Seems like a nice forum, first post here
I'm having trouble setting up new Alix (http://www.pcengines.ch/alix6e1.htm
) system with a wireless card. I got the card from an old working Buffalo AirStation router. The card is a WLI-MPCI-G54 and is using Broadcom BCM4306 chip. I've installed Debian on the system.
boat:~# uname -a
Linux boat 2.6.26-2-486 #1 Thu Sep 16 18:43:30 UTC 2010 i586 GNU/Linux
My goal is to make a wireless access point by using hostapd authentication service. I thought it might be a good idea to verify that the wlan-card is working properly first, but it can't seem to detect my local wlan.
iwlist wlan0 scan: wlan0 No scan results
The systems seems to detect the Broadcom chip and uses the b43 driver for it. I've istalled the b43-fwcutter in order to get the firmware
boat:/lib/firmware# ls b43
a0g0bsinitvals4.fw a0g1initvals5.fw lp0bsinitvals13.fw pcm5.fw
a0g0bsinitvals5.fw a0g1initvals9.fw lp0bsinitvals14.fw ucode11.fw
a0g0bsinitvals9.fw b0g0bsinitvals13.fw lp0bsinitvals15.fw ucode13.fw
a0g0initvals4.fw b0g0bsinitvals4.fw lp0initvals13.fw ucode14.fw
a0g0initvals5.fw b0g0bsinitvals5.fw lp0initvals14.fw ucode15.fw
a0g0initvals9.fw b0g0bsinitvals9.fw lp0initvals15.fw ucode4.fw
a0g1bsinitvals13.fw b0g0initvals13.fw n0absinitvals11.fw ucode5.fw
a0g1bsinitvals5.fw b0g0initvals4.fw n0bsinitvals11.fw ucode9.fw
a0g1bsinitvals9.fw b0g0initvals5.fw n0initvals11.fw
a0g1initvals13.fw b0g0initvals9.fw pcm4.fw
I've set the interfaces file to
boat:/etc/network# cat interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
iface lo inet loopback
auto eth0 wlan0
# The primary network interface
iface eth0 inet static
iface wlan0 inet dhcp
I've also installed the wireless-tools package to get the iwconfig and iwlist commands.
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
The last lines outputted by dmesg are
[ 14.710180] b43-phy0: Broadcom 4306 WLAN found
[ 14.758931] input: PC Speaker as /class/input/input0
[ 14.774812] phy0: Selected rate control algorithm 'pid'
[ 14.817042] PCSP: Timer resolution is not sufficient (4000250nS)
[ 14.823082] PCSP: Make sure you have HPET and ACPI enabled.
[ 14.828685] PC-Speaker initialization failed.
[ 14.853216] pcspkr: probe of pcspkr failed with error -5
[ 15.010537] AMD Geode RNG detected
[ 15.131595] Error: Driver 'pcspkr' is already registered, aborting...
[ 16.101869] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 16.602118] Adding 96380k swap on /dev/hda2. Priority:-1 extents:1 across:96380k
[ 17.338626] loop: module loaded
[ 18.428574] eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
[ 18.731268] input: b43-phy0 as /class/input/input1
[ 18.804103] firmware: requesting b43/ucode5.fw
[ 18.872339] firmware: requesting b43/pcm5.fw
[ 18.949062] firmware: requesting b43/b0g0initvals5.fw
[ 19.052153] firmware: requesting b43/b0g0bsinitvals5.fw
[ 19.251803] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 20.601158] Registered led device: b43-phy0::tx
[ 20.605829] Registered led device: b43-phy0::rx
[ 20.610466] Registered led device: b43-phy0::radio
[ 62.077532] NET: Registered protocol family 10
[ 62.086649] lo: Disabled Privacy Extensions
[ 62.098648] ADDRCONF(NETDEV_UP): wlan0: link is not ready
And if i do ifconfig wlan0 down i can se a 0,6W drop in power consumption, so the card seems to be working.
What could the problem be? (ie. i cannot se my wlan network by scanning for it (iwlist wlan0 scan)).