 addr: fe80::1278:d2ff:fefc:6f3c/64 Scope:Link

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:56000 errors:0 dropped:0 overruns:0 frame:0

          TX packets:11398 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:5764988 (5.4 MiB)  TX bytes:15596570 (14.8 MiB)

          Interrupt:26 Base address:0x8000 



lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:39 errors:0 dropped:0 overruns:0 frame:0

          TX packets:39 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:3304 (3.2 KiB)  TX bytes:3304 (3.2 KiB)



virbr0    Link encap:Ethernet  HWaddr 6E:2B:2D:FD:2B:82  

          inet addr:192.168.122.1  Bcast:192.168.122.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:56 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:0 (0.0 b)  TX bytes:9225 (9.0 KiB)

I have type some command to check route & gateway list on the board .I hope this may help u ,please let me know if any thing else is needed

netstat -nr

Code:

Kernel IP routing table

Destination    Gateway        Genmask        Flags  MSS Window  irtt Iface

192.168.3.0    0.0.0.0        255.255.255.0  U        0 0          0 eth2

192.168.2.0    0.0.0.0        255.255.255.0  U        0 0          0 eth1

192.168.1.0    0.0.0.0        255.255.255.0  U        0 0          0 eth0

127.0.0.0      0.0.0.0        255.0.0.0      U        0 0          0 lo

0.0.0.0        192.168.3.1    0.0.0.0        UG        0 0          0 eth2

0.0.0.0        192.168.2.1    0.0.0.0        UG        0 0          0 eth1

0.0.0.0        192.168.1.1    0.0.0.0        UG        0 0          0 eth0

ip route show

Code:

192.168.3.0/24 dev eth2  proto kernel  scope link  src 192.168.3.254 

192.168.2.0/24 dev eth1  proto kernel  scope link  src 192.168.2.100 

192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.100

route -n

Code:

Kernel IP routing table

Destination    Gateway        Genmask        Flags Metric Ref    Use Iface

192.168.3.0    0.0.0.0        255.255.255.0  U    0      0        0 eth2

192.168.2.0    0.0.0.0        255.255.255.0  U    0      0        0 eth1

192.168.1.0    0.0.0.0        255.255.255.0  U    0      0        0 eth0

127.0.0.0      0.0.0.0        255.0.0.0      U    0      0        0 lo

0.0.0.0        192.168.3.1    0.0.0.0        UG    0      0        0 eth2

0.0.0.0        192.168.2.1    0.0.0.0        UG    0      0        0 eth1

0.0.0.0        192.168.1.1    0.0.0.0        UG    0      0        0 eth0

At a first look it appears your board has three "default gateways" 192.168.1.1 / 192.168.2.1 / 192.168.3.1

Which of these will route to your 10.3.3.X network?