LinuxQuestions.org
Visit the LQ Articles and Editorials section
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking
User Name
Password
Linux - Networking This forum is for any issue related to networks or networking.
Routing, network cards, OSI, etc. Anything is fair game.

Notices

Reply
 
Search this Thread
Old 06-10-2005, 11:51 PM   #1
xgreen
Member
 
Registered: Aug 2003
Distribution: Slackware,Ubuntu
Posts: 389

Rep: Reputation: 30
adsl-setup : what else to configure?


i need to configure adsl on CRUX (newly installed) but always time out. i ran adsl-setup just the same as i ran it on slackware (working fine). is there any configuration/setup that i missed?
 
Old 06-11-2005, 04:47 AM   #2
runlevel0
Member
 
Registered: Mar 2005
Location: Hilversum/Holland
Distribution: Debian GNU/Linux 5.0 (“Lenny”)
Posts: 290

Rep: Reputation: 31
Could you tell what you did?
What does 'time out' mean?

If you are talking about connections timing out check your network settings, you will probably have to change the netmask or the broadcast address.
 
Old 06-13-2005, 09:06 AM   #3
xgreen
Member
 
Registered: Aug 2003
Distribution: Slackware,Ubuntu
Posts: 389

Original Poster
Rep: Reputation: 30
here is my step configuring adsl . those in <xx> are my input

bash-3.00# adsl-setup
>>> Enter your PPPoE user name : <enter myusername>

>>> Enter the Ethernet interface connected to the ADSL modem
(default eth0): <eth0>

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.) <no>

NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no): <no>

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are^M
doing and not modify your DNS setup.
>>> Enter the DNS information here: <server>

>>> Please enter your PPPoE password: <mypassword>
>>> Please re-enter your PPPoE password: <mypassword>

FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
>>> Choose a type of firewall (0-2): 1

my lsmod output

bash-3.00# lsmod
Module Size Used by
ppp_generic 20628 0
slhc 6656 1 ppp_generic


my ifconfig output

bash-3.00# ifconfig
eth0 Link encap:Ethernet HWaddr 00:06:4F:12:1C:16
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:88 errors:0 dropped:0 overruns:0 frame:0
TX packets:88 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6261 (6.1 Kb) TX bytes:8443 (8.2 Kb)
Interrupt:5 Base address:0xc800

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

adsl-start output

bash-3.00# adsl-start
................TIMED OUT




naazmin
 
Old 06-13-2005, 09:12 AM   #4
xgreen
Member
 
Registered: Aug 2003
Distribution: Slackware,Ubuntu
Posts: 389

Original Poster
Rep: Reputation: 30
hmmm... i guess my ppp0 does not exsist in ifconfig output....
 
Old 06-13-2005, 11:01 AM   #5
michaelk
Moderator
 
Registered: Aug 2002
Posts: 11,969

Rep: Reputation: 752Reputation: 752Reputation: 752Reputation: 752Reputation: 752Reputation: 752Reputation: 752
Try this:
ifdown eth0
adsl-start

You can not establish an ADSL connection if eth0 is already configured for an IP.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
adsl-setup or adsl-start not found as user! bnchakraborty Linux - Newbie 2 01-18-2008 10:23 PM
Need some manual to configure adsl little_ball Slackware 1 08-04-2004 08:35 PM
prblms with ADSL setup. no luck after adsl-setup and netconfig Blue_muppet Slackware 2 07-18-2004 01:20 AM
ADSL Routers Setup- Microsom Deskporte router 100 and Planet ADSL modem router mabonline Linux - Hardware 1 02-27-2004 05:36 PM
Configure ADSL Connection mib Linux - Newbie 8 03-13-2003 03:00 PM


All times are GMT -5. The time now is 05:47 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration